Network Technologies SM-nXm-AV-LCD manuale d’uso

SM-nXm-AV-LCD Audio/Video Matrix Switch Installation and Operation Manual MAN063 Rev 10/1/03 NTI NETWORK TECHNOLOGI ES INCORPORATE D Te l:33 0-5 62 -70 70 Fax :33 0-5 6 2-1 999 1275 D an ner D r Aurora, OH 44202 www.nt i1.com R VEEMUX TM A Series[...]

WARRANTY INFORMATION The warranty period on this produ ct (parts and labor) is one (1) year from the date of purchase. Please contact Network Technologies Inc at (800) RGB-TECH (800 -742- 8324) or (330) 562-7070 for inform ation regarding repairs and/or returns. A return authorization number is requi red for all repairs/returns. COPYRIGHT Copyright[...]

Table of Contents Introduc tion ........................................................................................................................................................................................ 1 Specific ati ons ................................................................................................................. [...]

1 Introduction The SM-nXm-AV-LCD Audio/Video Matrix s witch (VEEMUX-A) allows up to 32 audio/video sources (n) to be connecte d to up to 16 destinations (m). Different desti nations can even be con nected to the same source. Video resolution up to 1920x1200@85Hz is supported with no degradatio n – guaran teed. Stereo audi o is supported, as well [...]

2 Ordering Information The SM-nXm-AV-LCD Audio/Video Matrix s witch (VEEMUX-A) can be ordered in many sizes and with several control options . The base unit includes a user k eypad and an RS232 port to make up a c omplete system, with an option for an infrared control. The infrared option is purchased se parately, allo wing for maximum user satisfa[...]

3 Features and Functions 1. LCD Display- for visual indication of conn ection between the user and a sp ecific CPU. 2. Keypad- buttons for user control over s witch functions 3. Audio IN- for connection of audio cables from audi o sources 4. Audio OUT- for connection of audio cables to a udio output devices (speakers) 5. Fuse Holder- holder for rep[...]

4 Installation 1. Turn OFF power to all video sources (inputs) that will be connected to the VEEMUX-A before connecti ng or disconnecting any cables. 2. For each video source, connect a VEXT-xx-MM cable from the video p ort of the source to a video input (VIDEO-1) of the VEEMUX-A (see Fig. 1). 3. Repeat step 2 for remaining video sources. 4. For ea[...]

5 6. Connect a monitor to the por t labeled MONITOR 1 on t he rear of the VEEMUX-A (see Fig. 2). 7. Repeat step 6 for remaining monitors (outputs). 8. Connect audio output device (speakers) to port lab eled AUDIO OUT 1. 9. Repeat step 8 for remaining audio outp ut devices, connecting them to any remaini ng AUDIO OUT ports. 10. If using RS232 contro[...]

6 Front Panel Keypad Control The front panel keypad and LC D (drawing below) allo w the user to view and change current audio and vid eo connections, adjust audio volume and configur e the RS-232 control interf ace. The ke ypad buttons perform the following functions. ESC Escape back to the main display. 0 – 9 Used to enter numbers. ( # ) OUT Spe[...]

7 • Connecting v ideo only To make a video connection without changing the current audio connection, use any of the follo wing commands: 1. <OUT>, < ▲ >, Single digit output port number, <IN> or <ENTER>, Single digit input port number, <ENT ER>. Ex: <OUT> < ▲ > 3 <IN > 5 <ENTER> 2. <OUT[...]

8 RS232 Control Remote Connection The RS232 Interface is designed to control the s witch via serial (RS232) daisy chain con nection from any host computer or other controller with an RS232 communications port. T here is, however, a restriction that must be followed: A program must be used that will send an entire co mman d line all at once, not cha[...]

9 Command Protocol Host controller commands supported by t he unit are defined belo w. All commands should be terminated with a <CR> (carriage return). When a command is sent, the entire string is echoed back to the host alon g with a response from the addressed unit as shown in the command definitio ns. All characters should be up per case, [...]

10 CB - Change Baud Rate For All Switches Format: CB 00,BR<CR> Successful Response: None Syntax or Transmission Error: ?<CR> Behavior: All switches on the serial bus will change their baud rat e to the new baud rate. 12 specifies 1200 baud, 24 specifies 2400 baud, 48 specifies 4800 bau d, 96 specifies 9600 baud. RS - Internal Reset This[...]

11 RO - VIDEO Read Connection For Output/User Port Format: RO SW,OP<CR> Successful Response: *<CR> IP<CR> Syntax or Transmission Error: ?<CR> Behavior: This will find out which VIDEO input/CPU port is connected to the specified VIDEO output/us er port. AS - AUDIO Connect One Output/User Port To Input/CPU Port Format: AS SW,I[...]

12 AV - Set Volume Level For Output/User Port Format: AV SW,OP,VV<CR> Successful Response: *<CR> Syntax or Transmission Error: ?<CR> Behavior: On switches that support AUDIO and support volume control of the output/user port, this co mmand will set the volume of th e specified AUDIO output/user port from a scale of 00 to 99, which[...]

13 6) Connect All Aud io Outputs/Users to an Input/CPU - connect all outputs to an input (Audio ports onl y) 7) Change Mut e Status for Audio Output/User - mute or un-mute the Audio port output 8) Change V olume for Audio Output/User - change Audio port output volume 9) Read Connection for KVM Output/User - read what input is connected to the speci[...]

14 1 23 45 67 8 9 10 11 12 13 14 15 16 17 18 19 20 12 34 5 6 78 9 10 11 12 13 14 15 16 IRT-20X16 LO BATT NT I ON OFF I N P U T S O U T P U T S 1. Move ON / OF F switch to the ON position. 2. Select one of the 16 output touch activated buttons. 3. Make sure red LED on the IR receiver is on before sele cting input. 4. Select one of the 20 input touch[...]

15 DDC Support (Optional) DDC information allo ws the CPU to automatic ally select the optimal resolution for the monitor b y receiving, at power up, information from the monitor concerni ng its reso lution specifications. When DDC Support is installed, the DDC info rmatio n is acquired from the monitor by the VEEMUX-A switch when the VEEMUX is pow[...]

16 Rack mounting Instructions This NTI switch was designed to be directly mounted to a ra ck. It includes a mounting fl ange to make attachment easy. Install 4 captive nuts to the rack in locations that line up with the holes (or slots) in the mounting flange on the NTI switch . Then secure the NTI s witch to the rack usin g four 3/16" diamete[...]