English dropdown-ico

Extron electronic XTP T UWP 302 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Extron electronic XTP T UWP 302, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Extron electronic XTP T UWP 302 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Extron electronic XTP T UWP 302. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Extron electronic XTP T UWP 302 should contain:
- informations concerning technical data of Extron electronic XTP T UWP 302
- name of the manufacturer and a year of construction of the Extron electronic XTP T UWP 302 item
- rules of operation, control and maintenance of the Extron electronic XTP T UWP 302 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Extron electronic XTP T UWP 302 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Extron electronic XTP T UWP 302, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Extron electronic service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Extron electronic XTP T UWP 302.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Extron electronic XTP T UWP 302 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    User Guide XTP T UWP 302 XTP Extender T wo Input XTP T ransmitter – W allplate 68-2541-01 Rev . A 01 14[...]

  • Page 2

    Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may pr esent a risk of electric shock. A TTENTION: This symbol, , when used on the product, is intended to alert the user of important operating and [...]

  • Page 3

    FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interfer ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radi[...]

  • Page 4

    Conventions Used in this Guide Notifications The following notifications are used in this guide: W ARNING: A warning indicates a situation that has the potential to result in death or severe injury . CAUTION: A caution indicates a situation that may result in minor injury . A TTENTION: Attention indicates a situation that may damage or destroy the [...]

  • Page 5

    Contents SIS Configuration and Control ..................... 17 Host Device Connection ................................... 17 SIS Programming Guide ................................... 17 Host-to-Device and Device-to-Host Communication ........................................... 17 Device-Initiated Message .............................. 17 Error Re[...]

  • Page 6

    XTP T UWP 302 • Contents vi[...]

  • Page 7

    XTP T UWP 302 • Introduction 1 Intr oduction This section contains general information about this guide and the Extron XTP T UWP 302 wallplate transmitter . T opics in this section include: • About this Guide • About the XTP T UWP 302 • Key Features About this Guide This guide contains installation, operation, and control pr ocedures, and r[...]

  • Page 8

    XTP T UWP 302 • Introduction 2 Key Featur es W all mountable — Mounts in a standard three-gang junction box or the pr ovided mud ring. Inputs — Include one HDMI input and one VGA input. Computer -video to 1920x1200 support, including HDTV 1080p/60 Deep Color and 2K signals — Supports digital signal transmission up to 330 feet over a single [...]

  • Page 9

    XTP T UWP 302 • Installation and Operation 3 Installation and Operation This section contains information for mounting, connecting, and wiring the XTP T UWP 302. T opics in this section include: • Installation Overview • Installing the Mud Ring or Junction Box • Rear and Side Panel Connectors • Mounting the XTP T UWP 302 • Front Panel C[...]

  • Page 10

    XTP T UWP 302 • Installation and Operation 4 Installing the Mud Ring or Junction Box Cutting an Opening in the Mounting Surface 1. Using an appropriate template or the mounting enclosur e as a guide, mark the area of the wall with a soft pencil that will be cut (for the provided mud ring, see Mounting T emplate on page 39). NOTE: Check with the m[...]

  • Page 11

    XTP T UWP 302 • Installation and Operation 5 3. Insert the mounting bracket into the opening in the wall. 4. Rotate each backing clip so that the tab is behind the installation surface to hold the bracket snuggly in place when the screw is tightened. Detail A 0.75" #6-32 Scre w Backing Clip Backing Clip Mountint Surface Mounting Surface Deta[...]

  • Page 12

    XTP T UWP 302 • Installation and Operation 6 Installing a UL-certified Junction Box 1. Insert the junction box into the hole in the wall. 2. Secure it to the stud using two scr ews or nails, as appropriate. The front edge of the junction box must be flush with the front surface of the wall. 3. Secure cables with clamps or ties to pr ovide strain [...]

  • Page 13

    XTP T UWP 302 • Installation and Operation 7 b RS-232 Over XTP port — T o pass bidirectional serial or other control signals between XTP-compatible devices, connect a control device to the 5-pole captive scr ew connector . The port includes only the 3 poles labeled “RS-232.” IR Over XTP port — T o transmit and receive IR signals (up to 40[...]

  • Page 14

    XTP T UWP 302 • Installation and Operation 8 Mounting the XTP T UWP 302 Bac king Clip Extron XTP T UWP 302 AUDIO IN PWR H DCP HDMI VGA HDMI IN VGA IN Figure 7. Installing the XTP T UWP 302 in the Provided Mud Ring Wall Stud Extron XTP T UWP 302 AUDIO IN PWR HDCP HDMI VGA HDMI IN VGA IN Figure 8. Installing the XTP T UWP 302 in a Junction Box 1. A[...]

  • Page 15

    XTP T UWP 302 • Installation and Operation 9 Fr ont Panel Connections AU DI O IN PW RH DCP HDMI VG A HDMI IN VG A IN ab c Figure 9. Front Panel Connectors a HDMI connectors — Connect a digital video source device to the HDMI connector . It can accept HDMI, DVI, or dual mode DisplayPort video sources. b Audio connector — Connect an analog audi[...]

  • Page 16

    XTP T UWP 302 • Installation and Operation 10 Making Connections HDMI Connection Use an Extron LockIt Lacing Bracket to secur e an HDMI cable to each connector as follows: 3 3 1 2 4 5 Figure 11. Installing the LockIt Lacing Bracket 1. Plug the HDMI cable into the panel connection. 2. Loosen the HDMI connection mounting screw fr om the panel enoug[...]

  • Page 17

    XTP T UWP 302 • Installation and Operation 11 TP Cable T ermination and Recommendations Use the following pin configurations for twisted pair cables. 12345678 RJ-45 Connector Inser t T wisted P air Wires Pins: Pin 1 2 3 4 5 6 7 8 Wire color White-green Green White-orange Blue White-blue Orange White-brown Brown Wire color T568A T568B White-orange[...]

  • Page 18

    XTP T UWP 302 • Installation and Operation 12 RS-232 and IR Over XTP Communication The RS-232 and IR Over XTP connector is for pass-through transmission of serial signals, such as projector contr ol signals, and Infrared data (see figure 13 for an example of how to wire the connector). Tx/Rx Pins Rx Tx RS-232 Rx Tx Tx Rx Rx Tx Custom IR Device RS[...]

  • Page 19

    XTP T UWP 302 • Installation and Operation 13 Power Connection Apply power to the transmitter locally with the provided power supply or r emotely with a power injector or an XTP matrix switcher . A TTENTION: XTP remote power is intended for indoor use only . No part of the network that uses XTP remote power should be r outed outdoors. Local power[...]

  • Page 20

    XTP T UWP 302 • Installation and Operation 14 Remote power The XTP T UWP 302 can be powered r emotely through an XTP Power Injector or through an XTP matrix switcher . A TTENTION: XTP remote power is intended for indoor use only . No part of the network that uses XTP remote power should be r outed outdoors. Power injector T o power the XTP T UWP [...]

  • Page 21

    XTP T UWP 302 • Installation and Operation 15 Operation After all transmitters, all receivers, and their connected devices ar e powered up, the system is fully operational. If any problems ar e encountered, verify that the cables are r outed and connected properly . If problems persist, call the Extron S3 Sales & T echnical Support Hotline. S[...]

  • Page 22

    XTP T UWP 302 • Installation and Operation 16 Reset Modes Use the recessed Reset button on the r ear panel of the transmitter to return the device to default settings or to restor e factory-shipped firmware. T o access the Reset button, the XTP T UWP 302 may need to be removed fr om the mud ring or junction box. Reset Mode Summary Mode Activation[...]

  • Page 23

    XTP T UWP 302 • SIS Configuration and Control 17 SIS Configuration and Contr ol The XTP T UWP 302 can be configured and contr olled using Extron Simple Instruction Set (SIS) commands or the XTP System Configuration Software (see XTP System Configuration Software on page 22). This section contains basic SIS communication details and SIS commands a[...]

  • Page 24

    XTP T UWP 302 • SIS Configuration and Control 18 Error Responses When the XTP T UWP 302 receives an SIS command and determines that it is valid, it performs the command and sends the corresponding r esponse to the host device. If the command is determined invalid or contains invalid parameters, the switcher returns an error response to the host. [...]

  • Page 25

    XTP T UWP 302 • SIS Configuration and Control 19 Command and Response T ables for SIS Commands Command ASCII Command (Host to Device) Response (Device to Host) Additional Description Input Commands Input selection Select input X! ! In X!] Select input X! . View the selected input ! In X! ] V iew the selected input. Auto switch mode Disable auto s[...]

  • Page 26

    XTP T UWP 302 • SIS Configuration and Control 20 Command ASCII Command (Host to Device) Response (Device to Host) Additional Description Black signal for audio only NOTE: The switcher uses a black signal to simulate a 720p or 1080p, 50 Hz or 60 Hz signal so audio can be passed without video. Enable black signal E B1AFMT } AfmtB X( ] Enable a blac[...]

  • Page 27

    XTP T UWP 302 • SIS Configuration and Control 21 Command ASCII Command (Host to Device) Response (Device to Host) Additional Description EDID Commands NOTE: For EDID management, use the XTP System Configuration Software (see EDID Minder on page 33). Advanced Configuration Commands HDCP authorized device (HDMI input only) HDCP authorized device On[...]

  • Page 28

    XTP T UWP 302 • XTP System Configuration Software 22 XTP System Configuration Softwar e This section contains installation and configuration procedur es for the XTP System Configuration Software for configuring and contr olling the XTP T UWP 302. T opics in this section include: • Installing the XTP System Configuration Software • Using the X[...]

  • Page 29

    XTP T UWP 302 • XTP System Configuration Software 23 Using the XTP System Configuration Softwar e The XTP T UWP 302 can be controlled dir ectly from the side panel config port or remotely from an XTP matrix switcher . Connections When opening the XTP System Configuration Software, the Connections scr een opens first. This screen is used to establ[...]

  • Page 30

    XTP T UWP 302 • XTP System Configuration Software 24 T op Menu The top menu bar contains three menus for configuring softwar e settings. File menu The File menu contains options for disconnecting and exiting the program. T o access the menu, click the File menu. Figure 20. File Menu Disconnect This option disconnects the XTP System Configuration [...]

  • Page 31

    XTP T UWP 302 • XTP System Configuration Software 25 Update Firmware This option uploads firmware fr om the host device to the connected device. NOTE: If necessary , download new firmware fr om the Extron website (see Downloading Firmware on page 37). 1. From the Tools menu, select Update Firmware . A dialog box opens to ask permission to disconn[...]

  • Page 32

    XTP T UWP 302 • XTP System Configuration Software 26 Help menu The Help menu contains XTP System Configuration Software information, the help file, and a link to the Extron website. Figure 24. Help Menu About the Software This option provides basic information about the XTP System Configuration Softwar e, including version number and copyright in[...]

  • Page 33

    XTP T UWP 302 • XTP System Configuration Software 27 Device Settings The Device Settings screen allows a user to view and edit various device settings for the device directly connected to the host device. Click the Device Settings icon on the Global Navigation bar to open the Device Settings screen. Figure 26. T ransmitter Device Settings Screen [...]

  • Page 34

    XTP T UWP 302 • XTP System Configuration Software 28 Input/Output tab Click the Input/Output tab to open the Input/Output screen. It contains input information and options to apply automatic settings to individual inputs. Figure 27. Input/Output T ab Input name — Displays the input name. Signal type — Displays the signal type of each input. I[...]

  • Page 35

    XTP T UWP 302 • XTP System Configuration Software 29 Analog Video tab Click the Analog Video tab to open the Analog Video screen. It contains signal sampling, image shifting, and saving and recalling input pr eset options. Figure 28. Analog Video T ab Signal Sampling panel Signal sampling optimizes the input signal to the transmitter for the curr[...]

  • Page 36

    XTP T UWP 302 • XTP System Configuration Software 30 Audio tab Click the Audio tab to open the Audio screen. It contains settings for input format and analog audio gain. Figure 29. Audio T ab Input format section Input format — From the Audio Format dr op-down list, select the format for input 2. It can be Auto , HDMI , or Analog . Analog audio[...]

  • Page 37

    XTP T UWP 302 • XTP System Configuration Software 31 General tab Click the General tab to open the general screen. It contains settings for executive mode, auto switch mode, and factory reset. Figure 30. General T ab Executive mode section Unlock the front panel — Click the Unlock Front Panel radio button (default) to disable executive mode. Lo[...]

  • Page 38

    XTP T UWP 302 • XTP System Configuration Software 32 Device Information panel The Device Information panel displays device information and settings. General Information section Model — Displays the device model. Firmware version — Displays the full firmwar e version. Signal Information section Selected input — Displays the input number of t[...]

  • Page 39

    XTP T UWP 302 • XTP System Configuration Software 33 EDID Minder Use the EDID Minder screen to assign unique EDID to the input or match curr ent output resolutions to the input. Click the EDID Minder icon on the global navigation bar . The EDID Minder screen opens. The EDID Minder screen displays a table of EDID options and connected output devic[...]

  • Page 40

    XTP T UWP 302 • XTP System Configuration Software 34 Import EDID 1. On the EDID Minder screen, click the Add EDID to Library button. 2. Select the desired EDID file and click Open . The EDID appears in the A vailable EDID pane. 3. Assign the EDID from the A vailable EDID pane to import the EDID setting to the device. Save output EDID 1. On the ED[...]

  • Page 41

    XTP T UWP 302 • Reference Information 35 Refer ence Information This section contains mounting information and instructions for updating firmware. T opics in this section include: • Updating Firmware with Firmwar e Loader • Mounting T emplate Updating Firmwar e with Firmware Loader T o upload and update firmware for the XTP T UWP 302, downloa[...]

  • Page 42

    XTP T UWP 302 • Reference Information 36 Figure 34. Navigating to Firmwar e Loader 3. Navigate to Firmware Loader . 4. Click the Download link on the right that corresponds with the pr ogram. 5. Submit any requir ed information to start the download. Note where the file is saved. Installing Firmware Loader 1. Once Firmware Loader has been downloa[...]

  • Page 43

    XTP T UWP 302 • Reference Information 37 Downloading Firmware Figure 35. Downloading Firmwar e from the Extron W ebsite 1. On the Extron website , click the Download tab. 2. On the left sidebar , click the Firmware link. 3. Navigate to the XTP T UWP 302. 4. Ensure the available firmwar e version is a later version than the current one on the devi[...]

  • Page 44

    XTP T UWP 302 • Reference Information 38 Installing Firmware with Firmwar e Loader Use the Firmware Loader utility to upload firmwar e to the transmitter when connected directly to the device. 1. Connect the host device to the side panel USB port. 2. Open Firmware Loader and establish a connection between the computer and the device. The Add Devi[...]

  • Page 45

    XTP T UWP 302 • Reference Information 39 Mounting T emplate Figure 37 is a example of a mounting template for pr eparing mounting surfaces. It is not to full size. T emplate for the 3-gang mounting bracket 6.41" (16.3 cm) 4.50" (11.4 cm) TEMPLA TE IS NOT FULL SIZE. Recommended cut-out area f or the installation surface . T op P anel SUR[...]

  • Page 46

    Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron Asia +65.6383.4400 +65.6383.4664 F AX Extron Japan +81.3.3511.7655 +81.3.3511.7656 F[...]