Stamina Products 45-1003 manuale d’uso

45-1003 ST AMINA PRODUCTS MADE IN CHINA Product May V ary Slightly From Pictured. Exercise ca n present a health risk. Con sult a physici a n bef ore beginning a ny exercise progra m with this equipment. If you feel faint or dizzy , i mmedi ately discontinue use of this equi pment. Serious bodily injury ca n occur if this equi pment is not a ssembl[...]

T ABLE OF CONTENTS SAFETY INSTRUCTIONS T o reduce the risk of serious in jury , rea d the following Safety Instruction s before using the INMOTION T3000 T rea dmill . W ARNING: Before starting a ny exercise or conditioning progra m you should consult with your personal physici a n to see if you require a complete physical exa m. This is especially [...]

THAN K YOU FOR PURCHASING THE INMOTION T3000 TREADMILL T o help you get started, we have pre-a sse mbled most of your INMOTION T3000 T rea dmill at the fa ctory with the exception of those few parts left un a sse mbled for shi pping purpose s. Simply f ollow the few a ssembly in structions set f orth in this ma nual. With regular workouts you will [...]

BEFORE YOU BEGIN 4 THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBL Y : Wrench Allen Wrench (4mm) Meter Right Upright Moving Wheel Upright Support Side Molding W al king Belt Ba se Fra me U-Sha ped Handrail Left Upright Flywheel Adjustment Bra cket Bumper Sta nd Tha nk you for choosing the INMOTION T3000 T rea dmill . W e ta ke great pride in producing[...]

5 EQUIPMENT W AR NING & NOTICE LABELS This chart is provided to help identify the warning & notice labels on the INMOTION T3000 T rea dmill . Plea se ta ke a moment to fa miliarize yoursel f with all of the warning & notice la bels. La bel is larger tha n a ctual size W AR NING LABEL(46) W1[...]

6 Part No. and De scri ption Qty 35 Bolt, Hex He ad (M12x1.75x75mm) 2 36 Bolt, Button He ad (M6x1x15mm) 2 45 W a sher (M12) 2 41 Arc Wa sher (M6) 2 42 Arc Wa sher (M8) 4 HAR D W ARE IDENTIFICA TION CHAR T This chart is provided to help identify the hardware used in the a ssembly process. Pla ce the wa shers, the ends of the bolts, or screws on the [...]

Pla ce all parts from the box in a cleared area a nd position them on the floor in front of you. Remove all pa cking materi als from your area a nd pla ce the m ba ck into the box. Do not dispose of the pa cking materi als until a ssembly is completed. Re ad ea ch step carefully bef ore beginning. If you are missing a part plea se call our toll-fre[...]

ASSEMBL Y INSTRUCTIONS 8 STEP 2 Pla ce the BASE FRAME(1) between the LEFT a nd RIGHT UPRIGHTS(2, 3) a nd secure with HEX BOL TS(M12x1.75x75mm)(35) and W ASHERS(M12)(45). DO NOT TIGHTEN COMPLETEL Y . STEP 3 Slide down the upper parts of the FOAM GRIPS(22), so you ca n see the screw hole s at the ba ck side of the tops of the LEFT a nd RIGHT UPRIGHTS[...]

ASSEMBL Y INSTRUCTIONS 9 STEP 5 Install two AA batteries into the METER(24), two batteries included. See page 10 f or detailed battery installation instruction s. Slide the METER(24) onto the plate on the U-SHAPED HANDRAIL(5). Connect the UPPER EXTENSION WIRE(26) to the METER(24). STEP 6 Atta ch the BUMPER ST ANDS(20) to the bottom of the BASE FRAM[...]

USING THE ELECTRONIC METER W alking Belt move ment or push the button. Automatic shut off after 4 minute s of in a ctivity . POWER OFF : POWER ON : AA Batterie s MODE / CLEAR BUTTON: Press a nd relea se to select functions. Press a nd hold f or three seconds to reset all functions to zero. SCAN: TIME: SPEED: DIST ANCE: CALORIES: Automatically sca n[...]

The ba sic ide a behind the manual tre admill is to have the belt running on a trea dmill board and between two rollers so that the belt will move without much eff ort. In order for the belt to run smoothly , there are a few points that need to be noted. TREADMILL ADJUSTMENTS BEL T ALIGNMENT The belt must be in the center of the trea dmill to preve[...]

TREADMILL ADJUSTMENTS W ALKING RESIST ANCE The walking re sista nce or eff ort needed to push the trea dmill belt ca n be adjusted by cha nging the incline a ngle. This trea dmill ha s two adjustment position s. Lowe st Re sista nce Remove (unscrew) the BUMPER ST ANDS(20) from the bottom of the trea dmill a nd store them in the end of the trea dmil[...]

ST ORAGE 13 T o store the INMOTION T3000 T rea dmill si mply kee p it in a clea n dry pla ce. T o avoid da mage to the electronics meter , remove the batteries before storing the INMOTION T3000 T re admill for one ye ar or more. Follow the following proce ss to fold The INMOTION T3000 T rea dmill a s illustrated for ea sy storage. 1. 2. 3. 4. UNFOL[...]

PRODUCT P ARTS D RA WING 14 FRONT BACK Belt Guides[...]

P ARTS LIST DIAGRAM# P ART NAME QTY 15 1 Ba se Fra me 1 2 Left Upright 1 3 Right Upright 1 4 Upright Support 1 5 U-Sha ped Ha ndrail 1 6 Pull Pin 1 7 Bumper 1 8 Front Roller /w Flywheels 1 9 Front Shaft 1 10 Bearing (6000zz) 4 1 1 Pla stic Spa cer 4 12 Rear Roller 1 13 Rear Shaft 1 14 Adjustment Bra cket 2 15 W alking Belt 1 16 Board 1 17 Left Side[...]

16 W ARRANTY LIMITED W ARRANTY MODEL 45-1003 Sta mina Products, Inc. warra nts that this product will be free from defects in materi als a nd workma nshi p under normal use, service a nd proper operation for a period of 90 days on the parts a nd one year on the fra me from the date of the original purcha se from a n authorized retailer . THIS W ARR[...]

17 NOTES[...]

IMPORT ANT : Before filling out the form below ma ke sure you have the right information. Refer to the parts list to make sure you're ordering the right parts! Detach a nd M ail or Fax the Form Below Sta mina Products, Inc. P .O. Box 1071 Springfield, MO 65801-1071 IMPORT ANT : We must have your phone number in order to proce ss the order! F A[...]