Moog Videolarm WS2C-50NA инструкция обслуживания

PR ODUCT INSTR UCTIONS INST ALLA TION PREP ARA TION 1. Determine the mounting location. Be sure that you'll be mounting to a secure wall or ceiling. W e also recommend that for outdoor applications the housing be mounted in a protected area. 2. Complete all wire and conduit runs prior to installation. 3. The WS2 and WS4 are designed to be moun[...]

- 2 - CAMERA BRA CKET SETUP (Figure 5) Reattach the brack et assembly to the back bo x using the two 10-32 x 3/8" screws . NO TE: For ceiling mount applications do not fully tighten immediately . Figure 2 1. Connect the output of your Class 2 P ower Supply to the terminal connectors on the PC Board inside the housing. Refer to the T roubleshoo[...]

- 3 - Figure 6 CAMERA FOCUSING Fixed Lens: Loosen the set screw in the lens mount and to manually rotate the lens until a clear picture is achie ved. Once the focus is set, retighten the set scre w (Figure 6). Set screw Fixed lens V ari-Focal Lens: First, adjust the Magnifi cation Lock Screw to the desired magnifi cation (telephoto to wide angle)[...]

- 4 - The operational settings f or the camera are defi ned by ten dip switches located on the PC Board (Figure 9). Moving the switches to the on position will activate each setting. Factory defaults are pictured below (Figure 10 and 11). F A CT OR Y DEF A UL T FIXED AND FIXED V ARI-FOCAL LENSES: Dip Switches 5 and 7 on, all others off. Figure 10 [...]

- 5 - NO TE: This hi-res color camera uses a 1/4" chip and a 3-6mm auto iris lens. It is comparable to a 1/3" chip using a 4-9mm auto iris lens. The operational settings are defi ned by f our dip switches located on the side of the PC Board (Figure 12 and 13). Moving the switches to the UP position will activate specifi c settings. Refe[...]

- 6 - Wiring Notes Wire — What to DO 1. DO use point-to-point Unshielded T wisted P air wire, gauge 24 or thick er , stranded or solid, Categor y 2, 3, 4, or 5. 2. The video signal may co-e xist in the same wire bundle as other video , telephone, data, control signals , or low-v oltage power . It is also OK to run NVT video signals in or near ele[...]

250 ft 250 ft 3 4 5 8 13 1 300 ft 300 ft 4 5 6 10 16 1 400 ft 400 ft 5 6 8 13 21 1 500 ft 500 ft 6 8 10 16 26 1 600 ft 600 ft 8 10 12 19 31 1 800 ft 800 ft 10 13 16 25 42 1 1 0 0 0 f t 13 16 20 32 52 1 1 2 5 0 f t 16 20 25 40 65 1 1 5 0 0 f t 19 24 30 48 78 1 1 7 5 0 f t 23 28 35 55 91 1 2 0 0 0 f t 26 32 40 63 104 1 2 5 0 0 f t 32 40 49 79 131 1 3[...]

! CAUTION RISK OF ELECTRIC SHOCK! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE. SAFETY PRECAUTIONS IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read befor e the unit is operated. 2. Retain Instructions - The safety and operating instructions should [...]

P ower Supply P ower A P ower B Camera Assembly Primar y Po w e r Video Signal Video Shield Monitor - 10 - (Ground Return) Figure A Ground Loop TR OUBLESHOO TING If you e xper ience problems with the camera picture please chec k these simple troubleshooting procedures f or possible solutions before calling technical suppor t. IMPORT ANT NO TE: If y[...]

AC V oltmeter Camera Monitor Bridge Tap NV-213 A NV-213 A - 11 - NVT TROUBLESHOO TING If you are e xper iencing problems , attempt to simplify your setup . T est each cable segment separately . F or example , test the camera and monitor together without the other equipment. Then add in the NVT transceiv ers, bac k-to-back. T est each segment of a l[...]

- 12 - Depending on the voltage being used, ref er to one of the formulas below to select the correct pow er supply for camer as connected in parallel (positive to positiv e, negative to negativ e): T otal current for a 12 VDC system: T O T AL CURRENT = (350mA x total number of cameras) Example: 350mA x 5 total cameras = 1750mA T otal current for a[...]

6 5 4 3 2 1 7 - 13 - WS2 - Exploded Diagram[...]

- 14 - WS2 - Replacement P ar ts List Part Number Description 1 RPWS2010 W ARRIOR 2 & 4 BASE ASSEMBL Y 2 RPWS2020 W ARRIOR 2 & 4 CARRIAGE ASSEMBL Y KIT NTSC BOARD CAMERAS 3 RPWS1041F W ARRIOR 1 & 2 ST ANDARD RES, BLACK & WHITE, FIXED CAMERA KIT RPWS1041V WARRIOR 1 & 2 ST ANDARD RES, BLACK & WHITE, V ARIFOCAL CAMERA KIT RPWS1[...]

7 6 5 4 3 2 1 - 15 - WS4 - Exploded Diagram[...]

- 16 - WS4 - Replacement P ar ts List Part Number Description 1 RPWS2010 W ARRIOR 2 & 4 BASE ASSEMBL Y 2 RPWS2020 W ARRIOR 2 & 4 CARRIAGE ASSEMBL Y KIT NTSC BOARD CAMERAS 3 RPWS3041F W ARRIOR 3 & 4 ST ANDARD RES, BLACK & WHITE, FIXED CAMERA KIT RPWS3041V W ARRIOR 3 & 4 ST ANDARD RES, BLACK & WHITE, V ARIFOCAL CAMERA KIT RPWS[...]

Pr oduct Registr ation / W arr anty Thank y ou f or choosing Videolarm. W e value y our patr onage and ar e solely committ ed to pr oviding y ou with only the highest quality pr oducts av ailable with unmatched customer service lev els that ar e second-t o-none in the security industr y . Should a pr oblem arise, r est assure that Videolarm stands [...]