3Com 3800 manual

® http://www.3com.com/ SuperStack ® II Switch 3800 User Guide Part No. DUA1691-0AAA01 100004-00 Rev . 01 Published April 1998 SW3800.BK Page i Tuesday, May 5, 1998 5:20 PM[...]

ii 3Com Corporation 5400 Bayfront Plaza Santa Clara, California 95052-8145 Copyright © 3Com Corporation, 1998. All rights reserved. No part of this documentation may be repr oduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without permission from 3Com T echnologies. 3Com T [...]

iii VCCI Statement Information T o The User If this equipment does cause interference to radio or television r eception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer ence by one or more of the following measures: ■ Reorient the receiving antenna. ■ Relocate the equipment with[...]

iv SW3800.BK Page iv Tuesday, May 5, 1998 5:20 PM[...]

v C ONTENTS A BOUT T HIS G UIDE Introduction 1 T erminology 1 Finding Information in This Guide 2 Conventions 3 Command Syntax Symbols 4 Line-Editing Commands 5 Related Publications 5 1 S WITCH 3800 O VERVIEW About the Switch 3800 1-1 Summary of Features 1-1 Port Connections 1-3 Full-duplex 1-3 Port Redundancy 1-3 Load Sharing 1-4 Switch Operation [...]

vi 2 I NSTALLATION AND S ETUP Following Safety Information 2-1 Determining the Switch 3800 Location 2-1 Configuration Rules for Ethernet 2-2 Installing the Switch 3800 2-2 Rack Mounting 2-2 Free-Standing 2-3 Stacking the Switch and Other Devices 2-4 Connecting Equipment to the Console Port 2-4 Powering-up the Switch 2-6 Checking the Installation 2[...]

vii Configuring SNMP Settings 3-10 Displaying SNMP Settings 3-12 Resetting and Disabling SNMP 3-12 Checking Basic Connectivity 3-12 Ping 3-12 T raceroute 3-13 Configuring Ports 3-13 Enabling and Disabling Ports 3-13 Configuring Autonegotiation 3-14 10/100 port settings 3-14 Gigabit port settings 3-14 Load Sharing 3-15 Configuring Load Sharing 3[...]

viii Port Commands 4-12 P ACE Commands 4-13 STP Commands 4-14 Basic IP Commands 4-16 IP ARP Commands 4-17 IP Route T able Commands 4-18 ICMP Commands 4-18 RIP Commands 4-20 Logging Commands 4-22 Configuration and Image Commands 4-23 5 V IRTUAL LAN S (VLAN S ) Overview of Virtual LANs 5-1 Benefits 5-1 T ypes of VLANs 5-2 Port-Based VLANs 5-2 Expan[...]

ix Configuring FDB Entries 6-3 FDB Configuration Example 6-3 Displaying FDB Entries 6-3 Removing FDB Entries 6-4 7 S PANNING T REE P ROTOCOL (STP) Overview of the Spanning T ree Pr otocol 7-1 How STP Works 7-3 Initialization 7-3 Stabilization 7-4 Reconfiguration 7-4 Spanning T ree Domains 7-4 Defaults 7-5 STP Configurations 7-6 STP Configurati[...]

x 9 S TATUS M ONITORING AND S TATISTICS Status Monitoring 9-1 Port Statistics 9-4 Port Errors 9-6 Switch Logging 9-7 Local Logging 9-8 Real-time Display 9-8 Remote Logging 9-9 Logging Commands 9-10 RMON 9-11 About RMON 9-11 About the RMON Groups 9-12 Statistics 9-12 History 9-12 Alarms 9-13 Events 9-13 Benefits of RMON 9-13 Improving Ef ficiency [...]

xi Fiber Optic Ports A-3 Lithium Battery A-4 L ’information de Sécurité Importante A-4 Power A-5 Cordon électrique A-6 Fuse A-6 Ports pour fibres optiques A-7 Batterie au lithium A-7 Wichtige Sicherheitsinformationen A-8 Power A-8 Power Cord A-9 Fuse A-9 Faseroptikanschlüsse - Optische Sicherheit A-10 Lithiumbatterie A-11 B T ECHNICAL S PECI[...]

xii G LOSSARY I NDEX 3C OM C ORPORATION L IMITED W ARRANTY SW3800.BK Page xii Tuesday, May 5, 1998 5:20 PM[...]

A BOUT T HIS G UIDE About This Guide provides an overview of this guide, describes guide conventions, tells you where to look for specific information and lists other publications that may be useful. Intr oduction This guide provides the r equired information to install and configur e the SuperStack ® II Switch 3800 (3C16910). This guide is inte[...]

2 A BOUT T HIS G UIDE Finding Information in This Guide This table shows where to find specific information in this guide. Task Location Learning concepts Chapter 1, “Switch 3800 Overview” Installing the Switch 3800 Chapter 2, “Installation and Setup” Appendix A, “Safety Information” Setting up user accounts Chapter 3, “Accessing Th[...]

Conventions 3 Conventions T able 1 and T able 2 list conventions that are used thr oughout this guide. T able 1 Notice Icons Icon Notice Type Alerts you to... Note Important features or instructions Caution Risk of personal injury, system damage, or loss of data Warning Risk of severe personal injury T able 2 T ext Conventions Convention Descriptio[...]

4 A BOUT T HIS G UIDE Command Syntax Symbols Y ou may see a variety of symbols shown as part of the command syntax. These symbols explain how to enter the command, and you do not type them as part of the command itself. T able 3 summarizes command syntax symbols. T able 3 Command Syntax Symbols Symbol Description angle brackets < > Enclose a [...]

Line-Editing Commands 5 Line-Editing Commands T able 4 describes the line-editing commands available using the command-line interface. The command syntax is explained in Chapter 4. Related Publications The Switch 3800 documentation set includes the following: ■ SuperStack II Switch 3800 Quick Reference Guide. Part Number DQA1691-OAAA01. ■ Super[...]

6 A BOUT T HIS G UIDE SW3800.BK Page 6 Tuesday, May 5, 1998 5:20 PM[...]

1 S WITCH 3800 O VERVIEW This chapter describes the following: ■ Switch 3800 features ■ How to use the Switch 3800 in your network configuration ■ Switch 3800 front view ■ Switch 3800 rear view ■ Factory default settings About the Switch 3800 Network managers are curr ently faced with the challenge of creating networks that can provide h[...]

1-2 C HAPTER 1: S WITCH 3800 O VERVIEW ■ Virtual LANs (VLANs) ■ Support for 64 VLANs on a single Switch 3800 ■ Support for IEEE 802.1Q tagging ■ Controls traf fic (including broadcasts) ■ Provides extra security ■ Protocol-sensitive filtering for VLANs ■ Recognition of the Priority Access Control Enabled (P ACE) bit set by 3Com Ethe[...]

Summary of Features 1-3 Port Connections The Switch 3800 has 24 autosensing 10BASE-T/100BASE-TX ports with standard RJ-45 connectors, and supports one Gigabit Ethernet port, and one redundant Gigabit Ethernet port with standard Gigabit Interface Connectors (GBICs). Y ou must have a 3Com-approved GBIC module (such as 3C16911) inserted to make use of[...]

1-4 C HAPTER 1: S WITCH 3800 O VERVIEW In the event that the active main port fails or loses link status, the standby port is automatically activated. When the main port resumes operation, the standby port becomes inactive. This feature can be disabled. Load Sharing Load sharing with Switch 3800 Switches allows the user to increase bandwidth and re[...]

Network Configuration Example 1-5 Priority Access Control Enabled (P ACE) The Switch recognizes the P ACE bit set by 3Com Etherlink ® adapters and other devices supporting P ACE. When enabled, traffic with these bits receives priority service fr om the Switch. Spanning T ree Protocol (STP) The Switch 3800 supports the IEEE 802.1d Spanning T ree P[...]

1-6 C HAPTER 1: S WITCH 3800 O VERVIEW Figure 1-2 Switch 3800 used in a backbone configuration The Switch 1100 on each floor has a 100Mbps full-duplex link to the Switch 3800. A Switch 3300 is connected to a group of servers on one floor of the building. The Switch 3800 routes IP traf fic between the IP subnets on each floor , and also provide[...]

Switch 3800 Front View 1-7 In addition to providing a fast backbone between Ethernet LANs, Gigabit Ethernet equipped file servers and services may be directly attached to the Switch 3800 providing impr oved performance to the Ethernet desktop. Switch 3800 Front View Figure 1-3 shows the Switch 3800 front view . Figure 1-3 Switch 3800 front view Th[...]

1-8 C HAPTER 1: S WITCH 3800 O VERVIEW For more information on 1000BASE-SX and 1000BASE-LX characteristics refer to IEEE Draft P802.3z/D4.2 T ables 38-2 and 38-6. LEDs T able 1-2 describes the LED behavior on the Switch 3800. T able 1-1 Media T ypes and Distances Standard Media Type Mhz/Km Rating Maximum Distance 10BASE-T Category 3 UTP Cable (10Mb[...]

Switch 3800 Rear View 1-9 Switch 3800 Rear View Figure 1-4 shows the Switch 3800 rear view . Figure 1-4 Switch 3800 rear view The rear panel has the following featur es: Power Socket The Switch 3800 automatically adjusts to the supply voltage. The power supply operates down to 90 V . The fuse is suitable for both 110 V AC and 220-240 V AC operation[...]

1-10 C HAPTER 1: S WITCH 3800 O VERVIEW MAC Address This label shows the unique Ethernet MAC address assigned to this device. Console Port The console port (9-pin, “D” type connector) is used to connect a terminal and to carry out local out-of-band management. Factory Defaults T able 1-3 shows the factory defaults for the Switch 3800 features. [...]

2 I NSTALLATION AND S ETUP This chapter describes the following: ■ How to decide where to install the Switch 3800 ■ Ethernet configuration rules ■ How to install the Switch in a rack or free-standing ■ How to connect equipment to the console port ■ How to check the installation using the Power On Self-T est (POST) Following Safety Inform[...]

2-2 C HAPTER 2: I NSTALLATION AND S ETUP ■ W ater or moisture cannot enter the case of the unit. ■ T emperature must be within the range of 0 to 40 degr ees Celsius. ■ Air -flow around the unit and thr ough the vents in the side of the case is not restricted. Y ou should provide a minimum of 25mm (1-inch) clearance. ■ No objects are placed[...]

Installing the Switch 3800 2-3 Figure 2-1 Fitting the mounting bracket 5 Repeat the three pr evious steps for the other side of the Switch. 6 Refer to the instructions that shipped with your rack, runners, shelf or tray to complete the installation of the Switch into the mounting rack. CAUTION: When using rack mounting runners, a shelf, or a tray ,[...]

2-4 C HAPTER 2: I NSTALLATION AND S ETUP Stacking the Switch and Other Devices Up to four units can be placed on top of one another . If mixing Switch 3800, Switch 3000 FX, Switch 1000, Switch 1200, and other SuperStack ® II hubs, the smaller units must be positioned at the top using rubber pads. This section relates only to physically placing the[...]

Connecting Equipment to the Console Port 2-5 Figure 2-2 shows the pin-outs for a 9-pin to RS-232 25-pin null modem cable. Figure 2-2 Null modem cable pin-outs Figure 2-3 shows the pin-outs for a 9-pin to 9-pin PC-A T serial null modem cable. Figure 2-3 PC-A T serial cable pin-outs Screen TxD RxD Ground RTS CTS DSR DCD DTR Cable connector: 9-pin fem[...]

2-6 C HAPTER 2: I NSTALLATION AND S ETUP Powering-up the Switch T o power -up the Switch, follow these steps: 1 Connect the power cable to the Switch. 2 Connect the power cable to the wall outlet. 3 If necessary , tur n the on/off switch to the on position. Checking the Installation After turning on power to the Switch 3800, the device performs a P[...]

Logging on for the First Time 2-7 5 Assign an IP address and subnetwork mask for VLAN default. The example below assigns an IP address of 123.45.67.8 and a subnetwork mask of 255.255.255.0. config vlan default ipaddress 123.45.67.8 255.255.255.0 Y our changes take effect immediately . 6 Save your configuration changes so that they will be in effec[...]

2-8 C HAPTER 2: I NSTALLATION AND S ETUP SW3800.BK Page 8 Tuesday, May 5, 1998 5:20 PM[...]

3 A CCESSING T HE S WITCH This chapter describes the following information that you can use to begin managing the Switch 3800: ■ Security access level overview ■ Configuring the Switch for management ■ Switch management methods ■ Configuring SNMP CAUTION: For configuration changes to be retained through a Switch power cycle or reboot, yo[...]

3-2 C HAPTER 3: A CCESSING T HE S WITCH Administrator Access Level An administrator -level account can view and change all Switch parameters, add and delete users, and change the password associated with any account name. The administrator can disconnect a T elnet management session. If this happens, the user is notified that the session has been [...]

Security Access Levels 3-3 4 Enter the new password at the pr ompt. 5 Re-enter the new password at the pr ompt. 6 Save your changes by typing save Creating a Management Account The Switch can have a total of three management accounts. Y ou can use the default names (admin and user), or you can create new names and passwords for the accounts. Passwo[...]

3-4 C HAPTER 3: A CCESSING T HE S WITCH 3 Enter the new password at the pr ompt. 4 Re-enter the new password at the pr ompt. 5 Save your changes by typing save If you forget your password contact your local technical support representative, who will advise on your next course of action. Viewing Switch Accounts T o view the accounts that have been c[...]

Using Telnet 3-5 Using the Console Interface The command-line interface built into the Switch is accessible by way of the 9-pin, RS-232 console port located on the rear of the unit. For more information on the console port pin-outs, refer to Chapter 2. Once the connection is established, you will see the system prompt and you may log on. Using T el[...]

3-6 C HAPTER 3: A CCESSING T HE S WITCH Y ou can enable BOOTP on a per -VLAN basis by using the following command: enable bootp vlan [<name> | all] Manually Configuring the IP Settings If you are using IP without a BOOTP server , you must enter the IP parameters for the Switch in order for the SNMP Network Manager or T elnet software to comm[...]

Using Telnet 3-7 4 At the password pr ompt, enter the password and press [Return]. When you have successfully logged on to the Switch, the command-line prompt displays the name of the Switch in its pr ompt. 5 Assign an IP address and subnetwork mask for the default VLAN by using the following command config vlan <name> ipaddress <ipaddress[...]

3-8 C HAPTER 3: A CCESSING T HE S WITCH Sample output from the show session command is as follows: 3C16910:2 # sh sess # Login Time User Type Location ============================================================ 0 Tue Mar 10 11:10:53 1998 admin console serial 4 Tue Mar 10 13:11:13 1998 user telnet 192.207.37.168 T erminate the session by typing cle[...]

Using SNMP 3-9 Accessing Switch Agents In order to have access to the SNMP agent r esiding in the Switch, at least one VLAN on the Switch must have an IP address assigned to it. For more information on assigning an IP addr ess, refer to “Manually Configuring the IP Settings,” on page 3-6. Saving Configuration Changes If you make configuratio[...]

3-10 C HAPTER 3: A CCESSING T HE S WITCH Configuring SNMP Settings The following SNMP parameters can be configured on the Switch: ■ Authorized trap receivers — An authorized trap r eceiver can be one or more network management stations on your network. The Switch sends SNMP traps to the trap receiver . Y ou can have a maximum of six trap rece[...]

Using SNMP 3-11 T able 3-4 describes SNMP configuration commands. T able 3-4 SNMP Configuration Commands Command Description config vlan <name> ipaddress <ip_address> {<mask>} Configures an IP address for the VLAN. This is required in order to use an SNMP manager. enable snmp access Allows you to turn on SNMP support for the Swi[...]

3-12 C HAPTER 3: A CCESSING T HE S WITCH Displaying SNMP Settings T o display the SNMP settings configured on the Switch 3800, use the following command: show management This command displays the following information: ■ Enable/disable state for telnet, SNMP , and web access ■ SNMP community strings ■ Authorized SNMP station list ■ SNMP tr[...]

Configuring Ports 3-13 Options for the ping command are described in T able 3-6. T raceroute The traceroute command allows you to trace the r outed path between the Switch and a destination endstation. The traceroute command syntax is as follows: traceroute <ip_address> where ip_address is the IP address of the destination endstation. Config[...]

3-14 C HAPTER 3: A CCESSING T HE S WITCH Configuring Autonegotiation By default, the Switch 3800 is configured to use autonegotiation for all ports. Autonegotiation on 10/100 Mbps ports is used to automatically determine speed and duplex settings. Y ou can select to manually configure the duplex and speed settings of 10/100 Mbps ports. Manual co[...]

Load Sharing 3-15 Load Sharing Load sharing with the Switch 3800 allows you to increase bandwidth and resilience by using a gr oup of ports to carry traffic in parallel between Switches. The sharing algorithm allows the Switch to use multiple ports as a single logical port. For example, VLANs see the load-sharing group as a single virtual port. Th[...]

3-16 C HAPTER 3: A CCESSING T HE S WITCH When you define a load-sharing group, you assign a gr oup of ports to a single, logical port number . T o enable or disable a load-sharing group, use the following commands: enable sharing <master_port> grouping <portlist> disable sharing <master_port> The following example defines a load[...]

SmartRedundancy 3-17 SmartRedundancy SmartRedundancy for the Switch 3800 refers to fail-over behavior of the main and standby Gigabit Ethernet ports. SmartRedundancy allows the Switch to always use the main link if it is available. For example, if only the standby link is available it will be used, but if the main link becomes available again the l[...]

3-18 C HAPTER 3: A CCESSING T HE S WITCH disable smartredundancy <portlist> Allows you to disable the SmartRedundancy feature. If the feature is disabled, the Switch changes the active link only when the current active link becomes inoperable. show port <portlist> config Displays state, link status, speed, and autonegotiation setting fo[...]

4 C OMMANDS This chapter contains a description of each command-line interface command for the Switch 3800. It also provides the following information related to Switch 3800 commands: ■ Command syntax ■ Line-editing commands ■ Command history substitution If an asterisk (*) appears in front of the command-line pr ompt, it indicates that you h[...]

4-2 C HAPTER 4: C OMMANDS If the command does not include a parameter , skip to Step 3. If the command requir es more information, or if you want to include optional parameters, continue to Step 2a. a If the command has additional parameters include them after the command name. b If the command includes a parameter , enter the parameter name, and i[...]

Understanding the Command Syntax 4-3 config vlan engineering add port 1-3,6 could use the following shortcut: config engineering add port 1-3, 6 Numerical Ranges Commands that requir e you to enter one or more port numbers use the parameter , <portlist>, in the syntax. A portlist can be a range of numbers, for example: port 1-3 Y ou can add a[...]

4-4 C HAPTER 4: C OMMANDS Line-Editing Commands T able 4-2 describes the line-editing commands available using the command-line interface. vertical bar | Separates mutually exclusive items in a list, one of which must be entered. For example, in the syntax config snmp community [read | write] <string> you must specify either the read or write[...]

Command History Substitution 4-5 Command History Substitution The Switch 3800 “remembers” the last 50 commands you enter . Y ou can display a list of these commands by typing history Common Commands T able 4-3 describes common commands used to manage the Switch. Commands specific to a particular feature ar e described in the other chapters of [...]

4-6 C HAPTER 4: C OMMANDS Switch 3800 Commands The tables in this section list all of the commands used on the Switch 3800. The commands are organized by the following categories: ■ General Switch commands ■ User account commands ■ Switch management commands ■ VLAN commands ■ Protocol commands ■ FDB commands ■ Port commands ■ P ACE [...]

Switch 3800 Commands 4-7 General Switch Commands T able 4-4 describes general Switch commands. T able 4-4 General Switch Commands Command Description show switch Displays the current Switch information, including: ■ sysName, sysLocation, sysContact ■ MAC address ■ current date and time, and system uptime ■ operating environment (temperature[...]

4-8 C HAPTER 4: C OMMANDS User Account Commands T able 4-5 describes user account commands. config devicemode [bridging | iprouting] Allows you to configure the operating mode of the Switch. Specify: ■ bridging — Layer 2 bridging functions only ■ iprouting — Bridging and IP unicast routing functions If this command is used while the Switch [...]

Switch 3800 Commands 4-9 Switch Management Commands T able 4-6 describes Switch management commands T able 4-6 Switch Management Commands Command Description show management Displays network management configuration and statistics including enable/disable states for Telnet and SNMP, SNMP community strings, authorized SNMP station list, SNMP trap re[...]

4-10 C HAPTER 4: C OMMANDS VLAN Commands T able 4-7 describes VLAN commands. config snmp syscontact <string> Allows you to configure the name of the system contact. A maximum of 32 characters is allowed. config snmp sysname <string> Allows you to configure the name of the Switch. The sysname appears in the command line interface prompt.[...]

Switch 3800 Commands 4-11 Protocol Commands T able 4-8 describes protocol commands. FDB Commands T able 4-9 describes FDB commands. T able 4-8 Protocol Commands Command Description show protocol {<protocol_name> | all} Allows you to display protocol-related information, including: ■ Protocol name ■ List of protocol fields ■ List of VLAN[...]

4-12 C HAPTER 4: C OMMANDS Port Commands T able 4-10 describes port commands. create fdbentry <mac_address> vlan <name> <portlist> Allows you to create a permanent FDB entry. Specify the following: ■ mac_address — Device MAC address, using colon separated bytes. ■ name — VLAN associated with MAC address. ■ portlist — P[...]

Switch 3800 Commands 4-13 P ACE Commands T able 4-11 describes P ACE commands. config port <portlist> auto off {speed [10 | 100]} duplex [half | full] Allows you to change the configuration of a group of 10/100 Mbps ports. Specify the following: ■ auto off — The port will not autonegotiate the settings. ■ speed — The speed of the port[...]

4-14 C HAPTER 4: C OMMANDS STP Commands T able 4-12 describes STP commands. T able 4-12 STP Commands Command Description show stpd {<stpd_name> | all} Displays STP information for one or all STPDs on the Switch. show stpd <stpd_name> port <portlist> Displays port-specific STP information, including the forwarding state of each por[...]

Switch 3800 Commands 4-15 config stpd <stpd_name> port cost <value> <portlist> Allows you to specify the path cost of the port in this STPD. The range is 1–65,535. The Switch automatically assigns a default path cost of 1. config stpd <stpd_name> port priority <value> <portlist> Allows you to specify the priori[...]

4-16 C HAPTER 4: C OMMANDS Basic IP Commands T able 4-13 describes basic IP commands. T able 4-13 Basic IP Commands Command Description show ipconfig {vlan [<name> | all]} Displays configuration information for one or more VLANs, including the following: ■ IP address, subnet mask ■ IP forwarding information ■ BOOTP configuration ■ VLA[...]

Switch 3800 Commands 4-17 IP ARP Commands T able 4-14 describes IP ARP commands. disable bootp vlan [<name> | all] Allows you to disable the generation and processing of BOOTP packets. enable bootprelay Allows you to enable the BOOTP relay function on the router. disable bootprelay Allows you to disable the BOOTP relay function on the router.[...]

4-18 C HAPTER 4: C OMMANDS IP Route T able Commands T able 4-15 describes IP route table commands. ICMP Commands T able 4-16 describes the commands used to configure the ICMP protocol. T able 4-15 IP Route T able Commands Command Description show iproute {vlan {<name> | all | permanent | <ipaddress> <netmask>} Allows you to displ[...]

Switch 3800 Commands 4-19 enable icmp useredirects Allows you to enable the modification of route table information when an ICMP redirect message is received. The default setting is disabled. disable icmp useredirects Allows you to disable the changing of routing table information when an ICMP redirect message is received. enable irdp {vlan <nam[...]

4-20 C HAPTER 4: C OMMANDS RIP Commands T able 4-17 describes the commands used to configure the RIP protocol. T able 4-17 RIP Commands Command Description show rip {vlan <name> | all} Displays RIP configuration and statistics for one or more VLANs. Display includes the state for RIP settings, and interface states. Statistics include the fol[...]

Switch 3800 Commands 4-21 enable rip exportstatic Allows you to enable the advertisement of static routes using RIP. The default setting is enabled. disable rip exportstatic Allows you to disable the filtering of static routes. config rip updatetime {<delay>} Allows you to change the periodic RIP update timer. The default setting is 30 second[...]

4-22 C HAPTER 4: C OMMANDS Logging Commands T able 4-18 describes Switch logging commands. T able 4-18 Logging Commands Command Description show log config Displays the log configuration, including the syslog host IP address, the priority level of messages being logged locally, and the priority level of messages being sent to the syslog host. show [...]

Switch 3800 Commands 4-23 Configuration and Image Commands T able 4-19 describes configuration and image commands. config syslog <ipaddress> <facility> {<priority>} {<subsystem>} Allows you to configure the syslog host address and filter messages sent to the syslog host. Options include: ■ ipaddress — The IP address of[...]

4-24 C HAPTER 4: C OMMANDS download image <ipaddress> <filename> {primary | secondary} Allows you to download a new image from a TFTP server. You must specify the IP address of the TFTP server and the image filename. You can optionally specify if you want the file downloaded to the primary or secondary image. If you do not specify, the [...]

5 V IRTUAL LAN S (VLAN S ) Setting up Virtual Local Area Networks (VLANs) on the Switch 3800 eases many time-consuming tasks of network administration while increasing ef ficiency in network operations. This chapter describes the VLAN concepts and explains how to implement VLANs on the Switch 3800. Overview of Virtual LANs A VLAN is a group of loc[...]

5-2 C HAPTER 5: V IRTUAL LAN S (VLAN S ) ■ It helps to control traf fic. W ith traditional networks, congestion can be caused by broadcast traffic that is dir ected to all network devices, regardless of whether they requir e it. VLANs increase the efficiency of your network because each VLAN can be set up to contain only those devices that nee[...]

Overview of Virtual LANs 5-3 For example, in Figure 5-1, the VLANs are configur ed as followings: ■ Ports 3, 6, and 17 are part of VLAN Marketing ■ Ports 13, 16, and 20 are part of VLAN Sales ■ Ports 21 and 24 are part of VLAN Finance Figure 5-1 Example of a port-based VLAN Even though they are physically connected to the same Switch, in or [...]

5-4 C HAPTER 5: V IRTUAL LAN S (VLAN S ) Expanding Port-Based VLANs Across Switches T o create a port-based VLAN that spans two Switches you must do two things: ■ Assign the port on each Switch to the VLAN. ■ Cable the two Switches together using one port on each Switch per VLAN. Figure 5-2 illustrates a single VLAN that spans two Switches. All[...]

Overview of Virtual LANs 5-5 Figure 5-3 illustrates two VLANs spanning two Switches. On Switch 1, ports 1–16 are part of VLAN Accounting ; ports 17–24 ar e part of VLAN Engineering . On Switch 2, ports 1–16 are part of VLAN Accounting ; ports 17–24 are part of VLAN Engineering . VLAN Accounting spans Switch 1 and Switch 2 by way of a connec[...]

5-6 C HAPTER 5: V IRTUAL LAN S (VLAN S ) T agged VLANs The Switch 3800 uses the IEEE 802.1Q D4 draft standard for rules associated with VLAN tagging. T agging is a process that inserts a marker (called a tag ) into the Ethernet frame. The tag contains the identification number of a specific VLAN, called the VLANid . Uses of T agged VLANs T agging[...]

Overview of Virtual LANs 5-7 Figure 5-4 illustrates the physical view of a network that uses tagged and untagged traffic. Figure 5-4 Physical diagram of tagged and untagged traf fic Figure 5-5 shows a logical diagram of the same network. Figure 5-5 Logical view of tagged and untagged traf fic Switch 1 Switch 2 = Marketing = Sales M S = Tagged po[...]

5-8 C HAPTER 5: V IRTUAL LAN S (VLAN S ) In Figure 5-4 and Figure 5-5: ■ The trunk port on each Switch carries traffic for both VLAN Marketing and VLAN Sales . ■ The trunk port on each Switch is tagged. ■ The server connected to port 1 on Switch 1 has a NIC that supports 802.1Q tagging. ■ The server connected to port 1 on Switch 1 is a mem[...]

Overview of Virtual LANs 5-9 The IP traffic has been divided into two IP subnets, 192.207.35.0 and 192.207.36.0. The subnets are internally routed by the Switch 3800. The subnets are assigned dif ferent VLAN names, Finance and Personnel , respectively . The remainder of the traf fic belongs to the VLAN named MyCompany . All ports are members of t[...]

5-10 C HAPTER 5: V IRTUAL LAN S (VLAN S ) Defining Protocol Filters If necessary , you can define a customized protocol filter based on EtherT ype, LLC, and/or SNAP . Up to six filters may be part of a protocol filter . T o define a protocol filter , do the following: ■ Create a pr otocol using the following command: create protocol <pr[...]

Configuring VLANs on the Switch 3800 5-11 The Default VLAN The Switch 3800 ships with one default VLAN that has the following properties: ■ The VLAN name is default. ■ It contains all the ports on a new or initialized Switch. ■ The default VLAN is untagged, and has no VLANid or protocol filter assigned. Configuring VLANs on the Switch 3800 [...]

5-12 C HAPTER 5: V IRTUAL LAN S (VLAN S ) T able 5-1 describes the commands used to configure a VLAN. VLAN Configuration Examples The following example creates a port-based VLAN named accounting , assigns the IP address 132.15.121.1, and assigns ports 1, 2, 3, and 6 to it: create vlan accounting config accounting ipaddress 132.15.121.1 config acc[...]

Displaying VLAN Settings 5-13 The following example creates a tag-based VLAN named video . It assigns the VLANid 1000. Ports 4–8 are added as tagged ports to the VLAN. create vlan video config video tag 1000 config video add port 4-8 tagged The following example creates a VLAN named Sales , with the VLANid 120. The VLAN uses both tagged and untag[...]

5-14 C HAPTER 5: V IRTUAL LAN S (VLAN S ) ■ Status for each port ■ Enabled/disabled ■ T agged/untagged ■ Protocol information ■ IP address ■ STPD information Sample output from this command is as follows: 3C16910:7 # sh vlan all VLAN "Default" created by user Tagging: 802.1Q Tag 1 IP: 192.207.37.214/255.255.255.0 STPD: Domain [...]

Deleting and Resetting VLANs 5-15 Sample output from this command is as follows: show protocol all Protocol Name Type Value ----------------- ---- ----- IP etype 0x0806 etype 0x0800 ipx etype 0x8137 netbios 11c 0xf0f0 decnet etype 0x6004 etype 0x6003 This show command displays protocol information, including the following: ■ Protocol name ■ Lis[...]

5-16 C HAPTER 5: V IRTUAL LAN S (VLAN S ) SW3800.BK Page 16 Tuesday, May 5, 1998 5:20 PM[...]

6 S WITCH F ORWARDING D ATABASE (FDB) This chapter describes the contents of the Switch forwarding database (FDB), how the FDB works, and how to configure the FDB. Overview of the FDB The Switch 3800 maintains a database of all addresses r eceived on all of its ports. It uses the information in this database to decide whether a frame should be for[...]

6-2 C HAPTER 6: S WITCH F ORWARDING D ATABASE (FDB) ■ Permanent entries — Permanent entries are r etained in the database if the Switch is reset or a power of f/on cycle occurs. The system administrator must make entries permanent. A permanent entry can either be a unicast or multicast MAC address. All entries entered by way of the command-line[...]

Configuring FDB Entries 6-3 Configuring FDB Entries T o configure entries in the FDB, use the commands listed in T able 6-1. FDB Configuration Example This example adds a permanent entry to the FDB: create fdbentry 02:60:8c:12:34:56 vlan marketing port 4 The permanent entry has the following characteristics: ■ MAC address is 02608c123456 ■ V[...]

6-4 C HAPTER 6: S WITCH F ORWARDING D ATABASE (FDB) ■ portlist — displays the entries for one or more ports ■ permanent — displays all permanent entries The following sample output shows the information displayed when you request output for all FDB entries: show fdb Hash Num Mac Vlan Flags Ptag Portlist -------------------------------------[...]

7 S PANNING T REE P ROTOCOL (STP) Using the Spanning T ree Protocol (STP) functionality of the Switch 3800 makes your network more fault tolerant. The following sections describe STP concepts, and how STP features ar e supported by the Switch. STP is a part of the 802.1d bridge specification defined by the IEEE Computer Society . T o explain STP [...]

7-2 C HAPTER 7: S PANNING T REE P ROTOCOL (STP) Figure 7-1 Network with an illegal topology This configuration is illegal because it creates loops that cause the network to overload. However , STP allows you to use this configuration because STP detects duplicate paths and immediately prevents (or blocks ) one of them from forwar ding traffic. F[...]

Overview of the Spanning Tree Protocol 7-3 If the link through Bridge C fails, as shown in Figur e 7-3, the STP system reconfigur es the network so that traffic from segment 2 flows through Bridge B. Figure 7-3 T raffic flowing thr ough Bridge B How STP Works STP has the following thr ee stages of operation: ■ Initialization ■ Stabilizatio[...]

7-4 C HAPTER 7: S PANNING T REE P ROTOCOL (STP) The Root Bridge generates BPDUs on all ports at a regular interval known as the Hello T ime. All other bridges in the network have a Root Port. This is the port that costs the least in getting to the Root Bridge, and it is used for receiving the BPDUs initiated by the Root Bridge. Stabilization After [...]

Spanning Tree Domains 7-5 ■ W ithin any given STPD, all VLANs belonging to it use the same spanning tree. Care must be taken to ensure that STPD instances within a single Switch do not see each other in the same broadcast domain. This could happen if, for example, another external bridge is used to connect VLANs belonging to separate STPDs. Defau[...]

7-6 C HAPTER 7: S PANNING T REE P ROTOCOL (STP) STP Configurations When you assign VLANs to an STPD, pay careful attention to the STP configuration and its effect on the forwar ding of VLAN traffic. Figure 7-4 illustrates a network that uses VLAN tagging for trunk connections. The following four VLANs have been defined: ■ Sales is defined on[...]

STP Configurations 7-7 When the Switches in this configuration start up, STP configures each STP domain such that there ar e no active loops in the topology . STP could configure the topology in a number of ways to make it loop-fr ee. In Figure 7-4, the connection between Switch A and Switch B is put into blocking state, and the connection betwe[...]

7-8 C HAPTER 7: S PANNING T REE P ROTOCOL (STP) STP Configurations to A void W ithin a single STPD, you must be careful when configuring your VLANs. The following figures illustrate networks that have been incorrectly set up so that the STP configuration disables the ability of the Switches to forward VLAN traf fic. The tag-based network in Fig[...]

Creating STP Domains 7-9 Figure 7-6 shows a similar configuration in which the VLANs are all port-based. The trunk connections between the Switches requir e one trunk port per Switch for each VLAN. Figure 7-6 Port-based STP configuration T o remove all the bridging loops, STP may block traf fic on the VLAN Sales trunk between Switch 1 and Switch[...]

7-10 C HAPTER 7: S PANNING T REE P ROTOCOL (STP) Enabling STP on the Switch T o enable STP for one or mor e STP domains on your Switch, use the following command at the administrator prompt: enable stpd [<stpd_name> | all] Configuring STP Y ou can configure the following STP parameters for each STPD on the Switch: ■ Hello T ime ■ Forwar[...]

Configuring STP 7-11 config stpd <stpd_name> delete vlan [<name> | all] Allows you to remove one or all VLANs from an STPD. If all is specified, the association between the STPD and VLAN is removed, but both still exist. config stpd <stpd_name> hellotime <value> Allows you to specify the time delay (in seconds) between the t[...]

7-12 C HAPTER 7: S PANNING T REE P ROTOCOL (STP) Configuration Example The following example creates and enables an STPD named Backbone_st . It assigns the Manufacturing VLAN to the STPD. It disables STP on ports 1 through 3, and port 4. create stpd backbone_st config stpd backbone_st add vlan manufacturing enable stpd backbone_st disable stpd bac[...]

Displaying STP Settings 7-13 Sample output from the command is as follows: 3C16910:28 # sh stpd s0 po 5-8 Stpd: s0 Port: 8 PortId: 8008 Stp: ENABLED Path Cost: 4 Port State: FORWARDING Topology Change Ack: FALSE Port Priority: 128 Designated Root: 80:00:08:00:4e:2c:13:00 Designated Cost: 0 Designated Bridge: 80:00:08:00:4e:2c:13:00 Designated Port [...]

7-14 C HAPTER 7: S PANNING T REE P ROTOCOL (STP) Disabling and Resetting STP T o disable STP or return STP settings to their defaults, use the commands listed in T able 7-2. CAUTION: If you ignore warnings and delete an STPD without removing all of its VLAN members first, those VLANs will also be deleted. T able 7-2 STP Disable and Reset Commands [...]

8 IP U NICAST R OUTING This chapter describes how to configure IP r outing on the Switch 3800. It assumes that you are alr eady familiar with IP unicast routing. If not, refer to the following publications for additional information: RFC 1058 — Routing Information Protocol RFC 1256 — ICMP Router Discovery Messages RFC 1723 — RIP V ersion 2 R[...]

8-2 C HAPTER 8: IP U NICAST R OUTING In Figure 8-1, a Switch 3800 is shown with two VLANs defined: Finance and Personnel . Ports 1 and 3 are assigned to Finance ; ports 2 and 4 are assigned to Personnel . Finance belongs to the IP network 192.207.35.0; the router interface for Finance is assigned the IP addr ess 192.206.35.1. Personnel belongs to [...]

Overview of IP Unicast Routing 8-3 Dynamic Routes Dynamic routes ar e typically lear ned by way of RIP . Routers using RIP exchange information in their routing tables in the form of RIP advertisements. Using dynamic routes, the r outing table contains only networks that are r eachable. Dynamic routes ar e aged out of the table when a RIP update fo[...]

8-4 C HAPTER 8: IP U NICAST R OUTING Configuring IP Unicast Routing This section describes the commands associated with configuring IP unicast routing on the Switch 3800. Configuring r outing involves the following steps: ■ V erify the Switch operating mode is set to “iprouting” by using the following command: show switch If it is not, use[...]

Verifying the IP Unicast Routing Configuration 8-5 V erifying the IP Unicast Routing Configuration Use the “show iproute” command to display the curr ent configuration of IP unicast routing for the Switch, and for each VLAN. The “show iproute” command displays the curr ently configured routes, including how each route was learned. Additi[...]

8-6 C HAPTER 8: IP U NICAST R OUTING T able 8-1 describes the commands used to configure basic IP settings on the Switch. T able 8-1 Basic IP Commands Command Description enable bootp {vlan <name> | all} Enables the generation and processing of BOOTP packets on a VLAN to obtain an IP address for the VLAN from a BOOTP server. The default sett[...]

Configuring DHCP/BOOTP Relay 8-7 T able 8-2 describes the commands used to configure the IP route table. T able 8-3 describes the commands used to configure RIP . clear ipfdb [<ipaddress> | vlan <name> | all] Removes the dynamic entries in the IP forwarding database. T able 8-1 Basic IP Commands (continued) Command Description T able [...]

8-8 C HAPTER 8: IP U NICAST R OUTING enable rip splithorizon Enables the split horizon algorithm for RIP. Default setting is enabled. enable rip triggerupdate Enables triggered updates. Triggered update s are a mechanism for immediately notifying a router’s neighbors when the router adds or deletes routes, or changes the metric of a route. The de[...]

Configuring DHCP/BOOTP Relay 8-9 T able 8-4 describes the commands used to configure the ICMP protocol. disable rip splithorizon Disables split horizon. disable rip poisonreverse Disables poison reverse. disable rip triggerupdate Disables triggered updates disable rip exportstatic Disables the filtering of static routes. unconfig rip {vlan <nam[...]

8-10 C HAPTER 8: IP U NICAST R OUTING Routing Configuration Example Figure 8-2 illustrates a Switch that has three VLANs defined as follows: ■ Finance ■ Protocol-sensitive VLAN using the IP pr otocol ■ Ports 1 and 3 have been assigned ■ IP address 192.207.35.1 ■ Personnel ■ Protocol-sensitive VLAN using the IP pr otocol ■ Ports 2 an[...]

Routing Configuration Example 8-11 Figure 8-2 Unicast Routing Configuration Example In this configuration, all IP traffic fr om stations connected to ports 1 and 3 have access to the router by way of the VLAN Finance . Ports 2 and 4 reach the r outer by way of the VLAN Personnel . All other traffic (NetBIOS) is part of the VLAN MyCompany . The [...]

8-12 C HAPTER 8: IP U NICAST R OUTING Displaying Router Settings T o display settings for various IP routing components, use the commands listed in T able 8-5. T able 8-5 Router Show Commands Command Description show ip config {vlan <name> | all} Displays configuration information for one or more VLANs, including the following: ■ IP address[...]

Resetting and Disabling Router Settings 8-13 Resetting and Disabling Router Settings T o return router settings to their defaults and disable r outing functions, use the commands listed in T able 8-6. show rip stat {vlan <name> | all} Displays RIP-specific statistics. Statistics include the following per interface: ■ Packets transmitted ■[...]

8-14 C HAPTER 8: IP U NICAST R OUTING disable rip {vlan <name> | all} Disables RIP for one or more VLANs. When RIP is disabled, the parameters are not reset to their defaults, and the states are not cleared. Disables RIP for a VLAN causes all routes learned from that VLAN to be advertised with a GarbageTime metric of 16, before being deleted [...]

9 S TATUS M ONITORING AND S TATISTICS This chapter describes how to view the current operating status of the Switch, how to display information in the Switch log, and how to take advantage of the RMON capabilities available in the Switch. Viewing statistics on a regular basis allows you to: ■ Monitor how well your network is performing ■ Monito[...]

9-2 C HAPTER 9: S TATUS M ONITORING AND S TATISTICS show ip config {vlan <name> | all} Displays configuration information for one or more VLANs, including the following: ■ IP address, subnet mask ■ IP forwarding information ■ BOOTP configuration ■ VLAN name, VLANid show iparp {<ip_address> | vlan <name> | all | permanent} [...]

Status Monitoring 9-3 show port <portlist> collisions Displays collision statistics for each port. show port <portlist> config Displays state, link status, speed, and autonegotiation setting for each port. show port <portlist> errors Displays error information for one or more ports. show port <portlist> packet Displays a his[...]

9-4 C HAPTER 9: S TATUS M ONITORING AND S TATISTICS Port Statistics The Switch 3800 provides a facility for viewing port statistic information. The summary information lists values for the current counter against every port on the Switch and it is refr eshed approximately every 2 seconds. V alues are displayed to 9 digits of accuracy . T o view por[...]

Port Statistics 9-5 The following port statistic information is collected by the Switch: Link Status — The current status of the link. Options ar e: ■ Ready — The port is ready to accept a link. ■ Active — The link is present at this port. T ransmit Packet Count (Tx Pkt Count) — The number of packets that have been successfully transmit[...]

9-6 C HAPTER 9: S TATUS M ONITORING AND S TATISTICS Port Err ors The Switch 3800 keeps track of errors for each port. T o view port error , type show port <portlist> errors The following port error information is collected by the Switch: Link Status — The current status of the link. Options ar e: ■ Ready — The port is ready to accept a [...]

Switch Logging 9-7 Receive Jabber Frames (RX Jab) — The total number of frames received by the port that wer e of longer than the support maximum length and had a Cyclic Redundancy Check (CRC) error . Receive Alignment Errors (RX Align) — The total number of frames received by the port that occurs if a frame has a CRC err or and does not contai[...]

9-8 C HAPTER 9: S TATUS M ONITORING AND S TATISTICS ■ Message — The message contains the log information with text that is specific to the problem. Local Logging The Switch maintains up to 1,000 messages in its internal log. Y ou can display a snapshot of the log at any given point in time by using the following command: show log {<priority[...]

Switch Logging 9-9 If priority is not specified, only messages of critical priority are displayed. If the subsystem is not specified, all subsystems are displayed. If you enable the log display on a terminal connected to the console port, your settings will remain in ef fect even after your console session is ended (unless you explicitly disable [...]

9-10 C HAPTER 9: S TATUS M ONITORING AND S TATISTICS Logging Commands The commands described in T able 9-4 allow you to do the following: ■ Configure logging options ■ Reset logging options ■ Display the log ■ Clear the log T able 9-4 Logging Commands Command Description config log display {<priority>} {<subsystem>} Allows you [...]

RMON 9-11 RMON Using the Remote Monitoring (RMON) capabilities of the Switch allows network administrators to make decisions about improving Switch efficiency and r educing the load on the network. The following sections explain more about RMON concepts and the RMON features supported by the Switch 3800. Y ou can only use the RMON features of the [...]

9-12 C HAPTER 9: S TATUS M ONITORING AND S TATISTICS A typical RMON setup consists of the following two components: ■ The RMON probe — An intelligent, r emotely controlled device or software agent that continually collects statistics about a LAN segment or VLAN. The probe transfers the information to a management workstation on request or when [...]

RMON 9-13 Alarms The Alarms group pr ovides a versatile, general mechanism for setting threshold and sampling intervals to generate events on any MIB variable. Alarms inform you of a network performance problem and they can trigger automated action responses thr ough the Events group. Events Effective use of the Events gr oup saves you time. Rather[...]

9-14 C HAPTER 9: S TATUS M ONITORING AND S TATISTICS An RMON probe, however , autonomously looks at the network on behalf of the management workstation without affecting the characteristics and performance of the network. The probe r eports by exception, which means that it only informs the management workstation when the network has entered an abn[...]

RMON 9-15 When using the RMON features of the Switch, you should note the following: ■ After the default sessions are cr eated, they have no special status. Y ou can delete or change them as required. ■ The greater the number of RMON sessions, the gr eater the burden on the management resour ces of the Switch. However , the forwarding performan[...]

9-16 C HAPTER 9: S TATUS M ONITORING AND S TATISTICS SW3800.BK Page 16 Tuesday, May 5, 1998 5:20 PM[...]

10 S OFTWARE U PGRADE AND B OOT O PTIONS This chapter describes the procedur e for upgrading the Switch software image. It also covers how to save and load a primary and secondary configuration file on the Switch. Upgrading the Softwar e The image file contains the executable code that runs on the Switch 3800. It comes preinstalled on the Switch[...]

10-2 C HAPTER 10: S OFTWARE U PGRADE AND B OOT O PTIONS Y ou can select which image the Switch will load on the next reboot by using the following command: use image {primary | secondary} If you do not specify which image to use, the Switch automatically loads the primary image. Rebooting the Switch T o reboot the Switch, use the following command:[...]

Boot Option Commands 10-3 Returning to Factory Defaults T o return the Switch configuration to factory defaults, use the following command: unconfig switch This command resets the entir e configuration, with the exception of user accounts and passwords that have been configur ed. T o reset all parameters, use the following command: unconfig swit[...]

10-4 C HAPTER 10: S OFTWARE U PGRADE AND B OOT O PTIONS SW3800.BK Page 4 Tuesday, May 5, 1998 5:20 PM[...]

A S AFETY I NFORMATION Y ou must read the following safety information before carrying out any installation or removal of components, or any maintenance pr ocedures on the Switch 3800. Important Safety Information WARNING: Warnings contain directions that you must follow for your personal safety . Follow all instructions carefully . Please read the[...]

A-2 A PPENDIX A: S AFETY I NFORMATION ■ This unit operates under SEL V (Safety Extra Low V oltage) conditions according to IEC 950. The conditions ar e only maintained if the equipment to which it is connected also operates under SEL V conditions. ■ The appliance coupler (the connector to the unit and not the wall plug) must have a configurati[...]

Important Safety Information A-3 ■ If the power cord plug is unsuitable and must be r eplaced, you may find other codings for the respective connections. Connect the power supply wires for the unit accor ding to the following scheme: ■ Brown wir e to the Live (Line) plug terminal which may be marked with the letter ‘L ’ or colored r ed. ?[...]

A-4 A PPENDIX A: S AFETY I NFORMATION Lithium Battery ■ Replace the lithium battery with the same or equivalent type, as recommended by the manufactur er . W ARNING: There is a danger of explosion if the battery is incorr ectly replaced. ■ Dispose of used batteries according to the manufactur ers instructions. ■ Do not disposed of the batteri[...]

L’information de Sécurité Importante A-5 ■ Pour réduire les risques d'incendie ou de choc électrique, installez ce groupe sous abri dans une zone dont la températur e et l'humidité sont régulées et qui ne contient pas de produits contaminateurs conductifs. Power ■ Pour garantir le respect des normes internationales de sécur[...]

A-6 A PPENDIX A: S AFETY I NFORMATION Cordon électrique ■ Il doit êtr e agréé dans le pays d'utilisation : ■ Si la prise mâle du cordon électrique est défectueuse, vous devez la remplacer en identifiant d'autr es codages pour assurer les différ entes connexions nécessaires. Branchez les fils d'alimentation électrique [...]

L’information de Sécurité Importante A-7 porte-fusibles. Pour ce groupe, vous devez uniquement utiliser des fusibles réalisés par le même constructeur et offrant le même pouvoir de coupure et r espectant le même type que le fusible d'origine. Refermez le porte-fusibles. ■ Pour respecter les normes eur opéennes de sécurité, il ne [...]

A-8 A PPENDIX A: S AFETY I NFORMATION ■ les batteries au lithium ne figurent pas sur la liste EP A des déchets dangereux. Par conséquent, vous pouvez en général vous en débarrasser comme s'il s'agissait d'un déchet normal. ■ si vous souhaitez vous débarrasser de quantités importantes, contactez un service local de gestio[...]

Wichtige Sicherheitsinformationen A-9 ■ Das Gerät muß an eine geerdete Steckdose angeschlossen wer den, die die europäischen Sicherheitsnormen erfüllt. ■ Das Gerät nicht an eine Wechselstr omsteckdose anschließen, die nicht geerdet ist. ■ Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die Stromversorgung de[...]

A-10 A PPENDIX A: S AFETY I NFORMATION ■ Zur Erfüllung europäischer Sicherheitsnormen darf keine Ersatzsicherung am Geräteeingang angebracht werden. Es dürfen nur Sicherungen vom gleichen Hersteller , der gleichen Marke und Art mit dem Gerät verwendet werden. Faseroptikanschlüsse - Optische Sicherheit ■ Niemals mit einem V ergrößerungsg[...]

Wichtige Sicherheitsinformationen A-11 Lithiumbatterie ■ Die Lithiumbatterie nach den Empfehlungen des Herstellers durch eine Batterie des gleichen oder eines gleichwertigen T yps ersetzen. W ARNHINWEIS: W ird die Batterie falsch ersetzt, besteht Explosionsgefahr . ■ V erbrauchte Batterien nach den Angaben des Herstellers entsorgen. ■ Batteri[...]

A-12 A PPENDIX A: S AFETY I NFORMATION SW3800.BK Page 12 Tuesday, May 5, 1998 5:20 PM[...]

B T ECHNICAL S PECIFICATIONS Physical Dimensions Height: 3.5 inches x Width: 17.32 inches x Depth: 17.32 inches Weight: 22 pounds Environmental Requir ements Operating Temperature 0 to 40˚ C Storage Temperature -10 to 70 ˚ C Operating Humidity 10% to 95% relative humidity, noncondensing Standards EN60068 (IEC68) Safety Agency Certifications IEC 9[...]

B-2 A PPENDIX B: T ECHNICAL S PECIFICATIONS Standards Supported Ether net ISO 8802-3 IEEE 802.3z/D3 ISO 10038:1993 (IEEE 802.1D) IEEE 802.1Q/D10 SNMP SNMP protocol (RFC 1157) MIB-II (RFC 1213) Bridge MIB (RFC 1493) VLAN MIB (RFC 1573) RMON MIB (RFC 1757) T erminal Emulation Telnet (RFC 854) Protocols Used for Administration UDP (RFC 768) IP (RFC 79[...]

C T ROUBLESHOOTING If you encounter problems when using the Switch, this Appendix may be helpful. If you have a problem which is not listed her e or in the release notes, please contact your local technical support r epresentative. LEDs Power LED does not light: Check that the power cable is firmly connected to the device and to the supply outlet.[...]

C-2 A PPENDIX C: T ROUBLESHOOTING Both sides of the link must have the same setting for autonegotiation. It the two are dif ferent, typically the side with autonegotiation disabled will have the link LED lit, and the side with autonegotiation enabled will not be lit. The default configuration for a port is autonegotiation enabled. This can be veri[...]

Using the Command-Line Interface C-3 T raps are not received by the SNMP Network Manager: Check that the SNMP Network Manager's IP address and community string are corr ectly configured and that the IP address of the T rap Receiver is configured pr operly on the Switch. The SNMP Network Manager or T elnet workstation can no longer access the[...]

C-4 A PPENDIX C: T ROUBLESHOOTING Y ou forget your password and cannot log on: If you are not an administrator , another user having administrator access level can log on, delete your user name, and create a new user name for you, with a new password. Alternatively , another user having administrator access level can log in and initialize the devic[...]

Using the Command-Line Interface C-5 VLAN Names: There ar e restrictions on VLAN names. They cannot contain white spaces and cannot start with a numeric value unless you use quotation marks around the name. If a name contains white spaces or starts with a numeric, you must use quotation marks whenever referring to the VLAN name. 802.1Q links do not[...]

C-6 A PPENDIX C: T ROUBLESHOOTING The Switch keeps aging out endstation entries in the Switch Forwarding Database (FDB): Reduce the number of topology changes by disabling STP on those Switches that do not use redundant paths. Specify that the endstation entries are static or permanent. Routing The Switch sees RIP updates but other routers don’ t[...]

D T ECHNICAL S UPPORT 3Com provides easy access to technical support information thr ough a variety of services. This appendix describes these services. Information contained in this appendix is correct at time of publication. For the very latest, we recommend that you access 3Com Corporation’ s World Wide Web site as described below . Online T e[...]

D-2 A PPENDIX D: T ECHNICAL S UPPORT Access by Digital Modem ISDN users can dial in to 3ComBBS using a digital modem for fast access up to 56 Kbps. T o access 3ComBBS using ISDN, use the following number: 408 654 2703 3ComFacts SM Automated Fax Service 3Com Corporation’ s interactive fax service, 3ComFacts, provides data sheets, technical article[...]

Support from Your Network Supplier D-3 3ComForum on CompuServe ® Online Service 3ComForum is a CompuServe-based service containing patches, software, drivers, and technical articles about all 3Com pr oducts, as well as a messaging section for peer support. T o use 3ComForum, you need a CompuServe account. T o use 3ComForum: 1 Log on to CompuServe.[...]

D-4 A PPENDIX D: T ECHNICAL S UPPORT Support fr om 3Com If you are unable to r eceive support from your network supplier , technical support contracts are available fr om 3Com. Contact your local 3Com sales office to find your authorized service provider using one of these numbers: Regional Sales Office Telephone Number Regional Sales Office Tele[...]

Returning Products for Repair D-5 Returning Products for Repair Before you send a pr oduct directly to 3Com for repair , you must first be obtain a Return Materials Authorization (RMA) number . Products sent to 3Com without RMA numbers will be returned to the sender unopened, at the sender’ s expense. T o obtain an RMA number , call or fax: Coun[...]

D-6 A PPENDIX D: T ECHNICAL S UPPORT SW3800.BK Page 6 Tuesday, May 5, 1998 5:20 PM[...]

G LOSSARY ageing The automatic removal of dynamic entries fr om the Switch Database that have timed-out and are no longer valid. ARP Address Resolution Pr otocol. The protocol used to dynamically bind high-level IP addresses to low-level har dware addresses. ARP is used only across a single physical network and is limited to networks that support h[...]

2 G LOSSARY CSMA/CD Carrier Sense Multiple Access/Collision Detection that is a channel access method used by Ethernet and IEEE 802.3 standards in which devices transmit only after finding the data channel clear for some period of time. When two devices transmit simultaneously , a collision occurs and the colliding devices delay their retransmissi[...]

3 LAN Local Area Network that consists of connected computing r esources (such as PCs, printers, and servers) covering a relatively small geographic area (usually not larger than a floor or building). Characterized by high data rates and low error rates. latency The delay between the time a device receives a frame and the time the frame is forward[...]

4 G LOSSARY on a wide range of computers and networking equipment and may be used to manage many aspects of network and endstation operation. Spanning T ree Protocol (STP) A bridge-based mechanism for pr oviding fault tolerance on networks. STP works by allowing the implementation of parallel paths for network traffic, and ensuring that r edundant[...]

I NDEX 1 I NDEX Numerics 3Com Bulletin Board Service (3ComBBS) D-1 3Com sales offices D-4 3Com URL D-1 3ComFacts D-2 3ComForum D-3 A accounts, creating 3-3 alarms 9-15 Alarms (RMON group) 9-13 , 9-14 B BOOTP 3-5 Bridge Identifier 7-3 bridge priority , configuring 4-14 , 7-11 bulletin board service D-1 C Commands 4-5 , 4-6 common 4-5 history 4-5 [...]

2 I NDEX router interfaces 8-1 router show commands (table) 8-12 routing table configuration commands (table) 8-7 dynamic routes 8-3 populating 8-2 static routes 8-3 settings, displaying 8-12 L LEDs 1-8 load sharing 3-15 configuring 3-15 log display 9-8 logging and T elnet 9-9 commands 9-10 fault level 9-7 local 9-8 real-time display 9-8 remote 9[...]

I NDEX 3 forward delay 4-14 , 7-11 Hello Time configuring 4-14 , 7-11 description 7-4 Max Age configuring 4-14 , 7-11 overview 7-1 path costs 4-15 , 7-11 port priority 4-15 , 7-11 Switch 3800 configuration examples 1-5 dimensions B-1 factory defaults 1-10 free-standing installation 2-3 front view 1-7 Gigabit Ethernet ports 1-7 installing 2-2 LED[...]

4 I NDEX SW3800.BK Page 4 Tuesday, May 5, 1998 5:20 PM[...]

3Com Corporation L IMITED W ARRANTY H ARDWARE 3Com warrants its hardware products to be free from defects in workmanship and materials, under normal use and service, for the following lengths of time from the date of purchase from 3Com or its Authorized Reseller: If a product does not operate as warranted above during the applicable warranty period[...]

3COM SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY [...]