Français dropdown-ico

Z Microsystems 14 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Z Microsystems 14. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Z Microsystems 14 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Z Microsystems 14 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Z Microsystems 14 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Z Microsystems 14
- nom du fabricant et année de fabrication Z Microsystems 14
- instructions d'utilisation, de réglage et d’entretien de l'équipement Z Microsystems 14
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Z Microsystems 14 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Z Microsystems 14 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Z Microsystems en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Z Microsystems 14, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Z Microsystems 14, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Z Microsystems 14. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Z Microsystems COMMAND CO N SO L E 1 4 User Manu al FI ELD-READY[...]

  • Page 2

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 1. Use the power and video cables supplied with the Command Console to help prevent interference with radio and television reception. The use of cables and adapters may cause interference with electronic equipment in the vicinity of this unit. 2. This equipment has been tested and found to comply with the limits[...]

  • Page 3

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 ST ARTING POINT 4 Shipment Contents 4 User Manual 4 System Requirements 4 Product Description 5 PREP ARATION 6 INST ALL RAILS 7 INST ALL CONSOLE 8 FINAL ADJUSTMENTS 9 CABLES 9 SETUP 11 Closing Console 12 OPERA TION 13 MONIT OR ADJUSTMENTS 14 REFERENCE 18 TROUBLESHOO TING 20 SPECIFICA TIONS 22 APPENDICES 23 SUPPO[...]

  • Page 4

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 The User Manual comes in two formats: printed hardcopy or CD - ROM. This Manual is also available on the Z Microsystems website (www .zmicro.com). W e recommend you read this manual as follows: Carefully follow the instructions in the Installation and T esting chapter for hookup and initial control settings. Ref[...]

  • Page 5

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 PRODUCT DESCRIPTION The Command Console provides a liquid crystal display , a desk work surface and storage for any size keyboard and mouse in a 3.5" high (2U) standard 19" rack or transit case. Specially de - signed locks on each side of the Command Console hold the compact folded unit securely in pla[...]

  • Page 6

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 TOOLS REQUIRED PRECAUTIONS Required T ools and Equipment  Flathead screwdriver with about 10" shaft.  Phillips screwdriver with about 10" shaft.  Computer Setup Diskette In preparation to install the Com- mand Console, take the following precautionary steps: T urn off the electrical power to y[...]

  • Page 7

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 SLIDE REMOVAL With the Console sitting on a workbench with the front facing towards you, press down to release the Z-Locks on each side of the front of the Console to slide the side rails back. The slide rail will reach a stop about half way back. This is a safety stop to prevent the Console sliding out too far [...]

  • Page 8

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Install Rails Go back on the rear of the cabinet frame, and fully tighten the three Phillips screws ((W) see page 30 - Install hardware) holding the slide extension rail to the cabinet frame. Make sure you hold the slide mounts hard against the rack rail. 8[...]

  • Page 9

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 INST ALL THE COMMAND CONSOLE IN THE SLIDES Pull the two Console slides out until they lock. Hold the Console by each side, with the front toward you. Feed the four cables coming out of the Console back through the cabinet frame. Guide the Console into the slides and slide the Console in until it stops. Simultane[...]

  • Page 10

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Loosen the screws on each of the front Z-Lock mounts. FINAL ADJUSTMENTS OF THE COMMAND CONSOLE Slide the Console partially out. Use a flathead screw driver to slightly move the Z-Locks out away from the Console. Tighten all the screws on the front Z-Lock mounts. Slide the Console in and out to see if it moves sm[...]

  • Page 11

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Close the storage tray top, then place the keyboard and mouse on top of the tray door . Using both hands, gently lift the Console screen by the top bar . Open the storage tray top. Remove the keyboard and mouse. Align the Keyboard and Mouse cable to pass through the recessed access notch. With both hands, press [...]

  • Page 12

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Place the keyboard and mouse inside the tray along with all cables and close door . Using both hands, gently drop the Console screen by the top bar until it lays flat. Remove the keyboard and mouse from top. Open the storage tray top. Press both the Z-Locks down and slide in the console until you hear the positi[...]

  • Page 13

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Oper a tion Switch the Console monitor on by pushing and releasing the power switch marked. T urn on the monitor and then the computer . 13[...]

  • Page 14

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Monitor Adjustments The LCD monitor features an On- Screen Display (OSD) with menus designed to make adjusting the monitor display settings easier . When highlighted, the icons illustrate the control function to assist in identifying which control needs adjustment. Before activation of the OSD menu, the Enter bu[...]

  • Page 15

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 MENU DESCRIPTIONS AUT O ADJUSTMENT Select this control to adjust the size and position automatically . It takes a maximum of 10 seconds to complete. This control allows adjustments to the black level of the display screen. Selection of this control allows making adjustments to the luminosity level of the display[...]

  • Page 16

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Monitor Adjustments MENU DESCRIPTIONS H-SIZE Select this control, then use the and buttons to expand or decrease the image width to horizon- tally fill the display screen. Select this control, then use the and buttons to choose from: English, German (Deutsch), Spanish (Espanol), Italian (Italiano) or French (Fra[...]

  • Page 17

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 A UTO CALIBRA TION PROGRAM This program cooperates with FPMC firmware which automatically adjusts and saves the panel settings, which will fit each support mode. It takes about 50 seconds for auto adjust- ment. F ollow these steps to start the Auto Calibration P rogram: 1. Insert the Auto Calibration diskette in[...]

  • Page 18

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 R ef er ence LED INDICATOR The P ower Management feature of the LCD monitor is comprised of three stages: 1. On (green) 2. Standby , Suspend or Active Off (amber/green) 3. Out of Range (amber) TIMING GUIDE The monitor is a multi-frequency monitor . It operates at horizontal frequencies between 31.25KHz and 60.24[...]

  • Page 19

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 TIMING GUIDE The monitor is not limited to these preset factory-timing modes. In fact, because the monitor is multi-scan- ning, it can accept any signal within its frequency range of 31.25KHz - 60.24KHz horizontal and 56Hz - 75Hz vertical. If it is desired to use one of the preset timing modes, refer to the vide[...]

  • Page 20

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 T r oubleshooting NO POWER  Flip the P ower switch ON. The P ower LED turns on.  Make sure the A/C power cord is securely connected to the power jack and to a power outlet.  Plug another electrical device (like a radio) into the power outlet to verify that the power outlet is supplying the proper voltag[...]

  • Page 21

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 DOUBLE (SPLIT) SCREEN IMAGE  Make sure the graphics card is set to Non-Interlaced mode.  Make sure the input signals are within the LCD monitor s specified frequency range. (Maximum: VESA 1024x768/75Hz, MAC 1024x768/ 75Hz)  Connect the video cable securely .  T ry the LCD monitor with another powe[...]

  • Page 22

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Specifica tions 22 P ower 100 - 240 VAC, 47 - 63Hz, 1.2 A Max W eight 26 lbs. Colors 262,144 Viewing Angle L/R 45/45 Deg . Up/Down. 15/35 Deg . Refresh Rate 1024 x 768 @ 75 Hz Max Display Area 284.9mm (H) x 213.7 mm (V) Operating T emp. 0 to +40 Celsius Storage T emp. -10 to +50 Celsius[...]

  • Page 23

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 A ppendix 23 PIN ASSIGNMENT[...]

  • Page 24

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 NOTE: For image problems, run AUTO SETUP again before consulting this section. In most cases, AUTO SETUP can fix the problems. See the Auto Setup section for details. NOTE: If possible, stay by the computer . The Z Microsystems T echnical Support Representa- tive may wish to go through the problem over the telep[...]

  • Page 25

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 If the Z Microsystems T echnical Support Engineer determines that the product needs to be replaced, a Customer Service representative will issue a Return Material Authorization (RMA) number and return address. An RMA number is required to return a product to Z Microsystems, regard- less of the reason for the ret[...]

  • Page 26

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Y2K COMPLIANCE Z Microsystems has achieved full Y2K Compliance. In late 1997, the company s senior management assigned a Y2K Project T eam that consists of a cross-functional representation from information technology , procurement, manufacturing, test and development, finance, general affairs, engineering, m[...]

  • Page 27

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Dr awings 27[...]

  • Page 28

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Dr awings 28[...]

  • Page 29

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 INST ALL HARD WARE · Install the slide assemblies to the rack by installing three screws (V) to the front and three screws (W) to the rear . · Tighten the hex nuts (U) that were installed in the previous page. · Install the command console (FF) into the rack slides. U . 01-91802 Nut 8-32 Nylon Hex V . 01-9208[...]

  • Page 30

    Doc# 27-0001UM Issued 7/99 Rev . 1.2[...]

  • Page 31

    Doc# 27-0001UM Issued 7/99 Rev . 1.2[...]

  • Page 32

    Doc# 27-0001UM Issued 7/99 Rev . 1.2 Z Microsystems, Inc. 5945 Pacific Center Blvd., Suite 509 San Diego, CA 92121 Phone: (858) 657-1000 Fax; (858) 657-1001 Website: www.zmicro.com Copyright 1999 Z Microsystems, Inc. All Rights Reserved[...]