HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80

Aller à la page of

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server devrait contenir:
- informations sur les caractéristiques techniques du dispositif HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server
- nom du fabricant et année de fabrication HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server
- instructions d'utilisation, de réglage et d’entretien de l'équipement HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service HP (Hewlett-Packard) en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation HP (Hewlett-Packard) HP ProLiant DL320 Generation 5 Server. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    HP Pr oL iant DL3 20 Gener ation 5 S er v er Maint enance and Se r v i ce Gui de Part Number 419195-002 November 2007 (Second Edition)[...]

  • Page 2

    © Copyright 2006, 2007 Hewlett-Packard Develop ment Company, L.P. The information contained herein is subject to chan ge without no tice. The only warranties for HP products and services ar e set forth in the express warranty statements accompanying such produc ts and services. Nothing herei n should be construed as constituting an a dditional w a[...]

  • Page 3

    Contents 3 Con t en t s Customer se lf re pair ...................................................................................................................... 5 Parts only warr anty service .................................................................................................... ..................... 5 Illustrated pa rts cata log [...]

  • Page 4

    Contents 4 Server cabl e routing ........................................................................................................... ..................... 58 Embedded SATA contro ller cable routing ......................................................................................... .......... 58 Optional SAS/SATA cont roller cable rout[...]

  • Page 5

    Customer self repair 5 C ust omer se lf r epair HP products are designed with many Customer Self Repair (CSR) parts to minimi ze repair time and allow for greater flexibility in performing def ective parts re placement. If during the di agnosis period HP (or HP service providers or service partners) iden tifies that the repair can be accomplished b[...]

  • Page 6

    Customer self repair 6 • Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplac ement et main d'œuvre du service vous seront facturés. • Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont é[...]

  • Page 7

    Customer self repair 7 NOTA: alcuni componenti HP non sono progettati per la ri parazione da parte del cl iente. Pe r rispettare la garanzia, HP richiede che queste parti siano sostituite da un c entro di assistenza autorizzato. Tali parti sono identificate da un "No" nel Ca talogo illustrato dei componenti. In base alla disponibilità e [...]

  • Page 8

    Customer self repair 8 anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materiali en, die mit einem CSR- Ersatzteil geliefert werden, könn en Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzu schicken, müssen Sie dies inn erhalb eines vorgegebenen[...]

  • Page 9

    Customer self repair 9 Centro de asistencia técnica de HP y reci birá ayu da telefónica por parte de un técnico. Con el envío de materiales para la sustitución de componente s CSR, HP especificará si los comp onentes defectuosos deberán devolverse a HP. En aquellos casos en los que sea necesario devolver algún componente a HP, deberá hace[...]

  • Page 10

    Customer self repair 10 periode, gewoonlijk vijf (5) werkdagen, retourne ren aan HP. Het defecte onderdeel moet met de bijbehorende documentatie worden geretourneerd in het meeg eleverde verpakkingsmateriaal. Als u het defecte onderdeel niet t erugzendt, kan HP u voor het vervangende onderdeel kosten in rekeni ng brengen. Bij reparatie door de klan[...]

  • Page 11

    Customer self repair 11 Para obter mais informações sobre o programa de re paro feito pelo cliente da HP, entre em contato com o fornecedor de serviços local. Para o prog rama norte-americano, visite o site da HP ( http://www.hp.com/go/selfrepair ). Se r v iço de gar antia a pena s par a peças A garantia limitada da HP pode incluir um serviço[...]

  • Page 12

    Customer self repair 12[...]

  • Page 13

    Customer self repair 13[...]

  • Page 14

    Customer self repair 14[...]

  • Page 15

    Customer self repair 15[...]

  • Page 16

    Illustrated parts catalog 16 Illus tr ated par ts catalog Mechanical components Item Description Spare part number Customer self repair (on page 5 ) 1 Access panel 432934-001 Mandatory 1 2 Front bezel 43293 5-001 Mandatory 1 3 Hard drive blank 413960-001 Mandatory 1 1 Mandatory—Parts for which customer self repair is mandatory. If you request HP [...]

  • Page 17

    Illustrated parts catalog 17 1 Mandatory: Obbligatorie—Parti che devono essere necessariam ente riparate dal cliente. Se il cliente ne affida la riparazione ad HP, deve sostenere le spese di spedi zione e di manodopera per il servizio. 2 Optional: Opzionali—Parti la cui riparazione da parte d el cl iente è facoltativa. Si tratta comunque di co[...]

  • Page 18

    Illustrated parts catalog 18[...]

  • Page 19

    Illustrated parts catalog 19 System components Item Description Spare part number Customer self repair (on page 5 ) System components 4 Fan assembly 432933-001 Optional 2 5 Power supply, 420-W 432932-001 Optional 2 Boards 6 Power button/LED boa rd 432931-001 Optional 2 7 System board 432924-001 Optional 2 8 SAS/SATA backplane 432926-001 Optional 2 [...]

  • Page 20

    Illustrated parts catalog 20 Item Description Spare part number Customer self repair (on page 5 ) f) 3.4-GHz Intel® Pentium® 4 651 p rocessor, 2- MB cache, 800-MHz FSB* 418787-001 Optiona l 2 10 Heatsink 432929-001 Optional 2 11 Memory — — a) 512-MB, PC2-53 00 DDR ECC Unbuffered DIMM 433555-001 Mand atory 1 b) 1-GB, PC2-5300 DDR EC C Unbuffer[...]

  • Page 21

    Illustrated parts catalog 21 Item Description Spare part number Customer self repair (on page 5 ) 25 Optical drive ca ble* 433137-001 Optional 2 26 Diskette drive cable* 433138-001 Optional 2 27 USB cable* 432 938-001 Optional 2 28 Cable ma nagement arm kit* 360105-001 Mandatory 1 29 Rack-mounting hardware kit* 360104-001 Mandatory 1 *Not shown 1 M[...]

  • Page 22

    Illustrated parts catalog 22 3 No: No—Algunos componentes no están diseñados para que puedan ser repa rados por el usuario. Para que el usuario haga valer su garantía, HP pone como condición que un proveed or de servicios autorizado realice la sustitución de estos componentes. Dichos componentes se iden tifican con la palabra “No” en el [...]

  • Page 23

    Removal and replacement procedures 23 R emo v al and r eplacement pr ocedur e s Required tools You need the following item s for some procedures: • T-10/T-15 Torx screwdriver (included with the server) • HP Insight Diagnostics softw are (" HP Insight Diagnostics " on page 62 ) Safety considerations Before performing service proced ure[...]

  • Page 24

    Removal and replacement procedures 24 This symbol on an RJ-45 receptacle indicates a network interface connection. WARNING: To reduce the risk of electric sh ock, fire, or damage to the equipment, do not plug telephone or telecommunicat ions connectors into this receptacle. This symbol indicates the presence of a hot su rface or hot component. If t[...]

  • Page 25

    Removal and replacement procedures 25 Server warnings and cautions Before installing a server, be sure that you understand the following warnings and cautions. WARNING: To reduce the risk of electr ic shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. • Plug the p[...]

  • Page 26

    Removal and replacement procedures 26 2. Disconnect all peripheral cables and po wer cords from the server rear panel. 3. Loosen the thumbscrews that secure the se rver faceplate to the front of the rack. 4. Extend the server on the rack rails unti l the server rail-releas e latches engage. WARNING: To reduce the risk of personal injury or equipmen[...]

  • Page 27

    Removal and replacement procedures 27 6. Disengage the serv er from the rack. For more inform ation, refer to the documentation that ships with the rack mounting option. 7. Place the server on a sturdy, level surface. Access panel WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components t[...]

  • Page 28

    Removal and replacement procedures 28 To replace the component, reverse the r emoval procedure. When adding hard drives to the server, ob serve the following general guidelines: • The system automatically sets all drive numbers. • If only one hard drive is used, install it in the bay with the lowest drive number. • Drives must be the same cap[...]

  • Page 29

    Removal and replacement procedures 29 2. Extend the server from the rack (on page 25 ). 3. Remove the access panel (" Access panel " on page 27 ). 4. Disconnect all cables connected to the SAS/SATA backplane. 5. Remove all hard drives (" Hard drives " on page 27 ). 6. Remove all hard drive blanks (" Hard drive blanks "[...]

  • Page 30

    Removal and replacement procedures 30 3. Remove the access panel (" Access panel " on page 27 ). 4. Remove the air baffle. To replace the component, reverse the r emoval procedure. Fan assembly To remove the component: 1. Power down the server (on page 26 ). 2. Extend the server from the rack (on page 25 ). 3. Remove the access panel (&qu[...]

  • Page 31

    Removal and replacement procedures 31 BBWC battery holder To remove the component: 1. Power down the server (on page 26 ). 2. Extend the server from the rack (on page 25 ). 3. Remove the access panel (" Access panel " on page 27 ). 4. Remove the air baffle (" Air baffle " on page 29 ). 5. Remove the fan assembly (" Fan asse[...]

  • Page 32

    Removal and replacement procedures 32 8. Remove the BBWC holder and battery. To replace the component, reverse the r emoval procedure. Media cage To remove the component: CAUTION: To prevent improper cooling and therma l damage, do not operate the server unless all bays are populated with either a component or a blank. 1. Power down the server (on [...]

  • Page 33

    Removal and replacement procedures 33 9. Remove the media cage. To replace the component, reverse the r emoval procedure. Optical drive To remove the component: CAUTION: To prevent improper cooling and therma l damage, do not operate the server unless all bays are populated with either a component or a blank. 1. Power down the server (on page 26 ).[...]

  • Page 34

    Removal and replacement procedures 34 10. Remove the optical drive. To replace the component, reverse the r emoval procedure. Diskette drive To remove the component: CAUTION: To prevent improper cooling and therma l damage, do not operate the server unless all bays are populated with either a component or a blank. 1. Power down the server (on page [...]

  • Page 35

    Removal and replacement procedures 35 10. Remove the diskette drive. To replace the component, reverse the r emoval procedure. Front video connector To remove the component: CAUTION: To prevent improper cooling and therma l damage, do not operate the server unless all bays are populated with either a component or a blank. 1. Power down the server ([...]

  • Page 36

    Removal and replacement procedures 36 10. Remove the front video connector. To replace the component, reverse the r emoval procedure. Power button/LED board To remove the component: 1. Power down the server (on page 26 ). 2. Extend the server from the rack (on page 25 ). 3. Remove the access panel (" Access panel " on page 27 ). 4. Remove[...]

  • Page 37

    Removal and replacement procedures 37 8. Disconnect the power button/LED board cable. 9. Remove the media cage (" Media cage " on page 32 ). 10. Remove the power button/LED board. To replace the component, reverse the r emoval procedure. Front bezel 1. Power down the server (on page 26 ). 2. Extend the server from the rack (on page 25 ).[...]

  • Page 38

    Removal and replacement procedures 38 3. Remove the serial label pull tab by extending it out, and then pressing on the underside to release it from the chassis. 4. Remove the access panel (" Access panel " on page 27 ). 5. Remove all hard drives (" Hard drives " on page 27 ). 6. Remove all hard drive blanks (" Hard drive b[...]

  • Page 39

    Removal and replacement procedures 39 PCI riser board assembly To remove the component: CAUTION: To prevent damage to the server or ex pansion boards, power down the server and remove all AC power cords before removing or installing the PCI riser board assembly. 1. Power down the server (on page 26 ). 2. Extend the server from the rack (on page 25 [...]

  • Page 40

    Removal and replacement procedures 40 5. Remove any installed expansion boards. To replace the component, reverse the r emoval procedure. Storage controller To remove the component: 1. Power down the server (on page 26 ). 2. Extend the server from the rack (on page 25 ). 3. Remove the access panel (" Access panel " on page 27 ). 4. Discon[...]

  • Page 41

    Removal and replacement procedures 41 6. Remove the storage controll er. To replace the component, reverse the r emoval procedure. PCI Express or PCI-X riser board To remove the component: 1. Power down the server (on page 26 ). 2. Extend the server from the rack (on page 25 ). 3. Remove the access panel (" Access panel " on page 27 ). 4.[...]

  • Page 42

    Removal and replacement procedures 42 DIMMs To remove the component: 1. Power down the server (on page 26 ). 2. Extend the server from the rack (on page 25 ). 3. Remove the access panel (" Access panel " on page 27 ). 4. Open the DIMM slot latches. 5. Remove the DIMM. To replace the component, reverse the r emoval procedure. Memory option[...]

  • Page 43

    Removal and replacement procedures 43 The following table lists som e, but not all, possible configurations. Fo r best performance, HP recommends dual-bank interleaved mode configur ations. Slot 1A Slot 2B Slot 3A Slot 4B Total memory Mode 512 MB — — — 512 MB Single-ba nk 512 MB — 512 MB — 1 GB Dual-bank interleaved 1 GB — — — 1 GB [...]

  • Page 44

    Removal and replacement procedures 44 8. Remove the power supply. To replace the component, reverse the r emoval procedure. Heatsink To remove the component: WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent thermal instability and [...]

  • Page 45

    Removal and replacement procedures 45 6. Remove the heats ink. To replace the component: IMPORTANT: When replacing the heatsink, check the l abel on top to be sure the heatsink is properly oriented. 1. Use the alcohol swab to remove all the existing th ermal grease from the processor. Allow the al cohol to evaporate before continuing. CAUTION: Afte[...]

  • Page 46

    Removal and replacement procedures 46 CAUTION: Heatsink retaining screws should be tigh tened or loosened in diagonally opposite pairs (in an "X" pattern). Do not overtighten the screws as this can damage the board, connectors, or screws. Us e the wrench supplied wi th the system to reduce the possibility of overtightening the screws. 3. [...]

  • Page 47

    Removal and replacement procedures 47 6. Open the processor retaining latch and the processor socket retaining bracket. 7. Using your fingers, remove the failed processor. To replace the component: IMPORTANT: Be sure the processor remains ins ide the processor installation tool.[...]

  • Page 48

    Removal and replacement procedures 48 1. If the processor has separated from the installation tool, carefully re-insert th e proces sor in the tool. 2. Align the processor installation tool with the socket and install the sp are processor. CAUTION: The processor is design ed to fit one way into the socket. Use the alignm ent guides on the processor[...]

  • Page 49

    Removal and replacement procedures 49 3. Press down firmly until the processor in stallation tool clicks and separates from the processor, and then remove the processor installation tool. 4. Close the processor retaining latch and th e processor socket retaini ng bracket. 5. Clean the old thermal grease fr om the heatsink with the alcohol swab. All[...]

  • Page 50

    Removal and replacement procedures 50 6. Apply all the grease to the top of the processor in one of the foll owing patterns to ensure even distribution: CAUTION: Heatsink retaining screws should be tigh tened or loosened in diagonally opposite pairs (in an "X" pattern). Do not overtighten the screws as this can damage the board, connector[...]

  • Page 51

    Removal and replacement procedures 51 2. Remove the server from the rack (on pag e 26 ). 3. Remove the access panel (" Access panel " on page 27 ). 4. Remove the PCI riser board assembly (" PCI riser board assembly " on page 39 ). 5. Remove all DIMMs (" DIMMs " on page 42 ). 6. Remove the air baffle (" Air baffle [...]

  • Page 52

    Removal and replacement procedures 52 13. Using your fingers, remove the processor from the failed system board. CAUTION: To avoid damage to the system board: • Do not touch the processor socket contacts. • Always install the processor socket cover after removing the process or from the socket. • Do not tilt or slide the processor when loweri[...]

  • Page 53

    Removal and replacement procedures 53 2. Prepare the processor socket on the spare syst em board: a. Open the processor retaining latch and the processor socket retaining bracket. b. Remove the processor socket protective cover. 3. Install the processor socket cover onto the pr ocessor socket of the f ailed system board. 4. Install the processor on[...]

  • Page 54

    Removal and replacement procedures 54 5. Close the processor retaining latch and th e processor socket retaini ng bracket. 6. Clean the old thermal grease fr om the heatsink an d the top of the processor with the alcohol swab. Allow the alcohol to evapo rate before continuing.[...]

  • Page 55

    Removal and replacement procedures 55 7. Apply all the grease to the top of the processor in one of the foll owing patterns to ensure even distribution: CAUTION: Heatsink retaining screws should be tigh tened or loosened in diagonally opposite pairs (in an "X" pattern). Do not overtighten the screws as this can damage the board, connector[...]

  • Page 56

    Removal and replacement procedures 56 10. Install the access panel. 11. Power up the server. After you replace the system board, you must re-ent er the server serial number and the product ID. 1. During the server startup se quence, press the F9 key to access RBSU. 2. Select the Advanced Options menu. 3. Select Serial Number . The following warning[...]

  • Page 57

    Removal and replacement procedures 57 5. Remove the battery. IMPORTANT: Replacing the system board battery resets the system ROM to its default configuration. After replacing the battery , reconfigure t he system through RBSU. To replace the component, reverse the r emoval procedure. For more information about battery replacement or prop er disposa[...]

  • Page 58

    Cabling 58 C abling Server cable routing CAUTION: When routing cables, always be sure th at the cables are not in a position where they can be pinched or air flow can be blocked. IMPORTANT: Route the cables without b locking the airflow or other installed com ponents. Use the cable clips installed in the ch assis to manage cable routing. Embedded S[...]

  • Page 59

    Cabling 59 Optional SAS/SATA controller cable routing CAUTION: When routing cables, always be sure th at the cables are not in a position where they can be pinched or air flow can be blocked. Slot 2[...]

  • Page 60

    Cabling 60 Slot 1 Video connector option cable routing[...]

  • Page 61

    Cabling 61 Battery-backed write cache cable routing[...]

  • Page 62

    Diagnostic tools 62 Diagno s ti c tools Troubleshooting resources The HP ProLiant Servers Troubleshoot ing Guide provides simple proced ures for resolving common problems as well as a comprehensive course of action for fault isolation and identification, erro r message interpretation, issue resolution , and software maintenance. To obtain the guide[...]

  • Page 63

    Diagnostic tools 63 NOTE: The current version of SmartStart prov ides the memory spare part numbers for the server. To download the latest version, see the HP w ebsite ( http://www.hp.com/support ). Integrated Management Log The IML records hundreds of events and stores th em in an easy-to-view form. The IML timestamps each event with 1-minute gran[...]

  • Page 64

    Component identification 64 C ompone nt i dentif icati on Front panel components Item Description 1 Serial label pull tab 2 Hard drive bay 1 3 Hard drive bay 2 4 Diskette drive/video connect or bay 5 Optical drive bay 6 Front USB connector 7 Power On/Standby button and system power LED[...]

  • Page 65

    Component identification 65 Front panel LEDs and buttons Item Description Status 1 UID button/LED Blue = Identification is activated. Flashing blue = System is being remotely managed. Off = Identification is deactivated. 2 Internal health LED Green = System health is normal. Amber = System is degraded. To identify the component in a degraded state,[...]

  • Page 66

    Component identification 66 Item Description Status 6 Power On/Standby button and system power LED Green = System is on. Amber = System is shut down, but power is still applied. Off = Power cord is not atta ched, power supply failure has occurred, no power supplies are in stalled, facility power is not available, or the DC-to-DC converter is not in[...]

  • Page 67

    Component identification 67 Slot Type Length Co nnector Interconnect 2 PCI Express Full x8 x8 Optional PCI- X Full 133 MHz/3.3 V 64 bit Rear panel LEDs Item Description Status 1 iLO 2 activity Green = Activity exists. Flashing green = Activity exists. Off = No activity exists. 2 iLO 2 link Green = Link exists. Off = No link exists. 3 10/100/1000 NI[...]

  • Page 68

    Component identification 68 System board components Item Description Item Description 1 PCI Express x8 connector or optional PCI-X 133- MHz connector 13 Diskette drive connector 2 PCI Express x1 connector 14 Fan 3 and 4 connector 3 Video option connector 15 Fan 5 and 6 connector 4 System maintenance switch 16 Fa n 7 and 8 connector 5 NMI switch 17 [...]

  • Page 69

    Component identification 69 Position Default Function S4 Off Off = Normal op eration On = Override RBSU setting and enable diskette boot * S5 Off Off = Power-on password enabled On = Power-on password disabled * S6 Off Off = Normal op eration On = BIOS will clear CMOS and NVRAM * S7 Off Reserved S8 Off Reserved * "On" activates the functi[...]

  • Page 70

    Component identification 70 System board LEDs Item LED description Status 1 Reserved — 2 Overtemperature Amber = System has reached a cautionary or critical temperature level. Off = Temperature is OK. 3 Fan 1 and 2 Amber = One or more fans in this module have failed. Off = All fans in this module are operating normally. 4 Processor Amber = Proces[...]

  • Page 71

    Component identification 71 Item LED description Status 10 DIMM 3 Amber = DIMM has failed. Off = DIMM is operating normally. 11 DIMM 2 Amber = DIMM has failed. Off = DIMM is operating normally. 12 DIMM 1 Amber = DIMM has failed. Off = DIMM is operating normally. 13 Power on Green = System board power is nor mal. Off = System board power has failed.[...]

  • Page 72

    Component identification 72 System LED and Color Internal Health LED Color Status Fan module (amber) Amber A redundant fan has failed. Fan module (red) Red The minimum fan requirements are not being met in one or more of the fan modules. One or more fans h ave failed or are missing. Power supply signal interlock (amber) Red The power supply signal [...]

  • Page 73

    Component identification 73 Item Description 1 Device 1 2 Device 2 Fan assembly location[...]

  • Page 74

    Specifications 74 Sp e c i fica t io n s Environmental specifications Specification Value Temperature Operating 1 10 ° C to 35 ° C (50 ° F to 90 ° F) Non-operating 30 ° C to 60 ° C (-22 ° F to 140 ° F) Maximum rate of temperature change Operating 2,3 10°C/hr (18°F/hr) Non-operating 20°C/hr (36°F/hr) Relative humidity (noncondensing)*** [...]

  • Page 75

    Specifications 75 Specification Value Width 42.62 cm (16.78 i n) Weight (maximum) 12.27 kg (27.0 lb) Weight (no drives installed) 10.91 kg (24.0 lb) Input requirement Rated line voltage 90 VAC to 264 VAC Rated input frequency 47 Hz to 63 Hz Rated input current 6.0 A (100 to 120 VAC) to 3.0 A (200 to 240 VAC ) Rated input power 486 W at 115 V (assum[...]

  • Page 76

    Acronyms and abbreviations 76 A c r on y ms and abbr e v iati ons ACU Array Configuration Utility ADU Array Diagnostics Utility BBWC battery-backed write cache BIOS Basic Input/Output System CMOS complementary metal-oxide semiconduct or CSR Customer Self Repair DDR2 double data rate-2 ECC error checking and correcting iLO 2 Integrated Lights-Out 2 [...]

  • Page 77

    Acronyms and abbreviations 77 NVRAM non-volatile memory PCI peripheral component interface PCI-X peripheral component interconnect ext ended PCIe peripheral component interconnect express POST Power-On Self Test RBSU ROM-Based Setup Utility SAS serial attached SCSI SATA serial ATA SDRAM synchronous dynamic RAM UID unit identification USB universal [...]

  • Page 78

    Index 78 A access panel 16 ADU (Array Diagnostic Utility) 63 air baffle 29 Array Diagnostic Utility (ADU) 63 B battery 19, 56, 68, 69 battery-backed write cache battery holder 31 battery-backed write cache battery pack 31 bezel, front 16, 37 bezel, server 16, 37 blue screen event 69 buttons 64 C cable management arm 19 cables 19, 58, 59 cabling 58,[...]

  • Page 79

    Index 79 Integrated Management Log (IML) 63 interleaving memory configuration 43 internal health LED 65, 71 internal USB connector 72 L LED, DIMM slot 70 LED, drive activity 65 LED, fan 70 LED, iLO NIC 67 LED, overtemperature 70 LED, power on 70 LED, PPM 70 LED, processor 70 LED, UID 65 LEDs 64 LEDs, NIC 67 M management tools 62 mechanical componen[...]

  • Page 80

    Index 80 U UID LED 26, 65, 69 USB connectors 64, 68, 72 utilities 62 V video connector 35, 64, 68 W warnings 25 warranty 5, 16[...]