Royal U19019 G20 manual

81139 Issue 3 52<$/&+(/7(1+$0 USERS INSTRU CTIONS THIS CAT I 2H APPLIANCE IS FOR USE ON NATURA L GAS G20 AT A SUPPLY PRESSURE OF 20 mbar GB and IE HAND THESE INSTRUCT IO NS TO THE USER[...]

DESCRIPTION The Royal Cheltenham glass fronted high efficiency live fuel effect inset gas fire has been developed from the successful Roy al Cozy fires LFE using much of the techno logy and components used in the manufact ure of this appliance. The fuel bed has a reali stic coal effect util izing ceramic ‘coals’ and coal bed that allows seconda[...]

TECHNICA L DATA Heats I nput Rates: High Setting 5.42 kW 18,500 Btu/h (Gros s) Low Setting 2.34 kW 8,000 Btu/ h This fire will run for 5.4 hour s on one therm of g a s on hig h setti ng . LOCATION OF COM BU S TI BL E SHE LV ES ABOVE F IRE SIDE OF F IRE Min. Height of 150 mm deep she lf Min. Dimensi on fro m ou ter edg e of fire above hearth = 830m [...]

DISMANTLING THE F IRE BED FOR CLEANING (see fig.3, 4 & 5) Allow the appl iance to cool for 1 hour before handling an y components. Remove the controls cover and unscrew the two wing screws securi ng the canopy in place as shown in (fig 3). L ift the canopy off the appliance and place to one side. Support the glass panel a nd remove the four win[...]

COAL LAYING INSTRUCTION S Lay the four front coals diagonally with the stepped corner sit ting on the sim ulated coal front and the small corner notch at the rear. L a y a further row of fo ur coal s behind the fro nt r ow with stepped corners in the rear corners of the front row, the two centre coals having no t ches in the rear top corners. L a y[...]

Note: Should any ‘coals’ or the coal bed become damaged, lost or broken, only the correct replacem en ts must be obtained and fit ted before the appl iance is used. E x tra ‘coals’ etc. must not be added to the coal bed. The coal bed must alway s be assemb led as detai led. This a ppliance is fitted with an Oxy /pilot the purpose of wh ich [...]

REGI STRATI ON RECORD Purchaser’ s Name ______________ ____ ____ ____ ____ ____ ____ _____ ___ ____ and Address ______________ ____ ____ ____ ____ ____ ____ _____ ___ ____ ______________ ____ ____ ____ ____ ____ ____ _____ ___ ____ Supplier’ s Name ______________ ____ ____ ____ ____ ____ ____ _____ ___ ____ and Address ______________ ____ ____ [...]

81140 Issue 3 52<$/&+(/7(1+$0 INSTALLATION AND SERVICING INSTRUCTIONS THIS CAT I 2H APPLIANCE IS FOR USE ON NATURAL GAS G20 AT A SUPPLY PRESSURE OF 20 mbar GB and IE HAND THESE INSTRUCTIONS TO THE USER[...]

DESCRIPTION The Roy al Chelt enham g l ass fronted high efficiency liv e fuel effect inset gas fire has been developed from the successful Roy a l Cozy fires. The fuel bed has a realistic coal effect utilising ceramic ‘c oals’ and coal bed that allows secondary air to be entrained into the bed for clean combustion, the burner is an aerated twin[...]

INSTALLATION REGULATIONS AND REQUIREMENTS I n the interests of both the Law and of Safety , this appliance must only be installed by a competent person in accordance with the current Gas S afety (Installation and Use) Regulations or t he rules in force and t he manufacturer’ s instructions. Note: Failure to install a g as appliance correctly coul[...]

Page 4 Clearance to side (tim ber surrounds etc .) Minimum cl earance required to any combustible materia l to the side of the appliance must be 150mm. Clearance to shelves. Minimum clearances t o undersides of a 150mm deep combustible shelf from the hearth must be 830mm. Add 12.5mm to this clearance for every 25mm increase in depth of shelf.[...]

Page 5[...]

INSTALLATION USING A 5" DIAMETER METAL F LUE BOX Page 6 Important: The Flue restrictor pl ate must be removed see F ig 10. When the metal flue box is to be built-in as a false chimney breast using timber stud work with plasterboard fa cing, the flue box should be enveloped with insulation material such as rockwool or similar to prevent a build[...]

INSTALLATION OF THE APP LIANCE Check that th e chimney conform s to the required specificati ons as previously stated. Ex amine the condition and carry out any remedial work, if the flue has been used for solid fuel it should be swept and a smoke test carried out to check that sati sfactory smoke clearance has been established. If all the smoke is [...]

Page 7 a (ii) If the spacer frame is to be used, attach the fram e to the rear of the appliance using either the screws and captive nuts removed from the appliance or supplied in the fixing kit, see fig 8. Place the fire in the required position; mark around the perimeter of the spacer frame remove the appliance and the spacer frame from the applia[...]

Page 8[...]

Page 9[...]

Page 10[...]

Page 11[...]

Page 12[...]

CHECKING OP ERATION OF F IRE Purge the air from the appliance by rotating the control to the ig nition position, push the control to allow the air in the pipework to be purged, push the piezo to ignite the Oxy /pilot. Check that the electrode is sparking between the tip of the thermocouple and continue until a pilot flame has been established. Depr[...]

Complete the registration section at the end of this booklet. Advise that any component part of this appliance be guaranteed ag ainst defective workmanship or faulty materials for a period of twelve months from the date of purchase. Any such part will be replaced free of charge on receipt of the purchaser’ s address at the cost of postage only , [...]

Page 15[...]

SHORT PA RTS LIST For spares contact the manufacturer at the address overleaf. DESCRIPTI ON CROSSLEE No GC No Piezo Ig niter 40245 397 686 Control Knob 40232 170 014 Control Valve 42143 378 092 Oxy/Pilot B urner Assembly 42313 170 415 Main I njector 42168 378 090 Complete Coal & Fibre Pack 42203 REGI STRATI ON RECORD Purchaser’ s Name ……?[...]