Interquartz 98583 инструкция обслуживания

LCD FEATURE PHONE Model 98583 OPERATING INSTRUCTIONS[...]

1 This Interquartz telephone has been manufactured to very high standards and is very easy to use. Please read this manual carefully to find out how to use the features. Contents 1. Important Notes ..................................................................................... 2 Intended use ...................................................[...]

2 1. Important Notes Intended use This apparatus is intended for use on 2 wire analogue PSTN and P ABX circuits within the United Kingdom. Declaration of Conformity I nterquartz (UK) Limited declares under its sole responsibility that this product Model: 98583 Is in conformity with the following relevant harmonised standards Health & Safety 73/[...]

3 REN number The REN number of this telephone is 1. If you wish to connect any other equipment to the line, simply add the REN numbers of each piece together and ensure that the total does not exceed 4. If too many phones are connected to the line, the circuit may be overloaded and your telephone may not ring. Not all telephones have the same REN. [...]

4 2. Installation This telephone is designed to plug straight into a modular style socket. If you do not have one of these sockets, they can be obtained from your Network Supplier . A card is included for this purpose. Simply complete it and send it to your Network Supplier . Batteries This telephone requires 4 AA battery cells ( provided separatel[...]

5 Connection Insert the line cord into the socket. Set the tone/pulse switch ( located in the base of the telephone, see Figure 2 ) to the appropriate position. If you are unsure as to whether your exchange is pulse or tone, call your Network Supplier and they will advise you. Set the ringer volume and ringer pitch control, as desired. Setting the [...]

6 MESSAGE WAITING POLARITY SWITCH 3. T elephone Features Liquid crystal display (LCD) The LCD displays up to 16 numbers to show the time of day , the duration of call time or the number being called. In addition, there are ten prompts that appear at the top of the display to indicate different modes of operation of the telephone. Handsfree button P[...]

7 Mute button Press to activate the mute circuit, cutting off the speech transmission to the handset ( or handsfree microphone ). Press again to resume normal conversation. The red LED, below the mute button, glows when the call is muted and a MUTE prompt is also displayed on the LCD. Note : The MUTE function will only operate in the on-line state [...]

8 Start / Stop Push to start the timer , push again to stop it. Note, the timer will automatically start when the telephone handset is lifted (or the handsfree button is pressed) and will stop when the handset is replaced. The elapsed time will show on the LCD for a period of 8 seconds and then the display will revert to clock. T one button This bu[...]

9 Pause button Introduces a pause of 3.6 seconds during dialling. A maximum of 3 pauses may be inserted, otherwise the telephone may cease to function properly . This feature is storable in memory . Store button Used for storing numbers in the direct access memories. The numbers 0 to 9, *, #, handsfree, on/of f hook, pause and TBR recall can be sto[...]

10 Ringer pitch control Located on the base of the unit ( see Figure 2 ). Rotating this knob alters the pitch of the ringing signal. Ideal where there is more than one phone in a room. V olume slider Adjusts the volume of the on-hook dial / handsfree speaker . T one / Pulse switch Located on the base of the unit ( see Figure 2 ). Used to select the[...]

11 4. Operating Instructions Manual dialling Lift the handset, listen for the dial tone and then dial the required number using the keypad. The number called will appear on the LCD. On hook dialling In this mode, telephone calls can be made without lifting the handset and the progress of calls can be monitored. Once the calling party answers the ph[...]

12 Speakerphone dialling The speakerphone can be used for manual dialling in much the same way as the off-hook dialling method : - Press the speakerphone button and the dial tone will be heard in the speaker . - Dial the required number on the keypad - When the called party answers the phone, continue to speak using the microphone in the telephone [...]

13 When using the memory facilities, this telephone has two audible beeps to advise you of a correct entry - "high tone" or an incorrect entry - "low tone". If you make an incorrect entry , check your error and re-input the information. When entering numbers into these direct access memories you should ensure that you have progr[...]

14 The memories are capable of storing the numbers 0-9, #, *, pause, tone, timed break recall, off-hook, handsfree. If a number in memory begins with an of f-hook or a speakerphone code, the associated button becomes a speed dialling button. Pressing the button will turn on the monitor in either handsfree or speakerphone mode. The dial tone will be[...]

15 Cascade dialling It is possible to dial a number that is contained in more than one memory location or for which you want to dial part of the number manually . e.g. for a very long number split between memory locations 1 and 2 - obtain a dial tone - press memory button 1 - press memory button 2 the telephone will now dial a number consisting of [...]

16 It is possible to store mixed dialling format numbers in the memory . Simply follow the above procedure, pressing the tone key at the appropriate place. Redialling The telephone number stored in the temporary re-dial buf fer will NOT include the of f-hook or the Speakerphone codes if these were input manually before a call was made. Simple redia[...]

17 5. P ABX and System Usage This telephone can be used behind a P ABX or on a network system that utilises the recall function. There are many such systems and whilst it is likely that no problems will be encountered, it cannot be guaranteed that the telephone will operate correctly under all circumstances and any cases of difficulty should be ref[...]

18 Automatic pause insertion If your P ABX requires a pause after dialling the outside line access code, this can be inserted automatically by programming the telephone. e.g. If the access code is "9", the telephone can be programmed in the following way - press store - press "9" - press store - press " * " Whenever a [...]

19 If for some reason the message light, a bright red LED, comes on with NO message signals received, remove the telephone from the line and adjust the switch marked S1/S2 from the S1 position to the S2 position. When re- connected, the telephone should now function correctly . It must be pointed out that various P ABX types have individual system [...]

20 6. Maintenance and Problem Solving Y our telephone is a precision electronic instrument. Avoid rough handling and extreme temperatures. Use a mild detergent and a damp cloth when cleaning. Never use a stronger cleaner . If your telephone does not appear to be working correctly , please check the following : No dial tone - is phone cord properly [...]

21 7. W arranty and Service This product is guaranteed, by Interquartz (UK) Limited, for six years from the date of manufacture. Every Interquartz telephone has a unique serial number and part of that number refers to the date of manufacture. A label, similar to that shown below is affixed to each telephone 9515 030852 (model no) QC.P The figure 95[...]

Distributed in the United Kingdom by Interquartz (UK) Limited Manufactured by International Quartz Limited A Subsidiary of Chiaphua Industries Ltd. © Copyright INTERNATIONAL QUARTZ LTD. 2000 3C58301SXAQ12B If you need to return a faulty unit to us, send it to : Interquartz (UK) Limited Pennine House Salford Street Bury BL9 6Y A Make sure that you [...]