English dropdown-ico

Field Controls SK-1 manual

1
2
3
4
5
6
7
8
9
10
11
12

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Field Controls SK-1, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Field Controls SK-1 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Field Controls SK-1. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Field Controls SK-1 should contain:
- informations concerning technical data of Field Controls SK-1
- name of the manufacturer and a year of construction of the Field Controls SK-1 item
- rules of operation, control and maintenance of the Field Controls SK-1 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Field Controls SK-1 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Field Controls SK-1, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Field Controls service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Field Controls SK-1.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Field Controls SK-1 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    STARKAP™ CHIMNEY CAP Model : SK - 1 The MODEL SK Starkap™ is designed for terminating gas vents or metal chimneys for gas or oil heating equipment. English ....... Page 1 Français ..... Page 5 Espanõl ...... Page 8[...]

  • Page 2

    Page 2 INSTALLATION REQUIRE MENTS 1. Install and secure the vertical vent, gas vent or metal chimney according to man ufacturer's instructions or in accordance with NFPA 54 National Fuel Gas code or applicable local codes. The termination of the vertical vent or metal chimney MUST be installed in accordance with the height and roof pitch table[...]

  • Page 3

    Page 3 INSTALLATION 1. Before installation, apply two beads of high temperature sili cone sealant or equivalent around the bottom of the storm collar and 1 inch above the end of the Starkap™ body. (See Figure 2) 2. Insert the Starkap™ into the inside of the vent termination pipe, making sure the Starkap™ is seated against the storm collar. Fa[...]

  • Page 4

    Page 4 SPECIAL VENTING APPL ICATION INSTALLATION SHEET This sheet covers the requirements for installation of the Starkap™ for use with attached buildings designed for the purpose of housing heating equipment outside of the living space of the struct ure. These requirements are based on A.G.A. test reports C - FT - 5 - 90, C - FT - 8 - 90, FT - C[...]

  • Page 5

    Page 5 STARKAP ™ Model : SK - 1 EXIGENCES D’INSTALLA TION 1. Installer et fixer l’évent vertical, l’évent à gaz ou la cheminée en métal conformément aux instructions du fabricant, au code national des gaz combustibles NFPA 54 ou à tout code local applicable. Le bout d’un évent vertical ou d’une cheminée en métal DOIT être ins[...]

  • Page 6

    Page 6 I NSTALLATION 1. Avant l’installation, appliquer deux cordons de scellant de silicone à haute température ou l’équivalent autour de la partie inférieure de la mitre et à 1 po au - dessus de l’extrémité du Starkap™. (Voir Le Schéma 2) 2. Insérer le Starkap™ à l’inté rieur du tuyau de bout d’évent, en s’assurant qu?[...]

  • Page 7

    Page 7 FEUILLE D’INSTALLATI ON POUR ÉVENT SPÉCIA L Cette feuille traite des exigences d’installation du Starkap™ sur des structures contiguës conçu es pour abriter du matériel de chauffage à l’extérieur de l’espace habitable d’une structure. Ces exigences sont basées sur les rapports des tests A.G.A. C - FT - 5 - 90, C - FT - 8 [...]

  • Page 8

    Page 8 StarKap™ M odel : SK - 1 REQUISITOS PARA LA I NSTALACIÓN 1. Instale y asegure el respiradero vertical, el respiradero de gas o la chimenea metálica según las instrucciones del fabricante o confirme al código Nacional sobre Gas Combustible, NFPA 54 o todo código lo cal correspondiente. La terminación del respiradero vertical o de la c[...]

  • Page 9

    Page 9 INSTALACIÓN 1. Antes de la instalación, aplique dos gotas de compuesto sellador de silicona para altas temperaturas o un equivalente alrededor del fondo del collarín y una pulgada encima del extremo del cuerpo del Starkap™. (Ver Figura 2) 2. Introduzca el Starkap™ en el interior del tubo de terminación del respiradero, asegurándose [...]

  • Page 10

    Page 10 HOJA DE INSTALACIÓN PARA LA APLICACIÓN EN SITUACIONES ESPEC IALES DE VENTILACIÓN Esta hoja cubre los requisitos para la instalación del Starkap™ cuando se usa en edificios contiguos diseñados con el fin de alojar equipos de calefacción fuera de la estructura de habitación. Estos requisitos se basan en informes de prueba A.G.A. C - [...]

  • Page 11

    Page 11[...]

  • Page 12

    Page 12 PN 46263300 Rev C 09/00[...]