Fisher-Price W1710 инструкция обслуживания

www .fisher -price.com W1710 Please keep this instruction sheet for future reference, as it contains important information. Requires three “AA” (LR6) alkaline batteries (not included) for operation. Adult assembly is required. Required tool: Phillips screwdriver (not included). Wipe with a clean, damp cloth. Do not immerse. This toy has no cons[...]

1 Assembled Parts Upper Ramp Large T ree Canopy T eeter-totter Handle Gate Platform Peek-a-boo Door Flag Base Canopy Swing Hut Roof Wall T ree Lower Ramp Part not shown: Label Sheet C A UTION This product cont ains small par ts in an unassembled st ate. Adult assemb ly is r equired. Base #6 x 5 8 " (1,6 cm) Screw – 3 Shown Actual Size Tighte[...]

2 • T urn the assembly over . • Fit the post on the teeter -totter into the hole in the wall assembly . Hint: Y ou may need to turn the teeter -totter to fit it in place. • Push to “ snap ” in place. • Fit the tree onto the wall. • Lay the assembly face down on a fl at surface and insert a screw into the wall and tighten. 1 2 Assembl[...]

3 • T urn the assembly upright. • Fit the tabs on to the bottom of the wall assembly into the slots in the base. Hint: If the tabs on the wall assembly do not seem to fit, turn it around and tr y again! • Push near each tab to “ snap ” in place. 3 Assembly • At an angle, fi t the peg on one side of the peek-a-boo door into the socket i[...]

4 Assembly • First fi t the tab on the platform into the slot in the backside of the wall A . Then, fi t the upper ramp into the slot in the front of the wall B . • Push to “ snap ” the platform and upper ramp into the wall. 6 Upper Ramp Platform Back View Back View A B • From the back of the wall assembly , fi rst fi t the top of the[...]

5 • Fit the canopy swing onto the outer tree branch, as shown. Push to “ snap ” in place. 8 Canopy Swing • Fit the large tree canopy onto the remaining tree branch. Push to “ snap ” in place. 9 Large T ree Canopy Assembly[...]

6 • Fit the gate into the socket in the base, as shown. Push to “ snap ” in place. 11 Gate • Fit the handle onto the pegs on the wall assembly . • Insert two screws into the handle and tighten. 10 Handle 2 Screws Assembly[...]

7 • Before applying the labels, wipe the sur face with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustration and avoid repositioning the labels. • After applying a label, rub it fi rmly with a clean dry cloth, starting at the center , to remove any air bubbles. Decoration 1 3 2 5 9 8 7 4 6 •[...]

8 • Locate the batter y compartment door on the bottom of the toy . • Loosen the screw in the batter y compartment door and remove it. • Insert three, new “AA” (LR6) alkaline batteries. Hint: We recommend using alkaline batteries for longer battery life. • Replace the batter y compartment door and tighten the screw . Do not over-tighten[...]

9 ICES-003 NMB-003 • This Class B digital apparatus complies with Canadian ICES-003. • Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including inter ference that may cause undesired operation. • Cet appareil numérique de la c[...]

10 PRESS PRESS • Press the lily pad or nest for sounds. Slide the power/volume switch on the bottom of the toy ON with low volume ; ON with high volume ; or OFF . Zoo Fun! • Fit an animal fi gure onto the button on the base. Each animal makes different sounds! • Press down on the ticket booth and the ticket taker will talk to you. PRESS PRES[...]

FCC Statement (United States Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequenc[...]