Huffy UXT3030AA manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Huffy UXT3030AA, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Huffy UXT3030AA one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Huffy UXT3030AA. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Huffy UXT3030AA should contain:
- informations concerning technical data of Huffy UXT3030AA
- name of the manufacturer and a year of construction of the Huffy UXT3030AA item
- rules of operation, control and maintenance of the Huffy UXT3030AA item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Huffy UXT3030AA alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Huffy UXT3030AA, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Huffy service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Huffy UXT3030AA.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Huffy UXT3030AA item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    1 03/04 P/N 21463607 © COPYRIGHT 2000 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.huffysports.com Por table System Owners Manual Customer Service Center • N53 W24700 South Co[...]

  • Page 2

    2 P/N 21463607 03/04 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard bracket s, and triangle plates. Carefully rock them in a circular motion to ream out any excess p aint from [...]

  • Page 3

    03/04 P/N 21463607 3 W ARNING F AILURE T O FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, support braces or net. • During play , especially whe[...]

  • Page 4

    4 P/N 21463607 03/04 SAFETY I NSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions car[...]

  • Page 5

    03/04 P/N 21463607 5 For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside. NOTICE T O ASSEMBLERS AL L Huffy S port s Ba[...]

  • Page 6

    6 P/N 21463607 03/04 Get to know the basic parts of your basketball system..... FRONT P ANEL BACKBOARD FRONT RIM BASE POLE[...]

  • Page 7

    03/04 P/N 21463607 7 P ARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 200503 Cover, Black 2 1 806620 Base Assembly 3 1 804833 Exacta Height Assembly 4 1 908006 Top Pole Section 5 1 908107 Middle Pole Section 6 1 908005 Bottom Pole Section 7 2 206934 Large Eyebolt, 3/8” 8 2 203063 Nylon Insert Lock Nut, 3/8-16 9 1 206634 [...]

  • Page 8

    8 P/N 21463607 03/04 HARDW ARE IDENTIFIER (BOL TS & SCREWS) * You may have extra parts with this model. Item #7 (2) Item #40 (1) Item #50 (2) Item #23 (1) Item #29 (6) Item #16 (2) Item #12 (1) Item #48 (4)[...]

  • Page 9

    03/04 P/N 21463607 9 HARDW ARE IDENTIFIER (STEEL SP ACERS) HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS CAPS & CLIPS) Item #28 (2) Item #21 (2) Item #13 (2) Item #20 (2) Item #26 (4) Item #30 (4) Item #36 (2) Item #1 1(4) Item #42 (12)* Item #18 (4) Item #14 (1 1) Item #10 (1) Item #8 (2) Item #31 (7) Item #[...]

  • Page 10

    10 P/N 21463607 03/04 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION A : ASSEMBLE THE BASE And/Or: This is what your system will look like when you’ve finished this section: Item #50 Item #23 Item #16 Item #12 (1) Item #19 Item #21 Item #13 Item #20 Item #18 Item #14 Item #10 Item #8 Item #19 Item #47 1/2[...]

  • Page 11

    03/04 P/N 21463607 11 1A. Check the following pre-assembled base areas for tightness: Eye bolt s P/N 203452, W asher P/N 203218 , Nut P/N 203100, Carriage Bolt s P/N 203223 . Eye bolt s P/N 203452 W asher P/N 203218 Nut P/N 203100 Front Cover P/N 206002 Pole Bracket P/N 201581 Carriage Bolt s P/N 203223 Hex Flange Nut P/N 203100 W asher P/N 203218 [...]

  • Page 12

    12 P/N 21463607 03/04 Check the following pre-assembled handle areas for tightness: Screw P/N 2048032, Nut P/N 203100, Carriage Bolt s P/N 203103 . Carriage Bolt P/N 203103 Nut P/N 203100 Nut P/N 203100 Handle, Right P/N 204856 Handle, Lef t P/N 204855 Screw P/N 204803 Carriage Bolt P/N 203103 Height Adjustment Rod P/N 904833 Label,Height Indicator[...]

  • Page 13

    03/04 P/N 21463607 13 2. Mark pole sections with tape (not supplied) as shown. 6 5 4 3. WOOD SCRAP (NOT SUPPLIED) 5 4 While maintaining alignment, bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no longer moves toward the taped reference mark on the middle pole. Upright assembly . T ape (Not Suppli[...]

  • Page 14

    14 P/N 21463607 03/04 4. Bounce top (4) and middle (5) pole assembly onto bottom pole section (6) using a wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the taped reference mark on the bottom pole. 5. Install bolt (12) through bracket and bottom pole section (6) and secure with nut (10) as shown. Nut shoul[...]

  • Page 15

    03/04 P/N 21463607 15 Install rod (9) through bottom pole section (6) as shown. Inst all large eye bolts (7) onto rod (9) as shown. 7. Secure cover to rod (9) using washers (47) nuts (8) and nut covers (13) as shown. 6. 9 7 6 9 7 13 8 47[...]

  • Page 16

    16 P/N 21463607 03/04 8 . Install pole mount bracket (15) and reinforcement bracket (49) with carriage bolt s (16) as shown. T ighten flange nuts (14) completely . 4 15 14 14 49 16 16 9. Attach sp acers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), and nuts (18) as shown. 15 17 17 18 19 17 17 21 20 20 21 IMPORT A NT! : T ighten[...]

  • Page 17

    03/04 P/N 21463607 17 Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. 10 . 15 14 24 22 22 25 23 FIG . A 25 24 Loop end of pin lanyard (25) over carriage bolt (23) as it p asses through the pole mount bracket (15) during this assembly . IMPORT [...]

  • Page 18

    18 P/N 21463607 03/04 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (24). 24 11 .[...]

  • Page 19

    03/04 P/N 21463607 19 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION B: A TT ACH THE BACKBOARD Phillip s- Head Screwdriver This is what your system will look like when you’ve finished this section: Item #40 Item #50 Item #29 Item #19 Item #28 Item #26 Item #30 Item #36 Item #61 Item #42 Item #18 Item #31 [...]

  • Page 20

    20 P/N 21463607 03/04 Assemble backboard brackets (27) using sp acers (28), bolts (19), and nuts (18) as shown. 1. 28 28 19 19 18 18 27[...]

  • Page 21

    03/04 P/N 21463607 21 2. 3. Install cover (1) over spring return mechanism as shown. 29 33 26 26 27 31 Refer T o Instructions Included With Rim Hardware For Rim Assembly . 48 11 47 32 34 1 39 Attach lower elevator tubes (32) and counter balance spring (33) to backboard support brackets (27) using sp acers (26), bolt (29), and nut (31) as shown. Rim[...]

  • Page 22

    22 P/N 21463607 03/04 4. Attach upper elevator tubes (35) to backboard support bracket s (27) using spacers (26 & 1 1)), bolt (29), and nut (31) as shown. 35 35 26 27 26 31 11 29 29 27 26 31 11 Peel protective film from surface of acrylic backboard prior to use. NOTE:[...]

  • Page 23

    03/04 P/N 21463607 23 5. Install net clip s. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. Push second “arm” back and into ram as shown. T wist “body” of cli[...]

  • Page 24

    24 P/N 21463607 03/04 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INST ALLA TION 6. 34 42 43[...]

  • Page 25

    03/04 P/N 21463607 25 31 31 40 38 32 4 37 37 29 30 32 30 29 32 29 35 30 31 31 35 30 37 36 36 7. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (38). Use caution; elevator assembly is heavy . 8. Install upper elevator tubes (35) to triangle plates (37) as shown. Inst all handle assembly to lowe[...]

  • Page 26

    26 P/N 21463607 03/04 35 33 31 29 35 9. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (33) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). 10. Roll completed assembly to desired position. Fill tank with water (approx. 34 gallons (129 Liters)) or sand (approx. [...]

  • Page 27

    03/04 P/N 21463607 27 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24). B. Move elevator up or down to desired height. C. Replace pin (24) full length to lock system at desired height. SECTION C: APPL Y HEIGHT AND MOVING LABEL & HEIGHT ADJUSTMENT 46 10 ft. (3.05 m) 24 A. B. [...]

  • Page 28

    28 P/N 21463607 03/04 Numéro sans frais du service clientèle (États-Unis) : 1-800-558-5234 ; Canada : 1-800-284-8339 ; Europe : 00 800 555 85234 (Suède : 009 555 85234), Pour l'Australie : 1-800-333 061 - Site Internet : http://www.huffysports.com Gebührenfreie Kundendienstnummer für Anrufer in den USA: 1-800-558-5234 Für Anrufer in Kan[...]

  • Page 29

    03/04 P/N 21463607 29 A V ANT DE COMMENCER! VORBEREITENDE MASSNAHMEN ¡ANTES DE COMENZAR! Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien ajustés (serrés). À titre d'essai, insérez les gros boulons dans les gros trous des tubes du système élévateur, des suppo[...]

  • Page 30

    30 P/N 21463607 03/04 SUIVEZ CES AVERTISSEMENTS SOUS PEINE DE PROVOQUER DES BLESSURES GRAVES ET/OU DES DEGATS MATERIELS. Le propriétaire du système doit s’assurer que tous les joueurs connaissent et suivent ces consignes d’utilisation sûre du système. • NE VOUS SUSPENDEZ PAS sur le cerceau ou sur toute autre partie du système, y compris [...]

  • Page 31

    03/04 P/N 21463607 31 SICHERHEITSHINWEISE EIN MISSACHTEN DIESER SICHERHEITSHINWEISE KANN ZU SCHWEREN VERLETZUNGEN UND/ODER SACHSCHÄDEN FÜHREN UND MACHT DIE GARANTIE UNWIRKSAM.. Der Eigentümer muss sicherstellen, dass alle Spieler diese Regeln für einen sicheren Betrieb des Systems kennen und befolgen. Aus Sicherheitsgründen darf dieses System [...]

  • Page 32

    32 P/N 21463607 03/04 IMPORTANT! Videz entièrement les boîtes. Veillez à vérifier l'intérieur des sections de poteau. La quincaillerie et des pièces supplémentaires sont emballées à l'intérieur. ¡IMPORTANTE! Saque todo el contenido de las cajas. Asegúrese de revisar el interior de las secciones del poste. Ahí se han empacado [...]

  • Page 33

    03/04 P/N 21463607 33 AVERTISSEMENT : SI VOTRE SYSTÈME EST ÉQUIPÉ D'UN PANNEAU EN ACRYLIQUE, EXAMINEZ-LE BIEN POUR VOUS ASSURER QU'IL N'A PAS ÉTÉ ENDOMMAGÉ EN COURS DE TRANSPORT. S'IL EST FISSURÉ, IL RISQUE DE SE CASSER SUBITEMENT. SI LE PANNEAU EST ENDOMMAGÉ D'UNE QUELCONQUE MANIÈRE AVANT OU APRÈS L'ASSEMBLA[...]

  • Page 34

    34 P/N 21463607 03/04 IDENTIFICA TION DES PIÈCES (BOULONS & VIS) BEFESTIGUNGSTEILESCHLÜSSEL (BOLZEN UND SCHRAUBEN) IDENTIFICADOR DE HERRAJE (PERNOS Y TORNILLOS) * You may have extra parts with this model. #7 (2) #40 (1) #50 (2) #23 (1) #29 (6) #16 (2) #12 (1) #48 (4)[...]

  • Page 35

    03/04 P/N 21463607 35 IDENTIFICA TION DES PIÈCES (ENTRETOISES EN ACIER) BEFESTIGUNGSTEILESCHLÜSSEL (ABST ANDSSTÜCKE AUS ST AHL) IDENTIFICADOR DEL HERRAJE (ESP ACIADORES DE ACERO) IDENTIFICA TION DES PIÈCES (ÉCROUS & RONDELLES) BEFESTIGUNGSTEILESCHLÜSSEL (MUTTERN UND UNTERLEGSCHEIBEN) IDENTIFICADOR DE HERRAJE (TUERCAS Y ARANDELAS) IDENTIFI[...]

  • Page 36

    36 P/N 21463607 03/04 OUTILS REQUIS POUR CETTE SECTION FÜR DIESEN BAUABSCHNITT BENÖTIGTES WERKZEUG HERRAMIENTAS REQUERIDAS PARA ESTA SECCIÓN VISSERIE UTILISÉE DANS CETTE SECTION (pas à l'échelle) IN DIESEM BAUABSCHNITT BENUTZTE BEFESTIGUNGSTEILE (die Abbildungen entsprechen nicht der tatsächlichen Größe) HERRAJE USADO EN ESTA SECCIÓN[...]

  • Page 37

    03/04 P/N 21463607 37 Vérifiez le serrage des zones pré-assemblées suivantes du socle : Boulons à œil (no de réf. 203452), rondelle (no de réf. 203218), écrou (no de réf. 203100), boulons ordinaires (no de réf. 203223). Überprüfen Sie die folgenden vormontierten Sockelbauteile auf ihren festen Sitz: Einschraubösen Nr .203452, Unterlegs[...]

  • Page 38

    38 P/N 21463607 03/04 Boulon ordinaire no de réf. 203103 Schlossschraube Nr . 203103 Perno cabeza de carro N/P 203103 Écrou no de réf. 203100 Mutter Nr . 203100 T uerca N/P 203100 Écrou no de réf. 203100 Mutter Nr . 203100 T uerca N/P 203100 Poignée, droite no de réf. 204856 Griff recht s, Nr . 204856 Asa, derecha N/P 204856 Poignée, gauche[...]

  • Page 39

    03/04 P/N 21463607 39 2. 6 5 4 3. 5 4 Tout en maintenant l'alignement, entrechoquez les sections de poteau supérieure (4) et centrale (5) en utilisant une chute de bois, comme illustré, jusqu'à ce qu'elles ne bougent plus vers le repère de référence (ruban adhésif). Redressez l'ensemble. Unter Wahrung der korrekten Ausric[...]

  • Page 40

    40 P/N 21463607 03/04 4. Entrechoquez l'ensemble sections supérieure (4) et centrale (5) avec la section inférieure (6) à l'aide d'une chute de bois, comme illustré. Entrechoquez-les jusqu'à ce que l'ensemble sections supérieure et centrale ne bougent plus vers le repère de référence (ruban adhésif) sur la section[...]

  • Page 41

    03/04 P/N 21463607 41 6. 9 7 6 9 7 Enfilez la tige (9) dans la section de poteau inférieure (6), comme illustré. Installez les boulons à œil (7) sur la tige (9), comme illustré. Die Stange (9) wie gezeigt durch das untere Stangenteil (6) anbringen. Die großen Einschraubösen (7) wie gezeigt an der Stange (9) anbringen. Instale la varilla (9) [...]

  • Page 42

    42 P/N 21463607 03/04 8 . 4 15 14 14 49 16 16 9. 15 17 17 18 19 17 17 21 20 20 21 Attachez les entretoises (20, 21) au support de poteau (15) avec les boulons (19), les rondelles (17) et les écrous (18), comme illustré. Die Abstandsstücke (20, 21) wie gezeigt mit Schrauben (19), Unterlegscheiben (17) und Muttern (18) an der Stangenmontagehalteru[...]

  • Page 43

    03/04 P/N 21463607 43 10 . 15 14 24 22 22 25 23 24 11 . DURANT LE MONTAGE, ENFILEZ LE BOULON ORDINAIRE (23) DANS L'EXTRÉMITÉ DU CORDON (25) AVANT DE LE FAIRE PASSER DANS LE SUPPORT DE POTEAU (15). WÄHREND DIESES MONTAGESCHRITTS DAS ENDE DER STIFTLEINE (25) ÜBER DIE SCHLOSSSCHRAUBE (23) SCHLINGEN, WENN DIESE DURCH DIE STANGENMONTAGEHALTERUN[...]

  • Page 44

    44 P/N 21463607 03/04 Item #40 Item #50 Item #29 Item #19 Item #28 Item #26 Item #30 Item #36 Item #61 Item #42 Item #18 Item #31 Item #55 Item #48 SECTION B : A TT ACHEZ LE P ANNEAU BAUABSCHNITT B: ANBRINGEN DER KORBW AN D SECCIÓN B: CONECTE EL RESP ALDO (2) clés 1/2", (2) clés 9/16" ET (2) clés 3/4" (2) 1/2", (2) 9/16"[...]

  • Page 45

    03/04 P/N 21463607 45 1. 28 28 19 19 18 18 27 Assemblez les supports de panneau (27) à l'aide des entretoises (28), des boulons (19) et des écrous (18), comme illustré. Die Korbwandklammern (27) wie gezeigt mit Abstandsstücken (28), Schrauben (19) und Muttern (18) zusammenbauen. Monte los soportes del respaldo (27) usando espaciadores (28)[...]

  • Page 46

    46 P/N 21463607 03/04 2. 3. Installez le couvercle (1) sur le mécanisme de retour du ressort, comme illustré. Die Abdeckung (1) wie über dem Federrückholmechanismus anbringen. Instale la cubierta (1) sobre el mecanismo de retorno de resorte como se muestra. 29 33 26 26 27 31 48 11 47 32 34 1 39 Attachez les tubes inférieurs de l'élévate[...]

  • Page 47

    03/04 P/N 21463607 47 4. 35 35 26 27 26 31 11 29 29 27 26 31 11 REMARQUE: HINWEIS: NOT A : Décollez le film de protection de la surface du panneau en acrylique avant usage. Vor Gebrauch die Schutzfolie von der Oberfläche der Akryl- Korbwand abziehen. Desprenda la película protectora de la superficie del respaldo de acrílico antes de usarlo. Att[...]

  • Page 48

    48 P/N 21463607 03/04 5. Installez les pinces. Netzhalteklammern (Clips) anbringen. Instale los sujetadores. CLIP “ARM” CLIP “BODY” Insérez un " bras " de la pince dans l'éperon, comme illustré. Tournez légèrement le corps de la pince de sorte que le second bras glisse par- dessus le premier, comme illustré. Poussez dan[...]

  • Page 49

    03/04 P/N 21463607 49 31 31 40 38 32 4 37 37 29 30 32 30 29 32 29 35 30 31 31 35 30 37 36 36 7. Appuyez le poteau sur le banc de sciage. Attachez le panneau à la section de poteau supérieure (4), comme illustré. Installez le capuchon du poteau (38). Soyez prudent, car le système élévateur est lourd. Die Stange auf einen Sägebock legen. Die K[...]

  • Page 50

    50 P/N 21463607 03/04 35 33 31 29 9. Enfilez le boulon (29) dans le tube supérieur gauche du système élévateur (35), puis tendez le ressort (33) sur le boulon (29). Enfilez le boulon (29) dans le tube supérieur droit du système élévateur (35), puis fixez avec l'écrou (31). Die Schraube (29) durch das linke obere Verlängerungsrohr (35[...]

  • Page 51

    03/04 P/N 21463607 51 1. Collez l'étiquette d'échelle de hauteur et de déplacement (46) sur l'avant du poteau, comme illustré. Höheneinstell- und Transportaufkleber (46) wie gezeigt an der Vorderseite der Stange anbringen. Aplique la etiqueta de ajuste de la altura y de movimiento (46) en la parte frontal del poste, como se mues[...]