Go to page of
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Pelco WLV2500, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pelco WLV2500 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Pelco WLV2500. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Pelco WLV2500 should contain:
- informations concerning technical data of Pelco WLV2500
- name of the manufacturer and a year of construction of the Pelco WLV2500 item
- rules of operation, control and maintenance of the Pelco WLV2500 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pelco WLV2500 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pelco WLV2500, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pelco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pelco WLV2500.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Pelco WLV2500 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
® P elco • 3500 Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981 FAX (800) 289-9150 or (1-559) 292-3827 WL V2500 Series Wir eless Control Link and V ideo T ransmission Systems Installation/Operation Manual C914M (7/96)[...]
-
Page 2
ii Pelco Manual C914M (7/96) ®Pelco and the Pelco logo are registered trademarks of Pelco. ©Copyright 1996, Pelco. All rights reserved. T ABLE OF CONTENTS Section Page 1.0 W ARNINGS .................................................................................................................... .................... 1 2.0 SCOPE ................[...]
-
Page 3
LIST OF ILLUSTRA TIONS Figur e Page 1T ypical WL V500 Control Link and WL V2000 Video Link Configuration ............................................ 2 2T ransmitter-Receiver Placement at Same Site ................................................................................ 3 3 Multiple System Interference ......................................[...]
-
Page 4
(This page intentionally left blank.) iv Pelco Manual C914M (7/96)[...]
-
Page 5
Pelco Manual C914M (7/96) 1 This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 4 .O nly use replacement parts recom[...]
-
Page 6
2 Pelco Manual C914M (7/96) 2.0 SCOPE This manual covers the installation of the WL V2500 Series of outdoor wireless systems. 3.0 DESCRIPTION To make a WL V2500 system, a WL V500 control sys- tem is combined with a WL V200 video transmission system (refer to Figure 1). The wireless control systems of the WL V500 Series provide wireless remote contr[...]
-
Page 7
Pelco Manual C914M (7/96) 3 Figure 2. T ransmitter-Receiver Placement at Same Site 4.0 ANTENNA LOCA TION To provide the best reception, proper placement of the transmit and receive antennas is important. Reception will be best when: • The antennas are a minimum of 8-10 feet above the floor (indoors) or ground (outdoors). • The transmit and rece[...]
-
Page 8
4 Pelco Manual C914M (7/96) 5.0 INST ALLA TION NOTE: Proper placement of the transmit and receive antennas is important for best reception. Read Section 4.0, “Antenna Lo- cation,” before installing the equipment. Install the WL V500 receiver and WL V2000 transmit- ter at the remote site where your camera will be. Install the WL V500 transmitter[...]
-
Page 9
Pelco Manual C914M (7/96) 5 5.2 WIRING NOTE: In the following steps w hen you as- semble coaxial cable, install a BNC connector on only one end. Run the bare end of the cable through the cable entry gland on the enclosure so that the end with the BNC connector is inside the enclosure. Then add a BNC connector to the other end of the cable. Refer to[...]
-
Page 10
6 Pelco Manual C914M (7/96) 5.4 ANTENNA ALIGNMENT NOTE: This section applies only to the WL V2000 wireless receiver . 1. Connect a high impedance voltmeter to the RSSI (Received Signal Strength Indication) test points on the bottom of the enclosure: a. Set the voltmeter on a low-volt DC scale (3 or 10 volts). b. Connect the negative lead from the v[...]
-
Page 11
Pelco Manual C914M (7/96) 7 4. Check the power supply voltages for the wireless transmitter and receiver . If the voltage at the trans- mitter or receiver is less than 1 1 VDC, replace the unit’ s power supply . 5.5.2 Poor Picture 1. Refer to Section 4.0, “Antenna Location,” and verify that the transmit and receive antennas are positioned pro[...]
-
Page 12
8 Pelco Manual C914M (7/96) 6.0 EXPLODED ASSEMBL Y DIAGRAM (OUTDOOR MODELS ONL Y) Figure 6. Outdoor Enclosure Exploded Assembly Diagram[...]
-
Page 13
Pelco Manual C914M (7/96) 9 6.1 MECHANICAL P ARTS LIST Item Quantity Description Part Number 11 9-Pin Connector CON03-06-1091 22 Gland EH400010003 32 Gland Nut EH400010004 41 Gland CX950010000 51 Gland Nut CX950010001 62 Fuse Holder FUS342012L 71 Power Supply Assembly PCB9000281ASSY 81 3-Position T erminal Block TRB3-140Y 91 Tr ansformer T RF21162.[...]
-
Page 14
10 Pelco Manual C914M (7/96) 7.0 INTERCEPT ® DOME MODIFICA TION To use the WL V500 wireless control system with In- tercept ® dome drives DD08CXX, DD08EXX, DD14CXX, or DD14EXX (domes with 360 degree ro- tation), the following steps must be performed: NOTE : Refer to Figure 7, which gives a gen- eral layout of the dome drive and indicates the item[...]
-
Page 15
Pelco Manual C914M (7/96) 11 Figure 8. V ideo Board Component Locations Figure 9. Block Diagram[...]
-
Page 16
12 Pelco Manual C914M (7/96) Figure 10. Coaxitron ® Receiver Backplane PCB - Wire Lead Additions and Wiring Diagram[...]
-
Page 17
Pelco Manual C914M (7/96) 13 8.0 WIRING DIAGRAM NOTE: Output voltage is 15 VDC, not 10.5 Figure 1 1. Outdoor Enclosure Wiring Diagram 9.0 MAINTENANCE In cold, wet areas periodically visit the transmitter and receiver sites to prevent the buildup of snow and ice on the enclosures. A buildup of ice and snow will severely attenuate the microwave signa[...]
-
Page 18
14 Pelco Manual C914M (7/96) Impedance: 75 ohms Connectors: BNC RF (WL V500) T ransmitter Radiated Power: FCC Part 15 (15.249) T ransmit Antenna: Attached, circular -polarized, patch antenna Receive Antenna: Removable, 1 1 dBi, circular- polarized, patch antenna Receiver Connector: TNC Receiver Input Impedance: 50 ohms Frequency Range: 2400 to 2483[...]
-
Page 19
Pelco Manual C914M (7/96) 15 11.0 W ARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1996, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective[...]
-
Page 20
Pelco 3500 Pelco Way, Clovis, CA 93612-5699 (559) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (559) 292-3827 International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.) C914M[...]