Meridian Audio LD100/LD100U инструкция обслуживания

The Far oudja LD100/LD100U Line Doubler Installation & Operation Instructions[...]

History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Licensees and Awards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Inventory List . . . . . . .[...]

HISTOR Y Faroudja Laboratories, located in northern Califor- nia’ s Silicon V alley , was founded in 1971 by Y ves and Isabell Faroudja to develop state-of-the-art of video processing technology . Over the last 20 years, Faroudja Laboratories and its companion R&D center , Faroudja Resear ch, have indeed devel- oped hundreds of advanced elect[...]

LICENSEES AND AW ARDS 1987: SMPTE DA VID SARNOFF GOLD MEDAL AW ARD for “Contributing in Optimizing NTSC Performances” 1988: MONITOR AW ARD for “Excellence in Engineering NTSC Encoders and Decoders” 1989: BM/E AW ARD for “Excellence in Engineering” 1991: T echnology Executive of the Y ear from Cable TV Business 1991: EMMY from The Nation[...]

The Faroudja System LD100 digital scan converter is a precision video instrument used to convert NTSC Composite, Y/C, or 525 line RGB or Component interlaced signals into 525 line progr es- sive outputs. Using the LD100 digital scan converter will produce pictur es with more details, r emove unwanted picture artifacts and, when used with pr o- ject[...]

Circuit Description Figure 1 is a block diagram of the LD100 showing signal flow and the location of front panel contr ols and switches. Composite Video and Y/C (S-VHS) inputs are connected to the units decoder with AGC control and converted to Y , R-Y and B-Y signals. The Y , (Luminance) output from the decoder enters the input switcher while the [...]

LD100 TECHNICAL HIGHLIGHTS – The LD100 is far more than simply a “line doubler”. It is a truly unique pr oduct in the world of high performance video. The LD100 is actually a complex image processor that consists of thr ee distinct components – all utilizing patented Faroudja technologies and engineer ed into one chassis; the SuperNTSC deco[...]

7 on two differ ent mechanisms. Horizontal resolution is a function of bandwidth (frequency r esponse) of the circuitry while vertical resolution is a function of the scanning fr e- quency (the number of scan lines in each picture). Given these mechanisms and the average size picture tube being 8-10”, they designed the 525 line broadcast stan- da[...]

Unpacking Remove the LD100/LD100U from the shipping container and examine it for any signs of shipping damage or missing items, (check inventory list on page 5). All shipping materials should be saved if the unit is to be moved or should need to be returned for service or repair . Installation The LD100/LD100U is designed to be placed on the table [...]

15. Sync T ermination Switch – Select ON when 15. not looping the Composite Sync signal to other video devices, (75 Ohm). 16. Sync Input Loop (BNC) – Composite Sync Input Loop 17. Sync Input (BNC) – Composite Sync Input 18. Red Output (BNC) – Red Output 714mV 19. Green Output (BNC) – Gr een Output 714mV 20. Blue Output (BNC) – Blue Outp[...]

The LD100 Control panel Selecting a push button control lights the adjacent LED to indicate activation or selection of that partic- ular function. 1) Power ON/OFF – Press the button and the LED lights green to indicate POWER ON. When the LD100 powers up it is automatically set to oper- ate just as it was when it was last turned off. The Detail En[...]

6) Brightness Level – Known as “Set-up” in the broadcast industry , the BRIGHTNESS control is used to set up the background black level. Pull the knob out and turn fully counter clockwise until the picture goes dark. Then r otate the con- trol clockwise until the black ar eas in the picture just begin to go gray . T urn the control back count[...]

Problem Solution No power light Unit not turned on Unit not plugged in Fuse blown No power at plug No picture Video source not selected No video source connected or operating Projector/Monitor not turned on Projector/Monitor not connected corr ectly Bad video cable Unit in freeze mode Check brightness and contrast levels Colors bleeding Check LD100[...]

Overview Remote control of the LD100 / LD100U Line Doubler is provided by an RS-232 serial interface connector located on the rear panel of the unit. A external controller such as a computer or integrated system controller with an RS-232 interface may be used to control all user accessible functions of the Line Doubler . RS-232 controllable functio[...]

Command Line The LD100 is programmed by means of a “Command Line”, which is an ASCII string of up to 255 characters that contains one or more individual instructions to the LD100. The Command Line offers the best compr omise between manual opera- tion via a data terminal and automatic control via a controller . Command Line Entry A Command Line[...]

ST or st This command will return a string showing the current settings of the LD100. Example: HELP or help This command will return a list of commands used for the LD100 Line Doubler . LD100 Local / Remote Operation The LD100 stores all of it’ s settings in a Non-volatile ram and will return to the last known settings when the unit is power up. [...]

Cable Lengths and Distribution Amplifiers To aid in achieving the bet r esults from your installa- tion, we suggest the following minimum standards for cable runs when an LD100 is used. To pr eserve the video quality of the LD100, the signal path should be no more than –3db down at 25 MHz through a 75 ohm cable. Any distribution amplifier should [...]

17 SPECIFICA TIONS LD100 Specifications INPUT SIGNALS (NTSC) 525 Line 2:1 Interlace Video 1Vp-p, Negative Sync 714mV Luminance Y/C Y/C (3.58) Non-Composite 700m/Vp-p Y 286mVp-p C (Burst) RGB 700mVp-p Non-Composite, 1Vp-p Composite Component Y(1V w/Sync), R-Y(714mV), B-Y(714mV) Composite Sync Negative, > 4Vp-p Composite OUTPUT SIGNALS (NTSC) 525 [...]

W ARRANTY INFORMA TION All F AROUDJA Laboratories products ar e warranted to the original purchase against defective materials and workmanship under normal use and service for a period of one (1) year from the date of shipment. This warranty shall be of no for ce and effects if mod- ifications have been made by the purchaser or its agents or employ[...]