Royal G31 manual

0102 095 50261 6/,0/,1(67$1'$5' USERS INSTRUCTIONS THIS CAT I 3P APPLIANCE IS FOR USE ON PROPANE GAS G31 AT A SUPPLY PRESSURE OF 37 mbar IN GB & IE HAND THESE INSTRUCTIONS TO THE USER DESCRI PTI ON[...]

This Royal Cozy Fires Decorative Fuel Effect gas fire has been developed to give a realist ic coal burning appearance with the instant control and convenience of g as. The fire has been constructed to enable it to be installed into applications where the warmth and comfort of an open fire and hig h radiant heat is required. This appliance is intend[...]

One ty pe of fire front and fret sugg ested is shown in Fig 1, this has a perforated fret to allow air to be drawn into the coal bed for combustion and over the controls for cooling purposes. I f other fronts and frets are to be used they must have a minimum open area in the fret of 20 sq. cms and 60 sq. cms in the front. See Fig 1 This appliance i[...]

It is very important that the coals and the coal bed components are laid as shown no extra coals or material may be used. I f any of the items become lost or damaged, replacements must be obtained before further use of th e appliance. Relaying the Coal Bed Fit the coal support shelf (ensuring that the front edge sits behind the three tabs) and the [...]

Page 4 Page 5[...]

REGI STRATI ON RECORD Purchaser’ s Name__________________________________________________ and Address __________________________________________________ __________________________________________________ Supplier’ s Name __________________________________________________ and Address __________________________________________________ ___________[...]

0102 095 50251 6/,0/,1(67$1'$5' INSTALLATION and SERVICING INSTRUCTIONS THIS CAT I 3P APPLIANCE IS FOR USE ON PROPANE GAS G31 AT A SUPPLY PRESSURE OF 37 mbar IN GB & IE HAND THESE INSTRUCTIONS TO THE USER[...]

DESCRIPTION This Roy al Cozy Fi res Decorative Fuel Effect gas fire has been developed to give a realisti c coal burning appearance with the instant control and convenience of gas. The fire has been constructed to enable it to be installed into applications where the warmth and comfort of an open fire and high radiant heat is required. This applian[...]

Installation Regulation and Requirements The appliance must be installed by a competent person in accordance with the current Gas S afety (I nstall atio n and Use) Regulations 1994 (as amended) or the rules in force and in accordance with the manufacturers instructions, failure to do so could lead to prosecution. The following ar e the re leva nt C[...]

Fire Surround and Opening Requirements Check that the chimney and flue structure are sound and conform to the following flue requirements: a) A conventional brick or stone chimney with a minimum effective cross sectional dimension of 225x225mm. A lined flue with a minimum diameter of 175mm having a chairbrick and throat forming lintel conforming to[...]

Installation of the Appliance Check tha t the chimney conforms to the required specific ations as previously stated. Examine the condition and carry out any remedial work as necessary , if the flue has been used for solid fuel it should be swept and a smoke test carried out to check that sat isfactory smoke clearance has been established. If all th[...]

Installing the Appliance in Position When the ga s supply pipe has been laid to the position required, the surround should be fitted and sealed to the chimney correctly. This is to prevent any seepage of flue products or to prevent any ingress of air into the flue from any where other than the flue outlet of the fire. The easier method of installat[...]

To check the gas pressure at the appliance, allow the coals and the coal bed to cool and turn off the g as supply at the isolating cock. Remove the hexagon headed screw and connect a manometer to the pressure test point, turn on the g as and ignite the fire, allow to heat up and check that the gas pressure is 37 mbar +/ - 1 mbar - any appreciable d[...]

Maintenan ce and S ervicing GENERAL A. REMOVAL OF DEBRIS OR SOOT DEPOSITS Allow the appliance to cool sufficiently before removing all of the coals and firebed components for cleaning purposes. Once all the cerami cs are removed from the firebed check that no debris is locat ed in the burner slots (both front and rear). If any debris is present it [...]

Page 9[...]

Page 10[...]

Page 11[...]

[...]

Page 12[...]

Page 13[...]

Page 14 No Figures 13 & 15 On this page[...]

Registration Record Purchasers Name ....................................................................................... and Address ....................................................................................... ....................................................................................... ......................................[...]