English dropdown-ico

Craftsman 119.214 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Craftsman 119.214, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Craftsman 119.214 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Craftsman 119.214. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Craftsman 119.214 should contain:
- informations concerning technical data of Craftsman 119.214
- name of the manufacturer and a year of construction of the Craftsman 119.214 item
- rules of operation, control and maintenance of the Craftsman 119.214 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Craftsman 119.214 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Craftsman 119.214, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Craftsman service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Craftsman 119.214.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Craftsman 119.214 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Owner's Manual 10-in. BANDSAW 1/3 HP MOTOR Model 119.214000 CAUTION: Before using this product, read this manual and follow all its Safety Rules and Operating Instructions. • Table of Contents • Full One Year Warranty • Safety Instructions • Assembly • Getting to Know Your Bandsaw • Adjustment • Operation • Maintenance • Trou[...]

  • Page 2

    Table of contents ..................................................................................................................................................................................................... 2 Full one year warranty .............................................................................................................[...]

  • Page 3

    AlwaysWear Proper Apparel. Never wear loose clothing or jewelry that might get caught in moving parts. Rubber-soled footwear is recommended for the best footing. j,_ Always Use Safety Glasses and Wear Hearing Protection. Also use a,face or dust mask if the cutting operation is dusty. Never Overreach. Keep your proper footing and balance at all time[...]

  • Page 4

    1. TOOLS REQUIRED FOR ASSEMBLY Item Description Q'ty. Medium Screwdriver .............................. 1 Adjustable Wrench ................................. t Square ..................................................... 1 LIST OF LOOSE PARTS IN BAG Item Description Q'ty. Blade Tension Knob ............................................ 1 M[...]

  • Page 5

    d. Place the blade tension knob onto the blade tensioner (See Fig. 4). b. Fasten the guide rail with two each star knob screw and washer to the table. Use the hex socket head cap screw, washer and wing nut forcorrecting the working table flatness. (See Fig. 2) FIG. 2 c. Lay the rip fence onto the guide rail. Adjust the rip fence parallel to the saw[...]

  • Page 6

    1. CENTERING THE TABLE a. Loosen the four hex.,bolts mounting the table to the upper table trunnion. (See Fig. 7) FIG, 7 b, Move the table sideways as required, until the saw blade runs through the center of the table insert. c. ft the adjustment of "b" is not enough to center the table, loosen !he four flange nuts holding the lower table[...]

  • Page 7

    a.Remove the rip fence, the guide rail, the wing nut and screw from the table. b.Open the upper and lower doors by tuming the door locking knobs. c. Loosen the blade tension by turning the blade tension knob on the top ofthe upper wheel housing counterclockwise until the saw blade has slackened (viewed from above) (See Fig. 12). c. Set the blade gu[...]

  • Page 8

    d. When the correct adjustment is reached, lock the rear roller guide in position with the guide adjusting screw (D) Fig.16 Guide adjusting screw (C) 9. CHANGING THE DRIVE BELT a. Release the saw blade tension by turning the blade tension knob on the top of bandsaw counterclockwise. b. Using a M6 hex. "L" wrench (not 15rovided) to release[...]

  • Page 9

    Problem Diagnosis Remedy The machine does not work when switched on. 1. No power supply. 2. Defective switch. 3 Defective motor. 1. Check the cable for breakage. 2. Replace the lock switch. 3. Defective motor. The saw blade does not move with the motor running. 1. The blade tension knob has not been tightened. 2. The blade has come off one of the w[...]

  • Page 10

    1N[...]

  • Page 11

    KEYNO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 5O 51 52 53 54 55 56 57 58 59 6O 61 62 63 64 65 66 67 68 69 7O 71 72 73 74 75 76 77 78 79 8O 81 82 DESCRIPTION Door locking knob Cap Hex. Bolt M6x45 Door locking knob body Hex. Nut M6 Slotted Insert Specia[...]

  • Page 12

    Tebla de contenidos ........................................................................................................................................................................................................... 12 Tede el ale con garantia ..................................................................................................[...]

  • Page 13

    ft_l[dl=lni[e];_J Siempre poner le ropa aproplada. Nunca no poner la rope o joyerias que puede agarrar en partes movidas. Caueho-exclusivo de ealzado estd recornendado pare un calzado mejor. _"yl ;,i =1 m [e'] z{e] Slempre uUlizar las gafas de seguridad y poner la protecibn de oido. Tambien utilizar la m_.scara de care o de poLvo sila ope[...]

  • Page 14

    1. Herramienta requerido para el ensamblaje Item Descripci6n Cantldad Destornillador mediano .............................. 1 Llave ajustable .......................................... 1 Cuadrado .................................................. 1 LISTA DE PARTES SUELTOS EN EL PAQUETE Item Descripci6n Cantidad Bot6n de tensi6n de filo ............[...]

  • Page 15

    d, Ubicar bot6n de tension de filo sobre el tensi6n do file (Ver Fig. 4) b. Ajusiar el guia de carril con dos botones de rosca de comienzo y arandear al tablero. Utilizer el bot6n hex puntando el troni[Io, arandelar y balancear para corregir el tablero de trabajo. (Ver Fig. 2) e. Para asegurar la estabilidad vertical suficiente de la maquina este d[...]

  • Page 16

    1. CENTRALIZAR EL TABLERO a. Soltar !os cuatro botones hex mantado en el tablero para el mufi6n de tablero superior. (Ver Fig 7) FIG. 7 b. Mover el tablero de lugar como requerido, haste que sierra de cinta corre atraves del centre del inserci6n de tablero. c. Si el ajustaci6n de "b" no es suficiente al centro de tablero, soltar los cuatr[...]

  • Page 17

    a. Remover la perisca, el caril guiada, el tuerca balanceada y tornillo desde el tablero. b. Abrir las puertas superiors e inferiores per botones de bloqueo de puertas. c. Soltar la tensi6n de file per giro del bot6n de tensi6n de file del ruedecillos superiores con la direciSn de aguja de reloj haste el sierra de file esta fiojo (vet desde arriba)[...]

  • Page 18

    Tornillo de gufa 31equear de ajuste (C) 9. CAMBIO DE CORREA a. Aflojar ta tension de sierra de filo presionando el botOn de tension de s_erra sobre el parte superior de sierra de filo en sentido de aguja de reloj. b. Utilizar una Ilave hex M6. "L" (no suministrado) para aflojar la cabeza de Ilave de encaje sobre el reberde de motor. (Ver [...]

  • Page 19

    Problema Diagnostico Remedio La m&quina no trabaja cuando enciende. 1. No hay suministro de energia 2. Enchufe defectuoso. 3. Motor defectuoso 1. Chequear el cable dafio 2. Reemplazar el enchufe de bloqueo. 3. Motor defectuoso Sierra de cinta no ser_. removido cuando el motor est& corriendo. 1. Bot6n de tensi6n de filo no est& bien ajus[...]

  • Page 20

    Get it fixed, at your home or ours! Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home app[...]