Deutsch dropdown-ico

Extron electronic XTP T UWP 302 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Extron electronic XTP T UWP 302 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Extron electronic XTP T UWP 302, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Extron electronic XTP T UWP 302 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Extron electronic XTP T UWP 302. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Extron electronic XTP T UWP 302 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Extron electronic XTP T UWP 302
- Den Namen des Produzenten und das Produktionsjahr des Geräts Extron electronic XTP T UWP 302
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Extron electronic XTP T UWP 302
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Extron electronic XTP T UWP 302 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Extron electronic XTP T UWP 302 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Extron electronic finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Extron electronic XTP T UWP 302 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Extron electronic XTP T UWP 302, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Extron electronic XTP T UWP 302 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    User Guide XTP T UWP 302 XTP Extender T wo Input XTP T ransmitter – W allplate 68-2541-01 Rev . A 01 14[...]

  • Seite 2

    Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may pr esent a risk of electric shock. A TTENTION: This symbol, , when used on the product, is intended to alert the user of important operating and [...]

  • Seite 3

    FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interfer ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radi[...]

  • Seite 4

    Conventions Used in this Guide Notifications The following notifications are used in this guide: W ARNING: A warning indicates a situation that has the potential to result in death or severe injury . CAUTION: A caution indicates a situation that may result in minor injury . A TTENTION: Attention indicates a situation that may damage or destroy the [...]

  • Seite 5

    Contents SIS Configuration and Control ..................... 17 Host Device Connection ................................... 17 SIS Programming Guide ................................... 17 Host-to-Device and Device-to-Host Communication ........................................... 17 Device-Initiated Message .............................. 17 Error Re[...]

  • Seite 6

    XTP T UWP 302 • Contents vi[...]

  • Seite 7

    XTP T UWP 302 • Introduction 1 Intr oduction This section contains general information about this guide and the Extron XTP T UWP 302 wallplate transmitter . T opics in this section include: • About this Guide • About the XTP T UWP 302 • Key Features About this Guide This guide contains installation, operation, and control pr ocedures, and r[...]

  • Seite 8

    XTP T UWP 302 • Introduction 2 Key Featur es W all mountable — Mounts in a standard three-gang junction box or the pr ovided mud ring. Inputs — Include one HDMI input and one VGA input. Computer -video to 1920x1200 support, including HDTV 1080p/60 Deep Color and 2K signals — Supports digital signal transmission up to 330 feet over a single [...]

  • Seite 9

    XTP T UWP 302 • Installation and Operation 3 Installation and Operation This section contains information for mounting, connecting, and wiring the XTP T UWP 302. T opics in this section include: • Installation Overview • Installing the Mud Ring or Junction Box • Rear and Side Panel Connectors • Mounting the XTP T UWP 302 • Front Panel C[...]

  • Seite 10

    XTP T UWP 302 • Installation and Operation 4 Installing the Mud Ring or Junction Box Cutting an Opening in the Mounting Surface 1. Using an appropriate template or the mounting enclosur e as a guide, mark the area of the wall with a soft pencil that will be cut (for the provided mud ring, see Mounting T emplate on page 39). NOTE: Check with the m[...]

  • Seite 11

    XTP T UWP 302 • Installation and Operation 5 3. Insert the mounting bracket into the opening in the wall. 4. Rotate each backing clip so that the tab is behind the installation surface to hold the bracket snuggly in place when the screw is tightened. Detail A 0.75" #6-32 Scre w Backing Clip Backing Clip Mountint Surface Mounting Surface Deta[...]

  • Seite 12

    XTP T UWP 302 • Installation and Operation 6 Installing a UL-certified Junction Box 1. Insert the junction box into the hole in the wall. 2. Secure it to the stud using two scr ews or nails, as appropriate. The front edge of the junction box must be flush with the front surface of the wall. 3. Secure cables with clamps or ties to pr ovide strain [...]

  • Seite 13

    XTP T UWP 302 • Installation and Operation 7 b RS-232 Over XTP port — T o pass bidirectional serial or other control signals between XTP-compatible devices, connect a control device to the 5-pole captive scr ew connector . The port includes only the 3 poles labeled “RS-232.” IR Over XTP port — T o transmit and receive IR signals (up to 40[...]

  • Seite 14

    XTP T UWP 302 • Installation and Operation 8 Mounting the XTP T UWP 302 Bac king Clip Extron XTP T UWP 302 AUDIO IN PWR H DCP HDMI VGA HDMI IN VGA IN Figure 7. Installing the XTP T UWP 302 in the Provided Mud Ring Wall Stud Extron XTP T UWP 302 AUDIO IN PWR HDCP HDMI VGA HDMI IN VGA IN Figure 8. Installing the XTP T UWP 302 in a Junction Box 1. A[...]

  • Seite 15

    XTP T UWP 302 • Installation and Operation 9 Fr ont Panel Connections AU DI O IN PW RH DCP HDMI VG A HDMI IN VG A IN ab c Figure 9. Front Panel Connectors a HDMI connectors — Connect a digital video source device to the HDMI connector . It can accept HDMI, DVI, or dual mode DisplayPort video sources. b Audio connector — Connect an analog audi[...]

  • Seite 16

    XTP T UWP 302 • Installation and Operation 10 Making Connections HDMI Connection Use an Extron LockIt Lacing Bracket to secur e an HDMI cable to each connector as follows: 3 3 1 2 4 5 Figure 11. Installing the LockIt Lacing Bracket 1. Plug the HDMI cable into the panel connection. 2. Loosen the HDMI connection mounting screw fr om the panel enoug[...]

  • Seite 17

    XTP T UWP 302 • Installation and Operation 11 TP Cable T ermination and Recommendations Use the following pin configurations for twisted pair cables. 12345678 RJ-45 Connector Inser t T wisted P air Wires Pins: Pin 1 2 3 4 5 6 7 8 Wire color White-green Green White-orange Blue White-blue Orange White-brown Brown Wire color T568A T568B White-orange[...]

  • Seite 18

    XTP T UWP 302 • Installation and Operation 12 RS-232 and IR Over XTP Communication The RS-232 and IR Over XTP connector is for pass-through transmission of serial signals, such as projector contr ol signals, and Infrared data (see figure 13 for an example of how to wire the connector). Tx/Rx Pins Rx Tx RS-232 Rx Tx Tx Rx Rx Tx Custom IR Device RS[...]

  • Seite 19

    XTP T UWP 302 • Installation and Operation 13 Power Connection Apply power to the transmitter locally with the provided power supply or r emotely with a power injector or an XTP matrix switcher . A TTENTION: XTP remote power is intended for indoor use only . No part of the network that uses XTP remote power should be r outed outdoors. Local power[...]

  • Seite 20

    XTP T UWP 302 • Installation and Operation 14 Remote power The XTP T UWP 302 can be powered r emotely through an XTP Power Injector or through an XTP matrix switcher . A TTENTION: XTP remote power is intended for indoor use only . No part of the network that uses XTP remote power should be r outed outdoors. Power injector T o power the XTP T UWP [...]

  • Seite 21

    XTP T UWP 302 • Installation and Operation 15 Operation After all transmitters, all receivers, and their connected devices ar e powered up, the system is fully operational. If any problems ar e encountered, verify that the cables are r outed and connected properly . If problems persist, call the Extron S3 Sales & T echnical Support Hotline. S[...]

  • Seite 22

    XTP T UWP 302 • Installation and Operation 16 Reset Modes Use the recessed Reset button on the r ear panel of the transmitter to return the device to default settings or to restor e factory-shipped firmware. T o access the Reset button, the XTP T UWP 302 may need to be removed fr om the mud ring or junction box. Reset Mode Summary Mode Activation[...]

  • Seite 23

    XTP T UWP 302 • SIS Configuration and Control 17 SIS Configuration and Contr ol The XTP T UWP 302 can be configured and contr olled using Extron Simple Instruction Set (SIS) commands or the XTP System Configuration Software (see XTP System Configuration Software on page 22). This section contains basic SIS communication details and SIS commands a[...]

  • Seite 24

    XTP T UWP 302 • SIS Configuration and Control 18 Error Responses When the XTP T UWP 302 receives an SIS command and determines that it is valid, it performs the command and sends the corresponding r esponse to the host device. If the command is determined invalid or contains invalid parameters, the switcher returns an error response to the host. [...]

  • Seite 25

    XTP T UWP 302 • SIS Configuration and Control 19 Command and Response T ables for SIS Commands Command ASCII Command (Host to Device) Response (Device to Host) Additional Description Input Commands Input selection Select input X! ! In X!] Select input X! . View the selected input ! In X! ] V iew the selected input. Auto switch mode Disable auto s[...]

  • Seite 26

    XTP T UWP 302 • SIS Configuration and Control 20 Command ASCII Command (Host to Device) Response (Device to Host) Additional Description Black signal for audio only NOTE: The switcher uses a black signal to simulate a 720p or 1080p, 50 Hz or 60 Hz signal so audio can be passed without video. Enable black signal E B1AFMT } AfmtB X( ] Enable a blac[...]

  • Seite 27

    XTP T UWP 302 • SIS Configuration and Control 21 Command ASCII Command (Host to Device) Response (Device to Host) Additional Description EDID Commands NOTE: For EDID management, use the XTP System Configuration Software (see EDID Minder on page 33). Advanced Configuration Commands HDCP authorized device (HDMI input only) HDCP authorized device On[...]

  • Seite 28

    XTP T UWP 302 • XTP System Configuration Software 22 XTP System Configuration Softwar e This section contains installation and configuration procedur es for the XTP System Configuration Software for configuring and contr olling the XTP T UWP 302. T opics in this section include: • Installing the XTP System Configuration Software • Using the X[...]

  • Seite 29

    XTP T UWP 302 • XTP System Configuration Software 23 Using the XTP System Configuration Softwar e The XTP T UWP 302 can be controlled dir ectly from the side panel config port or remotely from an XTP matrix switcher . Connections When opening the XTP System Configuration Software, the Connections scr een opens first. This screen is used to establ[...]

  • Seite 30

    XTP T UWP 302 • XTP System Configuration Software 24 T op Menu The top menu bar contains three menus for configuring softwar e settings. File menu The File menu contains options for disconnecting and exiting the program. T o access the menu, click the File menu. Figure 20. File Menu Disconnect This option disconnects the XTP System Configuration [...]

  • Seite 31

    XTP T UWP 302 • XTP System Configuration Software 25 Update Firmware This option uploads firmware fr om the host device to the connected device. NOTE: If necessary , download new firmware fr om the Extron website (see Downloading Firmware on page 37). 1. From the Tools menu, select Update Firmware . A dialog box opens to ask permission to disconn[...]

  • Seite 32

    XTP T UWP 302 • XTP System Configuration Software 26 Help menu The Help menu contains XTP System Configuration Software information, the help file, and a link to the Extron website. Figure 24. Help Menu About the Software This option provides basic information about the XTP System Configuration Softwar e, including version number and copyright in[...]

  • Seite 33

    XTP T UWP 302 • XTP System Configuration Software 27 Device Settings The Device Settings screen allows a user to view and edit various device settings for the device directly connected to the host device. Click the Device Settings icon on the Global Navigation bar to open the Device Settings screen. Figure 26. T ransmitter Device Settings Screen [...]

  • Seite 34

    XTP T UWP 302 • XTP System Configuration Software 28 Input/Output tab Click the Input/Output tab to open the Input/Output screen. It contains input information and options to apply automatic settings to individual inputs. Figure 27. Input/Output T ab Input name — Displays the input name. Signal type — Displays the signal type of each input. I[...]

  • Seite 35

    XTP T UWP 302 • XTP System Configuration Software 29 Analog Video tab Click the Analog Video tab to open the Analog Video screen. It contains signal sampling, image shifting, and saving and recalling input pr eset options. Figure 28. Analog Video T ab Signal Sampling panel Signal sampling optimizes the input signal to the transmitter for the curr[...]

  • Seite 36

    XTP T UWP 302 • XTP System Configuration Software 30 Audio tab Click the Audio tab to open the Audio screen. It contains settings for input format and analog audio gain. Figure 29. Audio T ab Input format section Input format — From the Audio Format dr op-down list, select the format for input 2. It can be Auto , HDMI , or Analog . Analog audio[...]

  • Seite 37

    XTP T UWP 302 • XTP System Configuration Software 31 General tab Click the General tab to open the general screen. It contains settings for executive mode, auto switch mode, and factory reset. Figure 30. General T ab Executive mode section Unlock the front panel — Click the Unlock Front Panel radio button (default) to disable executive mode. Lo[...]

  • Seite 38

    XTP T UWP 302 • XTP System Configuration Software 32 Device Information panel The Device Information panel displays device information and settings. General Information section Model — Displays the device model. Firmware version — Displays the full firmwar e version. Signal Information section Selected input — Displays the input number of t[...]

  • Seite 39

    XTP T UWP 302 • XTP System Configuration Software 33 EDID Minder Use the EDID Minder screen to assign unique EDID to the input or match curr ent output resolutions to the input. Click the EDID Minder icon on the global navigation bar . The EDID Minder screen opens. The EDID Minder screen displays a table of EDID options and connected output devic[...]

  • Seite 40

    XTP T UWP 302 • XTP System Configuration Software 34 Import EDID 1. On the EDID Minder screen, click the Add EDID to Library button. 2. Select the desired EDID file and click Open . The EDID appears in the A vailable EDID pane. 3. Assign the EDID from the A vailable EDID pane to import the EDID setting to the device. Save output EDID 1. On the ED[...]

  • Seite 41

    XTP T UWP 302 • Reference Information 35 Refer ence Information This section contains mounting information and instructions for updating firmware. T opics in this section include: • Updating Firmware with Firmwar e Loader • Mounting T emplate Updating Firmwar e with Firmware Loader T o upload and update firmware for the XTP T UWP 302, downloa[...]

  • Seite 42

    XTP T UWP 302 • Reference Information 36 Figure 34. Navigating to Firmwar e Loader 3. Navigate to Firmware Loader . 4. Click the Download link on the right that corresponds with the pr ogram. 5. Submit any requir ed information to start the download. Note where the file is saved. Installing Firmware Loader 1. Once Firmware Loader has been downloa[...]

  • Seite 43

    XTP T UWP 302 • Reference Information 37 Downloading Firmware Figure 35. Downloading Firmwar e from the Extron W ebsite 1. On the Extron website , click the Download tab. 2. On the left sidebar , click the Firmware link. 3. Navigate to the XTP T UWP 302. 4. Ensure the available firmwar e version is a later version than the current one on the devi[...]

  • Seite 44

    XTP T UWP 302 • Reference Information 38 Installing Firmware with Firmwar e Loader Use the Firmware Loader utility to upload firmwar e to the transmitter when connected directly to the device. 1. Connect the host device to the side panel USB port. 2. Open Firmware Loader and establish a connection between the computer and the device. The Add Devi[...]

  • Seite 45

    XTP T UWP 302 • Reference Information 39 Mounting T emplate Figure 37 is a example of a mounting template for pr eparing mounting surfaces. It is not to full size. T emplate for the 3-gang mounting bracket 6.41" (16.3 cm) 4.50" (11.4 cm) TEMPLA TE IS NOT FULL SIZE. Recommended cut-out area f or the installation surface . T op P anel SUR[...]

  • Seite 46

    Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron Asia +65.6383.4400 +65.6383.4664 F AX Extron Japan +81.3.3511.7655 +81.3.3511.7656 F[...]