Nortel Networks Passport 8002PS инструкция обслуживания

Part No. 207 314-B April 2000 4401 Gr eat Ame rica Parkway Santa C lara, CA 9505 4 Installing the Passport 8002PS DC Power Supply[...]

ii Copyrig ht © 2000 Nortel Networks All rights reserved. April 2000. The informa tion in thi s do cumen t is sub ject to cha nge withou t notice. Th e st atements, configura tions, techn ical data , and recommen dations i n this docum ent are belie ved to be acc urate and reli abl e, but ar e presented with out express or impli ed warranty . User[...]

iii Japan/Nippon Requirements Only V oluntary Control Council for Interference (VCCI) St atement T aiwan Requir ements Bureau of Standards, Metrology and Inspection (BSMI) Statement Canada Require ments Only Canadian Department of Communications Radio Interference Regulations This digital appara tu s (Passpor t 8002PS DC Power Supp ly) doe s not ex[...]

iv[...]

1 Abou t T his Guid e This guide provid es the follo wing inf ormation: • Safety and environment al guidel ines for th e power s upply (th is page) • Instruct ions for preparin g cables to c onnect to t he power su pply ( page 2 ) • Operationa l note s about th e power supp ly ( pag e 3 ) • Instruct ions for in stalli ng a Passport 8002PS D[...]

2 Prepar ing Ca bles Requir ed tools: Cri mping tool f or crimping l ugs onto ca bles; heat g un Nortel Net works does no t supply t he cables for connecti ng the Passpor t 8002PS DC Power Supply to the DC inpu t power s ource. Y ou can theref ore sel ect cables that co mply wit h the el ectrical code of the country wher e you int end to use t he D[...]

3 Operat ional N otes A Passport 8000 Seri es Chassi s with up to five in stall ed modules can operate with one insta lled power supply . For a redund ant power c onfiguratio n, instal l two power supplies. A Passport 8 010 Chassis with more t han six insta lled modul es requires a minimum of two power supplies for a nonr edu ndant conf igurati on.[...]

4 3. Push the powe r supply pa rtway into th e bay . Leave the t erminal bl ock at th e side of the power supply exposed. 9412F A Note: If you are i nstalling a power suppl y in a new ch assis, be sure to remove the bag of moisture- absorbing mat erial fr om the middle powe r supply b ay . Wa r n i n g : Make sure the DC po wer source is of f or di[...]

5 6. Attach the grounding cable to the system or rack groun d f or your DC i nput powe r source. 7. Firm ly sl id e th e p owe r sup p ly a ll the w a y into th e bay and ti ght en the retai nin g scre ws. 9428F A 8. Attach t he positi ve and nega tive term inal leads t o the DC input power sour ce accordi ng to the p roper saf ety and t echnical s[...]

6 Removing a Power Sup ply Requir ed tools: Phil lips sc rewdriver , 7/1 6-inch wre nch In a chass is with a r edundant p ower supply configura tion, you can r eplace or install a power suppl y without powe ring down th e chassis . 1. T urn of f th e power swit ch on the po wer supply y ou are repla cing. 2. Disable the incomi ng power from th e DC[...]

7 5. Loosen the r etainin g screws on the power supply . 6. Lift the ext ractor l ever to disc onnect the power sup ply from th e backplan e connec tor . Slide t he power su pply partway out of the chas sis. 9431F A 9432FA +DC -DC 7. Disconnec t the pos itiv e and n egati ve v oltag e leads f rom the power supply te rminals. 8. Disconne ct the gr o[...]

8 9. Slide th e power sup ply all t h e way o ut of t he chassis, a nd set it aside. 10. Install a repl acement power supply foll owing the in structions earlier in this guide. If you are not inst alling an other power supply in t his bay , install a filler pa nel over the openin g. 9432F A +DC -DC Specific ations Power Specifica tions Input cu rre[...]