Telular SX4e TDMA инструкция обслуживания

06/1 1/02 Part Number 56024002 P HONECELL ® SX4e TDMA 800 MHz V OICE /F AX /D ATA and D IGIT AL T RI -M ODE (TDMA/PCS/AMPS) V OICE /F AX /D ATA T ECHNICAL M ANU AL[...]

SX4e TDMA 800 • SX4e Tri-Mode 2 T echnical Manual Before installing your Phonecell SX4e , carefully remove the unit from the shipping carton and check for evidence of shipping damage. If damage is found, contact your Authorized T elular Distributor or shipping agent immediately . Next, make sure you have the following components: • Phonecell SX[...]

T ABLE OF CONTENTS Safe Operation Instructions ........................................................................................2 Import ant Notices .........................................................................................................2 T echnical Support.....................................................................[...]

SX4e TDMA 800 • SX4e Tri-Mode 4 T echnical Manual INST ALLA TION Antenna Location and Setup The Phonecell SX4e comes with a standard spike antenna - See Figure 1 . The Phonecell SX4e comes with a standard spike antenna (TNC). For optimal signal strength, choose an antenna loca- tion that is above ground and as close to windows (or exterior walls)[...]

SX4e TDMA 800 • SX4e Tri-Mode 5 T echnical Manual Connect Y our SX4e to AC Power 1) A protective earth (safety ground) terminal (screw) marked with this protective earth symbol is provided on the back of the SX4e Phonecell unit. Connect this terminal to a good earth ground (i.e., a cold water pipe) by means of an 18 gauge or heavier insu- lated w[...]

Plug in Y our T elephone 1) Locate the modular line port on your phone and plug in one end of a standard phone cord. 2) Connect the other end of the cord to the telephone port on the side of your SX4e - see Figure 7 . NOTE : An RJ-1 1 connector will fit into the phone port. NOTE : The SX4e does not support direct computer modem (dat a) operation th[...]

SX4e TDMA 800 • SX4e Tri-Mode 7 T echnical Manual HOW TO SET UP YOUR PHONE NUMBER Y our SX4e has been designed for easy setup and inst allation. Y ou can program the Phonecell SX4e with an ordinary tone-dial (DTMF) telephone, which is sometimes referred to as a POTS (Plain Old T elephone Service) phone. Note: This programming mode is not accessib[...]

SX4e TDMA 800 • SX4e Tri-Mode 8 T echnical Manual LED 1 – Power S tatus Indicator LED Color LED Activity Description GREEN Continuous FWT Power ON ORANGE Continuous Low-V oltage Detection NONE (Dark) None No FWT Power LED 2 – Cellular S tatus Indicator LED Color LED Activity Description GREEN Continuous Good Cellular Signal S trength GREEN Fl[...]

SX4e TDMA 800 • SX4e Tri-Mode 9 T echnical Manual Import ant T ones and Alerts No-Service T one – When cellular service is not available, the receiver emits a No-Service (fast- beeping) tone instead of the normal (steady) dial tone. ROH (Receiver Off-Hook) T one – If the telephone equipment remains off-hook (of f its cradle) with no dialing a[...]

SX4e TDMA 800 • SX4e Tri-Mode 10 T echnical Manual Caller ID The Phonecell SX4e sends information to an external Caller ID device to allow presentation of the calling party's telephone number , if this service is available from the network. Caller ID boxes in compliance with ETSI 300 659 or Bellcore GR-30-CORE standards are supported. Only t[...]

SX4e TDMA 800 • SX4e Tri-Mode 11 T echnical Manual Originating Fax and Dat a Calls Sending a Fax Message 1) Set up your fax machine just as you would for a wired telephone line. 2) If your fax machine has a 'prefix' setting, set it to # * 2. If your pro- gram does not have such a setting, add # * 2 to the phone number as shown in the ex[...]

SX4e TDMA 800 • SX4e Tri-Mode 12 T echnical Manual PHONECELL SX4e USER SETUP The SX4e can be programmed with an ordinary telephone, which is sometimes referred to as a POTS (Plain Old T elephone Service) phone. NOTE : The User Setup mode is not accessible while you’re in a call. In the following sections, an <entered value> is comprised o[...]

SX4e TDMA 800 • SX4e Tri-Mode 13 T echnical Manual Enable/Disable Zero Dial Delay for Frequently Called Numbers Use the following key sequence to set the Zero Dial Delay option: Press: # * 21 * <Zero Dial Delay option> # Enter : 0 to disable Zero Dial Delay option 1 to enable Zero Dial Delay option. Enter either 0 or 1; otherwise the Phonec[...]

SX4e TDMA 800 • SX4e Tri-Mode 14 T echnical Manual PHONECELL SX4e TECHNICIAN PROGRAMMING COMMANDS How to Enter the T echnician Programming Mode Use the following access code to enter the T echnician Programming mode: Press: # * 0 * 1 2 3 4 4 3 2 1 # The access code is 8 digits. If the access code is not 8 digits or does not match the access code,[...]

SX4e TDMA 800 • SX4e Tri-Mode 15 T echnical Manual Roam Option The following key sequence is used to enter the roam option: Press: # * 6 * <home only> * <SOC disable> # When the home only value is set to 0, the Phonecell will use the SOC/SID list specified in the IRDB along with the home SID and home SOC when searching for service, an[...]

SX4e TDMA 800 • SX4e Tri-Mode 16 T echnical Manual Call-Answered Supervision Pulse Option The following key sequence is used to enable or disable the call-answered supervision pulse, select its frequency , and program its duration: Press: # * 18 * <cas_pls_enable> * <cas_pls_freq> * <cas_pls_duration> * <cas_pls_level> # T[...]

SX4e TDMA 800 • SX4e Tri-Mode 17 T echnical Manual Ring Back request The following key sequence is used to request immediate ring back: Press: # * 13 * # There is no ring back value to be set; the command activates when the phone is placed back on- hook. Restore Factory Default s Request The following key sequence is used to request restoration o[...]

SX4e TDMA 800 • SX4e Tri-Mode 18 T echnical Manual Primary B-Side Non-St andard Control Channel Option The following key sequence is used to select the non-standard primary control channel range for B- side AMPS systems: Press: # * 90 * <first ACC> * <last ACC> # The first ACC and last ACC values must be in the range of 0-799 or 991-1[...]

SX4e TDMA 800 • SX4e Tri-Mode 19 T echnical Manual PHONECELL SX4e TROUBLESHOOTING T elephone Service is Not Working If the telephone service is not working, first check the operation of the telephone equipment and wiring connected to your Phonecell. T est the equipment on a different service or piece of equipment to ensure proper operation, or co[...]

SX4e TDMA 800 • SX4e Tri-Mode 20 T echnical Manual GENERAL INFORMA TION AND SAFETY T emperature Environment Operating T emperature: From -10°C (14°F) to +50°C (122°F); Up to 95% relative humidity (non-condensing) Storage T emperature: From -20°C (-4°F) to +60°C (140°F); Up to 95% relative humidity (non-condensing) Y our Phonecell SX4e FWT[...]

SX4e TDMA 800 • SX4e Tri-Mode 21 T echnical Manual Aircraf t T urn OFF your Phonecell SX4e before boarding any aircraft. • Use it on the ground only with crew permission. • Do not use it in the air . T o prevent possible interference with aircraft systems, U.S. Federal Aviation Administration (F AA) regulations require you to have permission [...]

SX4e TDMA 800 • SX4e Tri-Mode 22 T echnical Manual IMPORT ANT NOTICES - CONTINUED WARRANTY I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: TELULAR CORPORA TION ('T elular") warrants to a distributor Buyer , or to a customer only if the customer is a Buyer direct- ly from T elular, that the Products (including accessories) shall comply wi[...]

SX4e TDMA 800 • SX4e Tri-Mode 23 T echnical Manual V. GENERAL PROVISIONS: THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS OR STATUTORY WARRANTIES. IMPLIED WAR- RANTIES, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, INFRINGEMENT, DELIVERY, NEGLIGENCE AND PERSONAL INJURY, ARE DIS- C[...]

06/1 1/02 Part Number 56024002 647 North Lakeview Parkway V ernon Hills, Illinois 60061, USA USA: 1-800-TELULAR (1-800-835-8527) T el: 847-247-9400 • Fax: 847-247-0021 E-mail: support@telular .com http://www .telular .com[...]