Pella 812W0100 manual

1
2
3
4
5
6
7
8
9
10
11

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Pella 812W0100, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pella 812W0100 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Pella 812W0100. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Pella 812W0100 should contain:
- informations concerning technical data of Pella 812W0100
- name of the manufacturer and a year of construction of the Pella 812W0100 item
- rules of operation, control and maintenance of the Pella 812W0100 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pella 812W0100 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pella 812W0100, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pella service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pella 812W0100.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Pella 812W0100 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    INST ALLA TION INSTRUCTION - INSTRUCCIONES DE INST ALACIÓN FOR CLAD AWNING, CASEMENT & NON-RECT ANGULAR CASEMENT WINDOW P ARA LAS VENT ANAS DE MADERA RECUBIERT AS DE ALUMINIO TIPO BISAGRAS, BA TIENTE Y BA TIENTE NO-RECT ANGULAR Installation Instructions for T ypical W ood F rame Construction. ese instructions were developed and tested for u[...]

  • Page 2

    YOU WILL NEED T O SUPPL Y : T OOLS REQUIRED: • Cedar or Impervious shims/spacers (12 to 20) • 2" galvanized roong nails (1/4 lb .) • Closed cell foam backer rod/sealant backer (12 to 30 ft.) • P ella ® SmartFlash ™ foil backed butyl window and door ashing tape or equivalent • High quality exterior grade polyurethane or silic[...]

  • Page 3

    E. Apply sill ashing tape #1 . C ut a piece of ashing tape 12" longer than the opening width. Apply at the bottom of the opening as shown (1E) so it o verhangs 1" to the exterior . N ote: e tape is cut 12" longer than the width so that it will extend 6" up each side of the opening. F. T ab the sill ashing tape and fo[...]

  • Page 4

    Interior 2F 2F F. Plumb and square windo w . Place shims 1" from the bottom and top of the window between the window and the sides of the opening. Adjust the shims as required to plumb and squar e the window in the opening. If the frame height exceeds 53", place shims at the midpoint of the window sides. N ote: Do not shim above the windo[...]

  • Page 5

    1 2 0 3 0 4 0 5 0 6 0 7 0 2 3 INCHES mm 2G 2I G. Check the interior reveal . M ake sure the measurement fr om the interior face of the window to the interior face of the wall is equal at several points around the window . N ote: If the dimensions are not equal, check to make sur e the ns ar e folded out to 90° at all points. H. Check window ope[...]

  • Page 6

    3D 3C 3D C. F old down top ap of water r esistive barrier (3C). D. Apply ashing tape to diagonal cuts . C ut pieces of ashing tape at least 1" longer than the diagonal cuts in the water resistive barrier . Apply the tape co vering the entire diagonal cut in the water resistive barrier at both upper corners of the window . N ote: Be su[...]

  • Page 7

    Exterior 3C 3C 3B 3 INTEGRA TING THE WINDOW TO THE WA TER RESISTIVE BARRIER (continued) Curv e T op and Angle T op U nits Only: A. U nits that do not hav e pr e-applied n corners: Cut four pieces of ashing tape 1-1/2" long. A pply one piece of ashing tape to each end of the sill n so that it extends 1-1/2" past the end of the [...]

  • Page 8

    Caution: Ensur e use of low pr essur e polyurethane windo w and door insulating foams and strictly follow the foam manufactur er ’ s r ecommendations for application. Use of high pr essur e foams or improper application of the foam may cause the window frame to bow and hinder oper ation. A. Apply insulating foam sealant . F rom the interior , ins[...]

  • Page 9

    A. Insert backer rod into the space around the windo w approximately 3/8" deep . is should provide at least a 3/8" clearance between the backer rod and the exterior face of the window . N ote: Backer rod adds shape and depth for the sealant line. B. A pply a bead of high quality exterior grade sealant to the entire perimeter of the win[...]

  • Page 10

    INTERIOR FINISHING If products cannot be nished immediately , co ver with clear plastic to protect from dirt, damage and moisture. Remo ve any construction residue before nishing. S and all wood surfaces lightly with 180 grit or ner sandpaper . DO NOT use steel wool. BE CAREFUL NO T TO SCRA T CH THE GLASS. Remove sanding dust. P ella produ[...]

  • Page 11

    INST ALLING ROTO COVER AND CRANK N ote: Finish the interior of the windo w and allow the window to dry before proceeding with these instructions. (T o open the window for nishing, partially insert the lock handle into the jamb, unlock the unit, temporarily attach the crank handle and turn to open.) A. Place the cov er over the operator stud and [...]