Extron electronic DTP DVI 301 manuale d’uso

68-2169-01 Rev. A 12 11 DVI Twisted Pair Extender DTP DVI 301 User Guide DVI & HDMI Extenders[...]

This symbol is intended to alert the user of important operating and mainte- nance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock. Caution Read Instructions ?[...]

FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference r eceived, including interfer ence that may cau[...]

Conventions Used in this Guide In this user guide, the following are used: CAUTION: A caution indicates a potential hazard to equipment or data. NOTE: A note draws attention to important information. TIP: A tip provides a suggestion to make working with the application easier . WARNING: A warning war ns of things or actions that might cause injury [...]

Contents Introduction ............................................ 1 About this Guide ............................................. 1 About the DTP DVI 301 Tx/Rx T ransmitter and Receiver ................................................... 1 T ransmission Distance .................................. 2 TP Cable Advantages ............................[...]

DTP DVI 301 • Contents vi[...]

Intr oduction • About this Guide • About the DTP DVI 301 T ransmitter and Receiver • Features About this Guide This guide describes the Extron DTP DVI 301 Long Distance Digital Visual Interface (DVI) T wisted Pair Extender , which consists of a DTP DVI 301 Tx transmitter and a DTP DVI 301 Rx receiver . This guide describes how to install, ope[...]

The transmitter is shipped with a single external desktop 12 VDC power supply that accepts 100 to 240 V AC, 50-60 Hz input. A single power supply connected to either the transmitter or the receiver can power both units thr ough the TP cable that carries DVI video. TP Cable Advantages T wisted pair cable is much smaller , lighter , more flexible, an[...]

Installation and Operation This section describes the installation and the operation of the DTP DVI 301 Tx/Rx Extender , including: • Mounting the T ransmitter or Receiver • Connections • Operation Mounting the T ransmitter or Receiver CAUTION: Installation and service must be performed by authorized personnel only . Mounting instructions and[...]

c Audio connector — If desired, plug an analog audio input into the transmitter via this stereo mini jack connector . NOTES: • The analog audio input on this connector is in addition to the digital audio that is embedded in the DVI input. • See the figure at right to identify the tip, ring, and sleeve when you are making connections for the t[...]

Receiver Connections . F ron t Rear L R OUTPUTS DVI-D AUDIO DTP DVI 301 Rx Re a R r F F ro t n t Rx Tx RS-232 IR Rx Tx POWER 12V 0.7 A MAX IN ANALOG AUDIO SIG LINK DTP IN 10 9 11 8 7 Figure 3. DTP DVI 301 Rx Connectors g DTP and Analog Audio Input RJ-45 connectors — Connect one end of the one or two separate TP cables from the transmitter output [...]

i Audio output connector — This 5-pole, 3.5 mm captive screw connector outputs the transmitted, unamplified, line level analog audio. Connect an audio device, such as an audio amplifier or powered speakers. See figure 4 to pr operly wir e a captive screw output connector . Use the supplied tie-wrap to strap the audio cable to the extended tail of[...]

Pin Assignments and Wiring DVI connector pin assignments Figure 5 defines the pinout for the DVI connector . Pin Signal 1 TMDS data 2– TMDS data 2+ TMDS data 1– TMDS data 1+ DDC clock +5 V power DDC data TMDS clock+ Ground (+5 V) CEC control* TMDS clock– Hot Plug Detect TMDS data 0– TMDS data 0+ Spare Spare Spare Spare Spare Spare TMDS data[...]

TP cable termination Figure 6 details the r ecommended termination of TP cables with RJ-45 connectors in accordance with either the TIA/EIA T 568A or the TIA/EIA T 568B wiring standar d. 5 Pin 1 2 3 6 7 8 4 Wire color White-green Green White-orange White-blue Orange White-brown Brown Blue Wire color White-green Green White-orange White-blue Orange [...]

T erminating shielded cable The Tx and Rx each include two shielded RJ-45 connectors and a length of self-adhesive shielded tape that you can use to make the STP cables that connect the transmitter and receiver . NOTE: Extron supplies the connectors and the shielded tape. Y ou must supply the CA T 5e, CA T 6, or CA T 6a STP cable. T erminate the ST[...]

Power supply wiring NOTES: • Only one power supply is required. A single power supply connected to either unit in the pair powers both units. • A power supply is included with each transmitter . Figure 10 shows how to wir e the connector . Use the supplied tie-wrap to strap the power cord to the extended tail of the connector . Po wer Supply Ou[...]

RS-232 and IR connector wiring Figure 11 shows how to wir e the RS-232 connector . Ground Recei ve pin on connected unit Tr ansmit pin on connected unit Connected RS-232 and IR Device Pins Tx/Rx Pins Recei ve pin on connected unit Tr ansmit pin on connected unit Rx Tx RS-232 IR Rx Tx Figure 11. RS-232 Connector Wiring NOTE: The length of exposed wi[...]

Refer ence Information This section discusses the specifications, part numbers, and accessories for the DTP DVI 301 Tx/Rx transmitter and receiver . T opics that are covered include: • Specifications • Part Numbers and Accessories • Mounting the T ransmitter or Receiver Specifications NOTES : • This product consists of a transmitter (DTP DV[...]

Audio input Number/signal type ........................ 1 PC level stereo, unbalanced Connectors .................................... (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (gr ound) Impedance ..................................... >10k ohms, DC coupled Nominal level ................................. -10 dBV (316 mV rms) Max[...]

Enclosure dimensions T ransmitter .............................. 1.0" H x 4.3" W x 3.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 7.6 cm D) (Depth excludes connectors.) Receiver ................................... 1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connec[...]

Part Numbers and Accessories T ransmitter/Receiver Pair Part Numbers NOTE: The Tx/Rx is comprised of the transmitter and receiver pair , which are pur chased separately . DTP DVI 301 Model Part Number DTP DVI 301 Tx transmitter 60-1213-12 DTP DVI 301 Rx receiver 60-1213-13 Included Parts These items are included with each DTP DVI 301 transmitter an[...]

Mounting Accessories Mounting kit Part Number RSF 123 3.5-inch deep 1U rack shelf kit (transmitter only) 60-190-20 RSB 123 3.5-inch deep 1U rack shelf (transmitter only) 60-604-21 RSU 126 6-inch deep 1U universal rack shelf kit 60-190-10 RSB 126 6-inch deep 1U basic rack shelf 60-604-11 RSU 129 9.5-inch deep 1U universal rack shelf kit 60-190-01 RS[...]

Extr on W arranty Extron Electr onics warrants this pr oduct against defects in materials and workmanship for a period of three years from the date of pur chase. In the event of malfunction during the warranty period attributable dir ectly to faulty workmanship and/or materials, Extron Electr onics will, at its option, r epair or replace said pr od[...]