Zenoah SRTZ2601F инструкция обслуживания

GB-1 G B SRTZ2601F SRTZ2601F G B OWNER’S MANUAL SHORT REACH TRIMMER 848F4293A1 (705)[...]

GB-2 SRTZ2601F EC DECLARA TION OF COMFORMITY We, ZENOAH CO., L TD. 1-9, Minamidai, Kawagoe, Saitama, Japan declare in sole responsibility that the following products referred to in this declaration conform with DIRECTIVE 89/336/EEC, 98/37/EC, 2000/14/EC, 97/68/EC, 2002/88/EC, 2002/44/EC, prEN774[2001] The products referred are : DESIGNA TION : SHOR[...]

GB-3 G B SRTZ2601F Information This machine is equipped with an Overload Cancellation Mechanism. When the cutting blades have got into metal wires or twigs difficult to cut, the mechanism works as a shock absorber , and protects the gears and the blades from severe reaction which could give damage to those parts. When the blades are frequently caug[...]

GB-4 SRTZ2601F Model SRTZ2601F Overall size (LxWxH) mm 1734 x 338 x 254 Dry weight * kg 6.4 Engine T ype Air -cooled 2-stroke gasoline Model Zenoah GZ25N Max output rpm 1.2Hp (0.9kW) at 7500min -1 Idle speed rpm 3000 ± 200min -1 Displacement cm 3 25.4 Fuel Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil) Carburetor W albro Diaphragm t[...]

GB-5 G B SRTZ2601F 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later when- ever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer fr om whom you purchased the pr od- uc[...]

GB-6 SRTZ2601F W ARNING Never place the throttle into the high-speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting at- tachment stops moving when the throttle is moved fully back to its original position. If it continues to move even after the throttle has been moved fully back, turn off the en[...]

GB-7 G B SRTZ2601F • IF SOMEONE COMES 1. Guard against hazar dous situa- tions at all times. W ar n adults to keep pets and children away fr om the area. Be car eful if you are ap- proached. Injury may result fr om flying debris. 2. If someone calls out or otherwise interrupts you while working, al- ways be sure to turn off the en- gine before tu[...]

GB-8 SRTZ2601F AT T ACHING THE TRIMMING MECHANISM W ARNING The blade has very sharp edges. Be sure to use pro- tective gloves and protective cover whenever han- dling it. 1. Remove the cap on the end of the main pipe. 2. Remove the screw and the fastening bolt scr ewed into the end of the trimming mechanism. 3. Insert the end of the trimming mechan[...]

GB-9 G B SRTZ2601F ■ RECOMMENDED MIXING RA TIO GASOLINE 50 : OIL 1 (when using ZENOAH genuine oil) • Exhaust emission are controlled by the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of any major hardware or the intro- duction of an inert material during combustion. • [...]

GB-10 SRTZ2601F ST ARTING ENGINE 1. Feed fuel into the fuel tank and tighten the cap se- curely . 2. Rest the unit on a flat, firm place. Keep the cutting head off the gr ound and clear of surrounding objects as it will start moving upon star ting of the engine. 3. Push the primer pump several times until overflown fuel flows out in the clear tube.[...]

GB-11 G B SRTZ2601F 8. Operation W ARNING • This product is equipped with extr emely sharp blades, and when used improperly these blades can be ex- tremely danger ous, and improper handling can cause accidents which may in turn lead to serious injur y or death. For this reason, you should always be car eful to follow the following instructions wh[...]

GB-12 SRTZ2601F 9. Maintenance Every Every Ever y 25 50 100 System/components Procedur e Before hours hours hours Note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter , fuel filter inspect/clean ✔✔ r eplace, if necessary see adjusting replace carbur etor idle adjusting screw ✔ idling speed if necessary clean[...]

GB-13 G B SRTZ2601F SP ARK PLUG W ARNING • Do not touch the spark plug with your bare hands immediately after operation, as there is the risk of burns due to high temperature. • After every 50 hours of operation, detach the spark plug and remove dirt from the electr odes with a wire brush or similar . • The correct electr ode gap is 0.6 to 0.[...]

GB-14 SRTZ2601F MUFFLER W ARNING • Inspect periodically , the muffler for loose fasten- ers, any damage or corrosion. If any sign of ex- haust leakage is found, stop using the machine and have it repaired immediately . • Note that failing to do so may result in the engine catching on fire. SP ARK ARRESTER • The muffler is equipped with a spar[...]

GB-15 G B SRTZ2601F Limited warranty Should any failure occur on the pr oduct under normal oper - ating conditions within the applicable warranty period, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: 1 year (6 months if used profession- ally , and 30 days if used for rental purpose) f[...]