Makita RP1101 manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Router MODEL RP1100/RP1101 003650[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA001-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 SER VICE 23. T ool ser vice m ust be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to[...]

5 An adapter Fig. “B” and “C” is av ailable f or connecting Fig. “A” type plugs to two- prong receptacles. The g reen-colored r igid ear , lug, etc., e xtending from the adapter must be con- nected to a permanent ground, such as a proper ly g rounded outlet box. SPECIFIC SAFETY R ULES USB013-3 DO NO T let comf or t or familiarity with p[...]

6 13. Do not touch the bit immediately after operation; it may be e xtremely hot and could burn y our skin. 14. Alwa ys lead the power supply cord a way from the tool to wards the rear . 15. Do not smear the tool base carelessly with thinner , gasoline, oil or the like. They may cause cracks in the tool base. 16. Draw attention to the need to use c[...]

7 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Adjusting the depth of cut Place the tool on a flat surf ace. Press the lock le ver do wn and lowe r the tool body until the bit just touches the flat sur- f ace. Release the lock le ver to hold the [...]

8 CA UTION: • Since e xcessive cutting ma y cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than 15 mm (9/16 ” ) at a pass when cutting groov es with an 8 mm (5/16 ” ) diameter bit. • When cutting groov es with a 20 mm (13/16 ” ) diameter bit, the depth of cut should not be more than [...]

9 Speed adjusting dial For model RP1101 only The tool speed can be changed by turning the speed adjust- ing dial to a given n umber setting from 1 to 6. Higher speed is obtained when the dial is turned in the direc- tion of number 6. And low er speed is obtained when it is turned in the direction of number 1. This allows the ideal speed to be selec[...]

10 Inser t the bit all the wa y into the collet chuck and withdra w it very slightly ( approx. 2mm;1/16 ” ). Then tighten the collet chuck securely with the two wrenches . These routers accommodate the bits with 1/2 ” diameter shank. When using the 1/4 ” diameter shank bit, replace the equipped collet chuck with the one f or 1/4 ” diameter [...]

11 • When using the straight guide, be sure to install it on the right side in the feed direction. This will help to k eep it flush with the side of the workpiece. Straight guide (optional accessory) The straight guide is eff ectively used f or straight cuts when chamfe r ing or groo ving. T o install the straight guide, inser t the guide bars in[...]

12 T o install the templet guide, inser t the templet guide in center hole in the base plate and secure in place with the lock n ut. Secure the templet to the workpiece. Place the tool on the templet and mov e the tool with the templet guide sliding along the side of the templet. MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched o[...]

13 Use a screwdriv er to remove the brush holder caps. T ake out the worn carbon br ushes , inser t the new ones and secure the brush holder caps. T o maintain product SAFETY and RELIABILITY , repairs, any other maintenance or adjustment should be perf or med by Makita A uthor iz ed or F actor y Ser vice Centers , always using Makita replacement pa[...]

Memo 14[...]

Memo 15[...]

Memo 16[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This product was pur chased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]