ZyXEL Communications IES-1000 инструкция обслуживания

IES-1000 Integrated Ethernet Switch Version 2.05 11/2005 User’s Guide[...]

IES-1000 User ’s Guide ii Copyright Copyright Copyright © 2005 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in an y form or by any means, electronic, mechanical, magnetic, optical, chem[...]

IES-1000 User ’s Guide Interference S tatement s and W arnings iii Interference S t atement s and W arnings FCC Interference Statement: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference receive d[...]

IES-1000 User ’s Guide iv W arranty ZyXEL Limited W arranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due[...]

IES-1000 User ’s Guide Customer Support v Customer Support Please have the following information read y when you contact customer support.  Product model and serial number.  Warranty information.  Date that you received your device.  Brief description of the problem and the steps you took to solve it. Support e-mail Telephone Web Site[...]

IES-1000 User ’s Guide vi W arranty support@zyxel.es +34-902-195-4 20 Spain sales@zyxel.es +34-913-005-345 www.zyxel.es ZyXEL Communications Alejandro Villegas 33 1º, 28043 Madrid Spain support@zyxel.se +46-31-744-7700 Sweden sales@zyxel.se +46-31-744-7701 www.zyxel.se ZyXEL Communications A/S Sjöporten 4, 41764 Göteborg Sweden support@ua.zyxe[...]

IES-1000 User ’s Guide T able of Contents vii T able of Content s Copyri ght ...................................................................................................................... ............................................. ii Interference S tatem ents and W arnings ...............................................................[...]

IES-1000 User ’s Guide viii T able of Contents 5.1 Removing a G.SHDSL SAM1008 Network Module ............................................................................ 5-1 5.2 Installing a Network Module .................................................................................................... ............. 5-2 Hardware Connections an[...]

IES-1000 User ’s Guide T able of Contents ix 10.3 Bridge Overview ................................................................................................................ ................. 10-2 10.4 Bridge Setup Screen ............................................................................................................ ............[...]

IES-1000 User ’s Guide x T able of Contents Chapter 15 VLAN........................................................................................................................... ................. 15-1 15.1 VLAN Over view .................................................................................................................. .......[...]

IES-1000 User ’s Guide T able of Contents xi 21.6 Configured Settings ............................................................................................................ ................. 21-2 21.7 Password ....................................................................................................................... ............[...]

IES-1000 User ’s Guide xii T able of Contents 27.2 Ethernet Commands .............................................................................................................. .............. 27-1 Chapter 28 Bridge Co mmands ................................................................................................................ .......[...]

IES-1000 User ’s Guide T able of Contents xiii 35.1 Configuration Files of the Network Module ...................................................................................... . 35-1 35.2 Configuration Backup ........................................................................................................... .............. 35-1 35.3 C[...]

IES-1000 User ’s Guide xiv List of Figures List of Figures Figure 1-1 MTU Application ..................................................................................................... .................................. 1-5 Figure 1-2 Central Office or ISP Application ............................................................................[...]

IES-1000 User ’s Guide List of Figures xv Figure 9-2 Ho me Screen ......................................................................................................... .................................. 9-2 Figure 9-3 Bridge Setup Example ................................................................................................ ........[...]

IES-1000 User ’s Guide xvi List of Figures Figure 12-3 G .SHDS L Profile Setup .............................................................................................. .......................... 12-6 Figure 12-4 G .S HDSL Add Profile ................................................................................................ ...........[...]

IES-1000 User ’s Guide List of Figures xvii Figure 20-3 Reboot Sy stem Conf irmation ......................................................................................... ...................... 20-6 Figure 20-4 Logout ............................................................................................................. ................[...]

IES-1000 User ’s Guide xviii List of Figures Figure 33-1 Setting IP Addr ess and Defaul t Gateway ............................................................................. ................ 33-2 Figure 36-1 BOOT P/TFTP Server .................................................................................................. ....................[...]

IES-1000 User ’s Guide List of T able s xix List of T ables T able 3-1 Front Panel Ports of the SAM1008 Ne twork Module ...................................................................... .......... 3-2 T able 3-2 Front Panel Ports of the AAM1008 Ne twork Module ...................................................................... ...........[...]

IES-1000 User ’s Guide xx List of T able s T able 10-18 Bridge Fast Mode VLAN ID Setup ..................................................................................... ................ 10-21 T able 10-19 IP Setup ........................................................................................................... ......................[...]

IES-1000 User ’s Guide List of T able s xxi T able 19-2 Hard ware Monitor .................................................................................................... .............................. 19-2 T able 19-3 Port S tatistics ..................................................................................................... ......[...]

IES-1000 User ’s Guide xxii Preface Preface Congratulations on your purchase of the IES-1000 Integrated Ethernet Switch. About this User ’ s Manual This user’s guide explains how to:  Install the IES-1000 chassis  Install network modules into the chassis  Use the web configurator or command line interface to manage and troubleshoot t[...]

IES-1000 User ’s Guide Preface xxiii Please refer to www.zy xel.com for an online glossary of networking terms or the ZyXEL download library for additional support documentation. Online Registration Register your product online at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. General Synt ax Conventions ?[...]

Overview and Installation I Part I: Overview and Installation This part introduces the general features, defaul t settings, hardware and installation of the IES- 1000 Integrated Ethernet Switch.[...]

[...]

IES-1000 User ’s Guide Getting to Know the IES-1000 1-1 Chapter 1 Getting to Know the IES-1000 This chapter describes the key features, benefits and applica tions of your IES-1000. The IES-1000 (Integrated Ethernet Switch) is an IP-based DSLAM (Internet Protocol Digital Subscriber Line Access Multiplexer) that connects up G.SHDSL or ADSL sub scri[...]

IES-1000 User ’s Guide 1-2 Getting to Know the IES-1000  G.lite (ITU-T G.992.2)  G.hs (ITU-T G.994.1)  ANSI T1.413 issue 2  ETSI (TS 101 388) • Rate adaptation support N-wire Mode (SAM1008) The n-wire mode allows you to physically bundle two or four G.SH DSL ports into a single 4-wire or 8-wire G.SHDSL connection. 1 This can increas[...]

IES-1000 User ’s Guide Getting to Know the IES-1000 1-3 You can limit the number of MAC addresses that may be dy namically learned or statically configured on a port. You may enable/disable the MAC count filter on individual ports. IEEE 802.1X Port-based Authentication The IES-1000 supports the IEEE 802.1X st andard for centralized user authen ti[...]

IES-1000 User ’s Guide 1-4 Getting to Know the IES-1000 Overheating Detection, W arning and Safegaurd An ALM LED turns on when the IES-1000’s internal temper ature is too high and turns off when the tem perature has returned to a normal level. Internal fans cool the unit. Comp act Design for Limited S p ace The IES-1000 occupies only 1 U of sta[...]

IES-1000 User ’s Guide Getting to Know the IES-1000 1-5 Figure 1-1 MTU Application[...]

IES-1000 User ’s Guide 1-6 Getting to Know the IES-1000 1.2.2 Central Of fice or ISP Application The IES-1000 provides DSL service over telephone wires to subscribers. The following figure shows the IES- 1000 set up in an Internet Service Provider (ISP) building or teleph one company central office. Figure 1-2 Central Office or ISP Application[...]

IES-1000 User ’s Guide Factory Default Settings 2-1 This section describes the factory default settin gs of the IES-1000. 2.1 IP Parameters • IP address = 192.168.1.1 • Subnet mask = 255.255.255.0 • Default gateway = 192.168.1.254 2.2 Console Port • Baud rate = 9600 bps • Data bits = 8 • Parity = none • Stop bit = 1 • Flow control[...]

IES-1000 User ’s Guide 2-2 Factory Default Settings • Enable/Disable State: Disabled • Profile: DEFVAL  Maximum upstream/downstream speed: 2304 Kbps  Minimum upstream/downstream speed: 192 Kbps 2.6 ADSL Ports (AAM1008) • Encapsulation: RFC 1483 • Multiplexing: LLC-based • VPI: 0 • VCI: 33 • Enable/Disable State: Disabled • O[...]

IES-1000 User ’s Guide Factory Default Settings 2-3[...]

[...]

IES-1000 User ’s Guide Hardware Overview 3-1 This chapter gives a brief introductio n to the IES-1000 hardware. 3.1 Additional Inst allation Requirements A computer with Ethernet 10Base-T or 100Base-TX NIC (Network Interface Card) • WAN service provided by a local phone company A computer with terminal emulation softwa re configured to the foll[...]

IES-1000 User ’s Guide 3-2 Hardware Overview 3.3.1 Network Module Front Panel LEDs See the Turning On the IES-1000 chapter for details on the LED indicators on t he front panel of a SAM1008 or AAM1008 network module. 3.3.2 Front Panel Port s The following tables describe front panel ports. Table 3-1 Front Panel Ports of the SAM1008 Network Module[...]

IES-1000 User ’s Guide Hardware Installation 4-1 This chapter shows you how to install hardware for a freestanding or rack-m ounted scenario. 4.1 Environment The following are the recommended environments for the IES-1000. 4.1.1 Operating Environment Temperature: 0 — 50°C; Humidity: 5% — 95% (non-condensing) 4.1.2 S torage Environment Temper[...]

IES-1000 User ’s Guide 4-2 Hardware Installation 4.4.1 Att aching the Mounting Bracket s to the IES-1000 Step 1. Position a mounting bracket on one side of the IES-1000, lining up the four screw holes on the bracket with the screw holes on the side of the unit (see the figure shown next). Failure to use the proper screws may damage the unit. Figu[...]

IES-1000 User ’s Guide Hardware Installation 4-3 Figure 4-2 Mounting the IES-1000 on a Rack Step 2. Using a #2 Philips screwdriver, install the M5 flat head screws through the mounting bracket holes into the rack. Step 3. Repeat Step 1 and Step 2 to attach the second mounting bracket on t he other side of the rack.[...]

[...]

IES-1000 User ’s Guide Removing and Installing Network Modules 5-1 This chapter shows you how to remove and install network modules. Each IES-1000 accommodates up to two network modules. Remove and install modules via the front of the IES- 1000. The figure below shows the front view of a SA M1008 network m odule; the procedures for removing and i[...]

IES-1000 User ’s Guide 5-2 Removing and Installing Network Modules Figure 5-3 Removing a Network Module from the IES-1000 Chassis 5.2 Inst alling a Network Module Step 1. Hold the module with the network ports facing you an d insert it into an empty slot located on the front of the IES-1000 as shown next. Step 2. Push the bottom of the front of t[...]

IES-1000 User ’s Guide Removing and Installing Network Modules 5-3 Figure 5-4 Installing a Network Module into the IES-1000 Chassis The front of the network module must be flush with the front of the IES-1000 after you install a network module or it will not work! Step 3. Secure the module to the chassis by turning the tw o screws on the front of[...]

Hardware Connections II Part II: Hardware Connections and Troubleshooting This part covers how to connect the IES-1000 and tu rn it on. It also cove rs how to troubleshoot the hardware.[...]

IES-1000 User ’s Guide Hardware Connections 6-1 This chapter shows you how and where to make hardware connections. Before you make your hardware connections, make su re that your IES-1000 is safely and securely positioned. 6.1 Front Panel Connections All connections are made on the front panel of th e IES-1000. The following figur e shows the fro[...]

IES-1000 User ’s Guide 6-2 Hardware Connections Figure 6-2 Console Port Connection 6.3 SHDSL Port Connections The SHDSL ports connect to an MDF (Main Distribution Frame) and end-user equipment via telephone wires. • For detailed specifications about the associated RJ-11 connector, refer to the Pin Assignment appendix. • For more detail about [...]

IES-1000 User ’s Guide Hardware Connections 6-3 Figure 6-3 SHDSL Port and MDF Connections Step 3. Connect a different telephone wire to the lowe r port of the MDF using a punch-down tool. Step 4. Connect the other (RJ-11) end of the telephone wire to the end-user G.SHDSL modem/router. When you finish this procedure your connections should look si[...]

IES-1000 User ’s Guide 6-4 Hardware Connections Figure 6-4 SHDSL Port, MDF and User Equipment Connections Notes About MDFs (Main Distribution Frames) An MDF is usually installed between end-users’ equipment and the telephone company (CO) in a basement or telephone room. The MDF is the point of termination for the outside telephone co mpany line[...]

IES-1000 User ’s Guide Hardware Connections 6-5 Figure 6-5 Magnified View of MDF Wiring Connect wiring from end-user equipment to the lower por ts of an MDF using a telephone wire. Connect wiring from the telephone company to the upper ports of an MDF (see the previous figure). Some MDFs have surge protection circuitry built in be tween the two b[...]

IES-1000 User ’s Guide 6-6 Hardware Connections Figure 6-6 AAM1008 Installation Overview You can also use RJ-11 connectors on both ends of the telephone cables connect directly to an ADSL modem(s) or patch panel. This chapter discusses connections using MDFs. 6.4.1 T ypical Scenarios Your existing telephone wiring usually depends on yo ur region.[...]

IES-1000 User ’s Guide Hardware Connections 6-7 Figure 6-7 Installation Scenario A Procedure T o Connect T o An MDF Step 1. Connect the RJ-11 connector end of a telephone wire to one of the USER ports on the AAM1008. Step 2. Connect the other end of the telephone wire to th e upper ports of the MDF using a punch-down tool. Step 3. Connect the tel[...]

IES-1000 User ’s Guide 6-8 Hardware Connections Figure 6-8 One MDF for End-user and CO Connections Please refer to the following figure for the connection schema.  MDF 1 is the original MDF used for telephone connections only.  MDF 2 is used for telephone connections only.  MDF 3 is for ADSL service connections. Change the wiring (in the[...]

IES-1000 User ’s Guide Hardware Connections 6-9 Figure 6-9 Installation Scenario B Procedure T o Connect T o MDFs Step 1. Acquire two additional MDFs (MDFs 2 and 3). Step 2. Connect the RJ-11 connector ends of telephone wires you want for ADSL service to the USER ports on the AAM1008. Step 3. Connect the other ends of the telephone wires to the u[...]

IES-1000 User ’s Guide 6-10 Hardware Connections 6.4.4 Inst allation Scenario C Phone service is also available but there are two MDFs; one for end-user telephone lin e connections and the other one for CO telephone line connections (see the following figure). Users A and B have telephone (only) service. Figure 6-10 Two Separate MDFs for End-user[...]

IES-1000 User ’s Guide Hardware Connections 6-1 1 Figure 6-11 Installation Scenario C Procedure T o Connect T o MDFs Step 1. Acquire two additional MDFs (3 and 4). Step 2. Connect the RJ-11 connector ends of telephone wires you want for ADSL service to the USER ports on the AAM1008. Step 3. Connect the other ends of the telephone wires to the upp[...]

IES-1000 User ’s Guide 6-12 Hardware Connections Connect the top ports of MDF 1 to the telephone company. 6.4.5 LAN Port (Ethernet) Connection Connect the LAN port of your SAM1008 to an Ethernet WAN switch using a st raight-through Category 5 UTP (Unshielded Twisted Pair) cable with RJ -45 connectors. Connect the other end of the cable to an Ethe[...]

IES-1000 User ’s Guide Hardware Connections 6-13 Figure 6-13 Connecting the Power Cord to the IES-1000 and a Power Source 6.6 DC Power Model Power Connections Use the following procedures to connect the IES-1000 to a power source after you have installed the IES-1000 in a rack. Refer to power supply requirements in the hardware specifications in [...]

IES-1000 User ’s Guide 6-14 Hardware Connections Figure 6-14 Connecting IES-1000 Power[...]

IES-1000 User ’s Guide T urning On the IES-1000 7-1 Chapter 7 Tu r n i n g On the IES-1000 This chapter discusses the fans and LEDs of the IES-1000 after you turn it on. 7.1 Introduction Before turning on your IES-1000, m ake sure you: • Have attached a computer to the IES-1000 serial port as explained previously. • Can see the status LEDs on[...]

IES-1000 User ’s Guide 7-2 T urning On the IES-1000 Figure 7-2 SAM1008 Front Panel LEDs Figure 7-3 AAM1008 Front Panel LEDs Table 7-1 Network Module LED Descriptions LED COLOR STATUS DESCRIPTION ALM Red On The module has overheated. Off The module is functio ning within normal temperature para meters. SYS Green Blinking The system is initializing[...]

IES-1000 User ’s Guide Hardware T roubleshooting 8-1 This chapter explains how to troubleshoot IES-1000 hardware. 8.1 System S tartup When you turn on the IES-1000, it automatically runs a self-test that takes approximately 20 seconds. The SYS LED will remain on if your IES-1000 has started normally. 8.1.1 The SYS LED Does Not T urn On Table 8-1 [...]

IES-1000 User ’s Guide 8-2 Hardware T roubleshooting 8.3 The SHDSL LED(s) Do Not T urn On The SHDSL LEDs show the operational status of SHDSL port co nnections. If the SHDSL LED is off, it means the link to the SHDSL modem/router is down or there is not a connection to the SHDSL po rt. Table 8-3 SHDSL LED Troubleshooting STEP CORRECTIVE ACTION 1 [...]

IES-1000 User ’s Guide Hardware T roubleshooting 8-3 Table 8-4 ADSL LED Troubleshooting STEP CORRECTIVE ACTION 10 Repeat the steps above us ing a different ADSL port. 8.5 The LAN LED(s) Do Not T urn On Table 8-5 LAN LED Troubleshooting STEP CORRECTIVE ACTION 1 Make sure the LAN port of your network modul e is conne cted to an Ethernet WAN switch [...]

IES-1000 User ’s Guide 8-4 Hardware T roubleshooting tests to be done. Suppose you’re using installation scenar io “B” as shown in the chapter on MDF connections. The logic for other scenarios should be similar. Use steps A-D if there is no voice but you can transmit da ta. Use all of the steps if there is no voice and you cannot transmit d[...]

IES-1000 User ’s Guide Hardware T roubleshooting 8-5 Table 8-7 Testing In-house Wiring STEP TEST C Disconnect the telephone wire from CO . Conne ct a telephone to the telephone wire. If there is no dial tone, then the probl em is between your devi ce and MDF 2. Check the telephone wire’ s pin assignments (refer to the appendi ces for the proper[...]

Getting S tarted III Part III: Getting Started This part tells how to access and navigate the w eb configurator . It also describes the Getting S tarted web configurator screens.[...]

[...]

IES-1000 User ’s Guide Web Configurator Access and Navigation 9-1 This chapter describes how to log into the web configurator and navigate through it. 9.1 W eb Configurator Overview The embedded web configurator allows you to m anage the switch from anywhere on the network through a browser such as Microsoft Internet Explorer or Netsca pe Navigat[...]

IES-1000 User ’s Guide 9-2 W eb Configurator Access and Navigation 9.3 Home Screen This is the web configurator home screen. Click a link on t he navigation panel to go to the corresponding s creen. Figure 9-2 Home Screen Table 9-1 Navigation Panel Links LABEL DESCRIPTION Getting Started General Setup This link takes you to a screen w here you ca[...]

IES-1000 User ’s Guide Web Configurator Access and Navigation 9-3 Table 9-1 Navigation Panel Links LABEL DESCRIPTION Diagnostic This link takes you to a screen wher e you can view error logs and test the DSL connectio ns. Config Save Click this link to save your changes to the device’ s non-volatile memory. Logout Use this to exit the web confi[...]

IES-1000 User ’s Guide 9-4 W eb Configurator Access and Navigation 9.5 Saving Y our Configuration Click Apply in a configuration screen to save your changes back to the IES-1000’s volatile memory. The IES- 1000 loses these changes if it is turned off or loses power. Click Config Save on the navigation panel to the left to save your changes to t[...]

IES-1000 User ’s Guide Web Configurator Access and Navigation 9-5 Click the Packet Type Filter to go down one level to the Packet Type Filter Setup screen (shown next). Figure 9-4 Bridge Packet Type Filter Setup Example Click the link labeled Bridge Setup in the Packet Type Filter Setup screen to go back up a level and view the Bridge Setup scree[...]

[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-1 This chapter explains the General Setup and Bridge Setup screens. 10.1 Getting S tarted Overview The web configurator allows you to configure basic settings using the Getting Started screens. 10.2 General Setup Screen Click General Setup in the navigation panel to open t his screen. Use this sc[...]

IES-1000 User ’s Guide 10-2 Getting S tarted Screens Table 10-1 General Setup LABEL DESCRIPTION Slot ID Type 1 or 2 for the slot ID number. The sl ot ID help s keep track of this individual network module. Apply Click Apply to save your changes back to the IES-1000's volatile memory. The IES-1000 loses these changes if it is turned off or lo[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-3 Figure 10-2 Bridge Setup The following table describes this screen. Table 10-2 Bridge Setup LABEL DESCRIPTION Operating Mode Bridge Mode Choose Normal or Fast from the drop-down list box. The Normal mode supports 802.1Q tagged VLAN (enabled in VLAN Set up), which allows tagge d/untagged frames [...]

IES-1000 User ’s Guide 10-4 Getting S tarted Screens Table 10-2 Bridge Setup LABEL DESCRIPTION MAC Count Filter Click this link to go to a scr een for setting limits on how many MAC addres ses may be dynamically learned or stat ically configured on a port. MAC Address Record Click this link to show the filtering database for e ach port. IGMP Snoo[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-5 Table 10-3 Bridge Packet Type Filter Setup LABEL DESCRIPTION Packet Filter Type Choose Any or IP or PPPoE from the drop-do wn list. Choose Any to allow all kinds of packets, IP to allow IP packets only or PPPoE to allow PPPoE packe ts only. Apply Click Apply to save your changes back to the IES[...]

IES-1000 User ’s Guide 10-6 Getting S tarted Screens Figure 10-4 Default Port Filter Settings 10.5.1 Port Filter Setup Screen Click Port Filter in the Bridge Setup screen to open this screen. Figure 10-5 Bridge Port Filter Setup The following table describes this screen. Table 10-4 Bridge Port Filter Setup LABEL DESCRIPTION Bridge Setup Click thi[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-7 Figure 10-6 Edit Bridge Port Filter Setup The following table describes this screen. Table 10-5 Edit Bridge Port Filter Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Bridge Port Filter Setup Click this link to go to the Bridge Port Filter Setup screen. A[...]

IES-1000 User ’s Guide 10-8 Getting S tarted Screens Figure 10-7 Bridge MAC Filter Setup The following table describes this screen. Table 10-6 Bridge MAC Filter Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Port Number Click the port name to edit that port’s MAC filter setup. Filtering Enabled? This fiel[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-9 Table 10-7 Bridge MAC Filter Entry List LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Bridge MAC Filter Setup Click this link to go to the Bridge MAC Filter Setup screen. Filtering Enable Select this check box to enable MAC filtering on this port. Apply Click [...]

IES-1000 User ’s Guide 10-10 Getting S tarted Screens Table 10-8 Bridge MAC Filter Entry Add LABEL DESCRIPTION Apply Click Apply to save your changes back to the IES-1000's volatile memory. The IES-1000 loses these changes if it is turned off or lose s power, so use the Config Save link on the navigation panel to the left to save your cha ng[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-1 1 Table 10-9 MAC Count Filter Setup LABEL DESCRIPTION Max Static MAC Count This field’s first number displays how ma ny MA C addresses are statically spe cified for a port. This field’s second number displays the limit of how many MAC addresses may be statically specified on the port. 10.5.[...]

IES-1000 User ’s Guide 10-12 Getting S tarted Screens Table 10-10 MAC Count Filter Edit LABEL DESCRIPTION Max Static MAC Count Use this field to limit the number of MAC addresses that may be statically specifi ed for this port. For example, if you are configuring port 2 and y ou set this field to "5", then only five device MAC addresses[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-13 The following table describes this screen. Table 10-11 Bridge MAC Address Record LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Setup Aging Time Enter a time from 10 to 1,000,000 seconds. Thi s is how long all dynamically learned MAC addresses remain in the MA[...]

IES-1000 User ’s Guide 10-14 Getting S tarted Screens Figure 10-13 Bridge IGMP Snooping Record The following table describes this screen. Table 10-12 Bridge IGMP Snooping Record LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. IGMP Snooping Timeout Specify how long the IES-1000 is to retain entries in the group mem[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-15 Table 10-12 Bridge IGMP Snooping Record LABEL DESCRIPTION Member Ports This field di splays the ports that bel ong to this multicast grou p, E=Et hernet, 1~8 = ADSL ports 1 through 8. Refresh Click this button to update the multicast filtering record. FlushAll Click this button to clear the mu[...]

IES-1000 User ’s Guide 10-16 Getting S tarted Screens 10.5.11 DHCP Relay Screen Click DHCP Relay in the Bridge Setup screen to open this screen. Figure 10-15 DHCP Relay Setup Table 10-13 DHCP Relay Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. DHCP Relay Enable Enable DHCP relay to have the Integrated Ethe[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-17 Figure 10-16 Add DHCP Server Table 10-14 Add DHCP Server LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. DHCP Relay Setup Click this link to go to the DHCP Relay Setup scree n. IP Address Type the IP address of the DHCP server to which the Integrated Et hernet [...]

IES-1000 User ’s Guide 10-18 Getting S tarted Screens the memory capacity of the device. In essence, RADIUS authentication allows you to validate an unlimited number of users from a central location. Figure 10-17 RADIUS Server 10.5.13 802.1X Setup Sc reen Click 802.1X in the Bridge Setup screen to open this screen. Figure 10-18 802.1X Setup Table[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-19 Table 10-15 802.1X Setup LABEL DESCRIPTION Control When this field displays Auto , the IES-1000 authenticates all subscribers before they can access the network through this port. When this field displays Force Authorized , all connected users a re allowed to access the network through this po[...]

IES-1000 User ’s Guide 10-20 Getting S tarted Screens Table 10-16 RADIUS Server Setup LABEL DESCRIPTION Shared Secret Specify a password (up to 31 alphanumer ic cha racters) as the key to be shared between the external RADIUS server and the IES-1000. This key is not sent over the network. This key must be the same on the external RADIUS server an[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-21 Table 10-17 Edit 802.1x Setup LABEL DESCRIPTION Reauthentication Select ( On ) if a subscriber has to periodi cally re-enter his or her usernam e and password to stay connected to the port. Reauthentication Timer Specify how often (60~65535 seconds) a sub scriber has to re-enter his or her use[...]

IES-1000 User ’s Guide 10-22 Getting S tarted Screens Table 10-18 Bridge Fast Mode VLAN ID Setup LABEL DESCRIPTION Port Number This is the port's name. VLAN ID Enter a VLAN ID number for the port. The valid range is 1-4094. You can not configure more than one port to use the same VLAN ID. Apply Click Apply to save your changes back to the IE[...]

IES-1000 User ’s Guide Getting S tarted Screens 10-23 Table 10-19 IP Setup LABEL DESCRIPTION Default Gateway Enter the IP address of the default-outgoing gatew ay in dotted de cimal notation, for example 192.168.1.254. Apply Click Apply to save your changes back to the I ES-1000's volatile memory. The IES-1000 loses these changes if it is tu[...]

[...]

IES-1000 User ’s Guide ADSL Module Port Setup 11 - 1 This chapter explains how to configure individual ports on the AAM-1008. 11.1 ADSL Module Port Setup Overview The web configurator allows you to configure settings for the ADSL Access Module’s ports. 11.2 ADSL S tandards Overview The ADSL module supports both the G.lite and the G.dmt sta ndar[...]

IES-1000 User ’s Guide 11 - 2 ADSL Module Port Setup 11.5 Interleave Delay Interleave delay is the wait (in milliseconds) that determines the size of a single block of data to be interleaved (assembled) and then transmitted. Inte rleave delay is used when transmissi on error correction (Reed- Solomon) is necessary due to a less than ideal telepho[...]

IES-1000 User ’s Guide ADSL Module Port Setup 11 - 3 - Maximum Signal/Noise Ratio: 31 db - Minimum Signal/Noise Ratio: 0 db - Minimum Transmission Rate: 32 Kbps - Maximum Transmission Rate: 2048 Kb ps Upstream ADSL settings: - Latency Delay: 4ms - Target Signal/Noise Ratio: 6 db - Maximum Signal/Noise Ratio: 31 db - Minimum Signal/Noise Ratio: 0 [...]

IES-1000 User ’s Guide 11 - 4 ADSL Module Port Setup Figure 11-1 ADSL Port Setup The following table describes this screen. Table 11-2 ADSL Port Setup LABEL DESCRIPTION Profile Setup Click this link to go to a screen for setting up DSL pro files. Port Number This field shows “0” for the Ethernet port. Active This field shows whether or not th[...]

IES-1000 User ’s Guide ADSL Module Port Setup 11 - 5 11.8.1 ADSL Profile Setup Screen A profile is a list of settings that you define. Then you can assign them to one or more individual ports. Click the Profile Setup link in the Port Setup screen to go to the Profile Setup screen. Figure 11-2 ADSL Profile Setup Table 11-3 ADSL Profile Setup LABEL[...]

IES-1000 User ’s Guide 11 - 6 ADSL Module Port Setup ADSL Profile Add or Edit Screen Click the Profile Setup link in the Port Setup screen to go to the Profile Setup screen. Click the Add button in the Profile Setup screen to add a new profile or click the name of an existing profile to edit the profile. Figure 11-3 ADSL Add Profile Table 11-4 AD[...]

IES-1000 User ’s Guide ADSL Module Port Setup 11 - 7 Table 11-4 ADSL Add Profile LABEL DESCRIPTION Min Rate (Kbps) Type the minimum upstream transfer rate (from 3 2 to 1024 Kbps) for this profile. Configu re the minimum upstream transfer rate to be less than the m aximum upstream transfer rate. Latency Delay(ms) Configure this field when you set [...]

IES-1000 User ’s Guide 11 - 8 ADSL Module Port Setup When auto-negotiation is turned on, the Ethernet port of the IES-1000 negotiates with the peer Ethernet port on the Ethernet cable automatically to determine the optimal connection speed and duplex m ode. If the peer Ethernet port does not support auto-negotiation or turns off this feature, the[...]

IES-1000 User ’s Guide ADSL Module Port Setup 11 - 9 Table 11-5 Ethernet Port Setup LABEL DESCRIPTION Default VLAN ID Type the Port VLAN ID (PVID) from 1 to 4094. The IES-1000 assig ns the PVID to untagged frames or priority frames (0 VID) received on this port. GVRP GVRP (GARP VLAN Registration P rotocol) is a registration protocol that defines [...]

IES-1000 User ’s Guide 1 1-10 ADSL Module Port Setup Figure 11-5 ADSL Port Setup Edit The following table describes this screen. Table 11-6 ADSL Port Setup Edit LABEL DESCRIPTION Channel Setup Click this link to go to the port's Channel Setup screen. Port Setup Click this link to go to the Port Setup screen. Name Type a descri ptive name to [...]

IES-1000 User ’s Guide ADSL Module Port Setup 11 - 11 Table 11-6 ADSL Port Setup Edit LABEL DESCRIPTION Default VLAN ID Type the Port VLAN ID (PVID) from 1 to 4094. The IES-1000 assig ns the PVID to untagged frames or priority frames (0 VID) received on this port. GVRP GVRP (GARP VLAN Registration P rotocol) is a registration protocol that define[...]

[...]

IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-1 This chapter explains how to configure individual ports on the SAM1008. 12.1 G . SHDSL Module Port Setup Overview The web configurator allows you to configure settings for the G.SHDSL Access Module’s ports. 12.2 G . SHDSL S tandards Overview The G.SHDSL module supports both the Annex A and [...]

IES-1000 User ’s Guide 12-2 G .SHDSL Module Port Setup You can n-wire bundle multiple groups of ports on a single IES-1000 (or even within a single SAM1008 m odule) as long as they do not overlap. 12.5 Port Bonding The port bonding feature allows you to send IP packets over two to eight G.SHDSL connections as a single connection. Since n-wire mod[...]

IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-3 12.7 Default G .SHDSL Module Settings The default profile always exists and all of the G.SHD SL ports use the default profile settings when the network module is shipped. The default profile' s name is set to DEFVAL . The default profile can’t be dele ted. 12.7.1 Default G .SHDSL Modul[...]

IES-1000 User ’s Guide 12-4 G .SHDSL Module Port Setup Figure 12-2 G.SHDSL Port Setup The following table describes this screen. Table 12-2 G.SHDSL Port Setup LABEL DESCRIPTION Profile Setup Click this link to go to a screen for setting up DSL pro files. Port Number This field shows “0” for the Ethernet port. Active This field shows whether o[...]

IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-5 Table 12-2 G.SHDSL Port Setup LABEL DESCRIPTION Active This field shows whether the port is turned on ( Yes ) or not ( No ). The factory default of all DSL ports is disabled. A port must be enabled for data transmission to occur. Name This field shows the name that identifies this port. Profi[...]

IES-1000 User ’s Guide 12-6 G .SHDSL Module Port Setup Click the Profile Setup link in the Port Setup screen to go to the Profile Setup screen. Figure 12-3 G.SHDSL Profile Setup Table 12-3 G.SHDSL Profile Setup LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen. Profile Name These are the names of individual profiles. The[...]

IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-7 Figure 12-4 G.SHDSL Add Profile Table 12-4 G.SHDSL Add Profile LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen. Profile Name When editing a profile, this is the name of this profile. When adding a profile, type a name for the profile. PSD Region Select the Power Sp[...]

IES-1000 User ’s Guide 12-8 G .SHDSL Module Port Setup Figure 12-5 G.SHDSL Port Setup The following table describes this screen. Table 12-5 G.SHDSL Port Setup LABEL DESCRIPTION Channel Setup Click this link to go to the port's Channel Setup screen. Port Setup Click this link to go to the Port Setup screen. Name Type a name to identify this p[...]

IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-9 Table 12-5 G.SHDSL Port Setup LABEL DESCRIPTION Default VLAN ID Type the Port VLAN ID (PVID) from 1 to 4094. The IES-1000 assig ns the PVID to untagged frames or priority frames (0 VID) received on this port. GVRP GVRP (GARP VLAN Registration P rotocol) is a registration protocol that defines[...]

IES-1000 User ’s Guide 12-10 G .SHDSL Module Port Setup Table 12-6 Add G.SHDSL N-wire Group LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen. N-wire Group Name Type a name to identify this n-wire group. Mode Select how many wires to physi cally bundle together into an N-wire group and which side of the connection this n[...]

IES-1000 User ’s Guide G .SHDSL Module Port Setup 12-1 1 Figure 12-7 Add G.SHDSL Port Bonding Table 12-7 Add G.SHDSL Port Bonding LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen. Bonding Name Type a name to identify this port bonding group. Mode Select the type of bonding units that you w ant to bond together into a po[...]

IES-1000 User ’s Guide 12-12 G .SHDSL Module Port Setup Table 12-7 Add G.SHDSL Port Bonding LABEL DESCRIPTION Available Ports /Available Groups When you select a 2-wire mode, the screen displays the available ports (those that are not members of an n-wire grou p or another port bondi ng group). Select the member ports for thi s port bonding group[...]

IES-1000 User ’s Guide Virtual Channel Management 13-1 This chapter shows you how to configure virtual channels. T he configuration of virtual channels is the same for both the AAM1008 and SAM1008 network modules. 13.1 About V irtual Channels Defining channels (also calle d Permanent Virtual Circuits or PVCs) allows you to set priorities for diff[...]

IES-1000 User ’s Guide 13-2 Virtual Channel Management 13.1.3 VC Mux VC Mux is a type of encapsulation where, by prior mutual agreement, each protocol is assigned to a specific virtual circuit, for example, VC1 carries IP, VC2 carries IPX, and so on. VC-based multiplexing may be dominant in environments where dynamic creation of larg e num bers o[...]

IES-1000 User ’s Guide Virtual Channel Management 13-3 Table 13-1 DSL Port Channel Setup LABEL DESCRIPTION Edit Port Setup Click this link to go to the Edit Port Setup screen. Port Setup Click this link to go to the Port Setup screen. VPI/VCI This field displays the Virtual Path Identifie r (VPI) and Virtual Circui t Identifier (VCI). The VPI and[...]

IES-1000 User ’s Guide 13-4 Virtual Channel Management V ariable Bit Rate (VBR) The Variable Bit Rate (VBR) ATM traffic class is used w ith bursty connections. Connections that use the Variable Bit Rate (VBR) traffic class can be grouped into real time (rt-VBR) or non-real time (nrt-VBR) connections. The rt-VBR (real-time Variable Bit Rate) ty pe[...]

IES-1000 User ’s Guide Virtual Channel Management 13-5 Sustained Cell Rate (SCR) Sustained Cell Rate (SCR) is the mean cell rate of eac h bursty traffic source. It specifies the maximum average rate at which cells can be sent over the virtual c onnection. SCR may not be greater than the PCR. Maximum Burst Size (MBS) Maximum Burst Size (MBS) is th[...]

IES-1000 User ’s Guide 13-6 Virtual Channel Management Burst T olerance (BT) Burst Tolerance (BT) is the maximum number of cells that the port is guaranteed to handle without any discards. BT controls the time scale over which the SCR is enforced. BT is used to determine if a cell arrived too early in relation to SCR. Use this formula to calculat[...]

IES-1000 User ’s Guide Virtual Channel Management 13-7 Figure 13-4 DSL Port VC Profile Setup Table 13-2 DSL Port VC Profile Setup LABEL DESCRIPTION Channel Setup Click this link to go to the Channel Setup screen. Profile Name This name identifies the profile. Encap. This field displays the type of encapsulation ( LLC or VC ). AAL This field displ[...]

IES-1000 User ’s Guide 13-8 Virtual Channel Management DSL Port VC Profile Add or Edit Screen Do the following to open th e VC Profile screen: Step 1. Click a DSL port's index number in the Port Setup screen to go to the DSL Port Setup screen. Step 2. Click Channel Setup in the DSL Port Setup screen to go to the Channel Setup screen. Step 3.[...]

IES-1000 User ’s Guide Virtual Channel Management 13-9 Table 13-3 DSL Port VC Profile Add LABEL DESCRIPTION Class Select cbr (constant bit rate) to specify fixed (alwa ys-on) bandwidth for voice or data traffic. Select ubr (unspecified bit rate) for application s that are non-time sensitive, such as e-mail. Select rt-vbr (real time variable bit r[...]

IES-1000 User ’s Guide 13-10 Virtual Channel Management Figure 13-6 DSL Port Channel Add Table 13-4 DSL Port Channel Add LABEL DESCRIPTION Channel Setup Click this link to go to the port's Channel Setup screen. VPI Type the Virtual Path Identifier for this port. VCI Type the Virtual Circuit Identifier for this port. Active Select this check [...]

IES-1000 User ’s Guide Virtual Channel Management 13-1 1 Table 13-4 DSL Port Channel Add LABEL DESCRIPTION Apply Click Apply to save your changes back to the I ES-1000's volatile memory. The IES-1000 loses these changes if it is turned off or lose s power, so use the Config Save link in the navigation panel on the left to save your changes t[...]

Advanced Applications and Management IV Part IV: Advanced Applications and Management This part describes the Advanced Applications and Advanced Management web configurator screens and troubleshooting.[...]

IES-1000 User ’s Guide S tatic Route 14-1 This chapter explains how to configure static rout es for the IES-1000. 14.1 S tatic Route Overview The web configurator allows you to set up static routes that tell the IES-1000 how to forward management traffic when you configure the TCP/IP parameters manually. 14.2 S tatic Route Setup Screen Click Stat[...]

IES-1000 User ’s Guide 14-2 S tatic Route 14.2.1 Add S tatic Route Screen Click Static Route Setup in the navigation panel to open the Static Route screen and then click Add to open this screen. Use this menu to configure a static route. Figure 14-2 Add Static Route The following table describes this screen. Table 14-2 Add Static Route LABEL DESC[...]

IES-1000 User ’s Guide S tatic Route 14-3 Table 14-2 Add Static Route LABEL DESCRIPTION Apply Click Apply to save your changes back to the IES-1000's volatile memory. The IES-1000 loses these changes if it is turned off or lose s power, so use the Config Save link on the navigation panel to the left to save your cha nges to the non-volatile [...]

[...]

IES-1000 User ’s Guide VLAN 15-1 This chapter explains how to configure VLANs on the IES-1000. 15.1 VLAN Overview A VLAN (Virtual Local Area Network) allows a physical ne twork to be partitioned into multiple logical networks. Stations on a logical network belong to one group. A sta tion can belong to more than one group. With VLA N, a station ca[...]

IES-1000 User ’s Guide 15-2 VLAN TPID 2 Bytes User Priority 3 Bits CFI 1 Bit VLAN ID 12 bits TPID has a defined value of 8100 (hex). The first three bits of the TCI define user priority (giving eight priorit y levels). The CFI (Canonical Format Indicator) is a single- bit flag, always set to zero for Ethernet switches. The remaining twelve bits d[...]

IES-1000 User ’s Guide VLAN 15-3 added and deleted using GARP VLAN Registration Protocol (GVRP), where GARP is the Generic Attribute Registration Protocol. 15.5 Automatic VLAN Registration GARP and GVRP are the protocols used to automati cally register VLAN membership across switches. 15.6 GARP GARP (Generic Attribute Registration Protocol) allow[...]

IES-1000 User ’s Guide 15-4 VLAN Table 15-1 GARP Terminology Port VID This is the VLAN ID assi gned to untagged frames that this port received (in Port Setup). Acceptable Frame Type Whether tagged only or both untagged frames a re accepted on this port. VLAN Port Port Filtering If set, the IES-1000 discards incoming frames for VLANs whi ch do not[...]

IES-1000 User ’s Guide VLAN 15-5 Table 15-2 Static VLAN Setup LABEL DESCRIPTION Management VLAN ID The management VLAN ID is the number of the VLAN through which you manage the IES- 1000. The management VLAN defines which ports you can use to manage the IES-1000. You cannot manage the IES-1000 via a port that is not a member of the mana gement VL[...]

IES-1000 User ’s Guide 15-6 VLAN The following table describes this screen. Table 15-3 Add VLAN Static Entry LABEL DESCRIPTION VLAN Setup Click this link to go to the Static VLAN Setup screen. VLAN ID This is the ID number of VLAN group index number you clicked in the Static VLAN Setup page. Name Type a name to identify the VLAN. Port Number This[...]

IES-1000 User ’s Guide SNMP 16-1 This chapter explains how to configure Simple Network Management Protocol (SNMP). 16.1 SNMP Management SNMP (Simple Network Management Pr otocol) is a protocol used for exchanging m anagement information between network devices. The IES-1000 supports SNMP versions one and two (SNMPv1 and SNMPv2) agent functionalit[...]

IES-1000 User ’s Guide 16-2 SNMP Base (MIB) is a collection of managed objects. SNMP a llows manager and agents to communicate for the purpose of accessing these objects. SNMP itself is a simple request/response protocol based on the manager/agent model. The manager issues a request and the agent returns responses using the following protocol ope[...]

IES-1000 User ’s Guide SNMP 16-3 16.2 SNMP Setup Screen Click SNMP in the navigation panel to open the SNMP screen. Figure 16-2 SNMP Setup The following table describes this screen. Table 16-2 SNMP Setup LABEL DESCRIPTION Trust Host The trusted host, your IES-1000 will only respond to SNMP messages from this addre ss. If you leave the field set t[...]

IES-1000 User ’s Guide 16-4 SNMP Figure 16-3 Add SNMP Access Entry The following table describes this screen. Table 16-3 Add SNMP Access Entry LABEL DESCRIPTION SNMP Setup Click this link to go to the SNMP Setup page. Trusted Host If you enter a trusted host, your IES-1000 w ill only respond to SNMP messages from this address. If you leave the fi[...]

IES-1000 User ’s Guide Logins 17-1 This chapter explains how to change the IES-1000’s passwords. 17.1 Logins Overview The Logins screen allows you to configure the administrator password. 17.2 Logins Screen Click Logins in the navigation panel to open the Logins screen. Use the Logins screen to set administrator passwords for the IES-1000. It i[...]

IES-1000 User ’s Guide 17-2 Logins Table 17-1 Logins LABEL DESCRIPTION Apply Click Apply to save your changes back to t he IES-1000's volatile memory. The IES- 1000 loses these cha nges if it is turned off or loses powe r, so use the Config Save link in the navigation panel on the left to save your changes to the non-volatile mem ory when yo[...]

IES-1000 User ’s Guide Maintenance 18-1 This chapter explains how to use the maintenance screens to set the Unix syslog parameters and remote management; as well as perform firmware and configuration file maintenance. 18.1 Maintenance Overview The Maintenance screen allows you to set UNIX sy slog parameters. It also provides links to the Secured [...]

IES-1000 User ’s Guide 18-2 Maintenance Table 18-1 Maintenance LABEL DESCRIPTION Backup Configuration Use the Backup link to save your cu rrent configuration to a computer. UNIX System Log Select this check box to activate syslog (UNIX system loggin g ) and then configure the UNIX syslog parameters d escribed in the following fields. System Log I[...]

IES-1000 User ’s Guide Maintenance 18-3 Table 18-2 Secured Client Setup LABEL DESCRIPTION Secured Enable Select this check box to allow these secured client s to manage the IES-1000. Do not select this check box unless the IP address that you are usi ng to manage the IES-1000 is already configured as one of the cli ent addresses below. The IES-10[...]

IES-1000 User ’s Guide 18-4 Maintenance Table 18-3 Add Secured Client LABEL DESCRIPTION Secured Client Setup Click this link to go to the Secured Client Setup screen. Secured Client Address Set the IP address of a computer that you want to allow Telnet, FTP or Web access to this IES- 1000. If you enter an IP address in this field, the IES-1000 ch[...]

IES-1000 User ’s Guide Maintenance 18-5 Figure 18-4 Firmware Upgrade 18.2.3 Restore Configuration Screen Click Maintenance in the navigation panel and then Restore Configuration to open the Restore Configuration screen. Use the Restore Configuration screen to restore a previously saved configuration from your computer to the IES- 1000. Click Main[...]

IES-1000 User ’s Guide 18-6 Maintenance 18.2.4 Backup Configuration Screen Click Maintenance in the navigation panel and then Backup Configuration to open the Backup Configuration screen. Use the Backup Configuration screen to save the current configuration of the IES-1000 to a computer. Click Maintenance to return to the main maintenance screen.[...]

IES-1000 User ’s Guide St a t i s t i c s 19-1 This chapter explains the Advanced Management Statistics screens. 19.1 S tatistics Overview The web configurator provides statistics screens to allo w you to see how much traffic the IES-1000 is handling and how it is handling it. 19.2 S tatistics Screen Click Statistics in the navigation panel to op[...]

IES-1000 User ’s Guide 19-2 S tatistics Table 19-1 Statistics LABEL DESCRIPTION DSL Driver | Modem Code Conversion This field displays the version of DSL dri ver and modem code. Hardware Monitor Click this button to display temperature statistics. Port Statistics Click this button to display statis tics for the port s. Channel Statistics Click th[...]

IES-1000 User ’s Guide St a t i s t i c s 19-3 Table 19-2 Hardware Monitor LABEL DESCRIPTION Status This field displays Norma l for temperatures bel ow the threshold and Error for those above. Poll Interval(s) The text box displays how often (in seconds ) this scre en refreshes. You may change the refresh interval by typing a new num ber in the t[...]

IES-1000 User ’s Guide 19-4 S tatistics Table 19-3 Port Statistics LABEL DESCRIPTION State This field shows wheth er a port is turned on ( enable ) or off ( disable ). TxPkts This field shows the n umber of frames tran smitted by this port since the netwo rk module last restarted or the statistics were last manually cle ared via command. RxPkts T[...]

IES-1000 User ’s Guide St a t i s t i c s 19-5 Table 19-4 Channel Statistics LABEL DESCRIPTION System Uptime This field shows how long the system ha s been ru nning since the last time it was started. Port This refers to the DSL port number. VPI This field displays the ch annel’s Virtual Path Identifier (VPI). The VPI and VCI identify a channel[...]

IES-1000 User ’s Guide 19-6 S tatistics Figure 19-5 VLAN Status The following table describes this screen. Table 19-5 VLAN Status LABEL DESCRIPTION Index This is the VLAN index number. VID This is the VLAN ID number config ured in the Edit Static VLAN page. Egress Port Ports that have been added to this VLAN are listed h ere in numerical order. U[...]

IES-1000 User ’s Guide Diagnostic 20-1 This chapter explains the Advanced Management Diagnostic screens. 20.1 Diagnostic Overview The IES-1000 provides diagnostic screens to aid in troubleshooti ng. 20.2 Diagnostic Screen Click Diagnostic in the navigation panel to open the Diagnostic screen. Use this screen to check system logs, reset the system[...]

IES-1000 User ’s Guide 20-2 Diagnostics Table 20-1 Diagnostic LABEL DESCRIPTION Reset Syst em Click this button to restart the IES-1000. A warning dialog box displays asking if you're sure you want to restart the system. Click OK to proceed. Clear System Log Click this button to clear the log of events in the multi-line text box. IP Type the[...]

IES-1000 User ’s Guide Diagnostic 20-3 Table 20-3 Log Messages LOG MESSAGE TYPE DESCRIPTION ADSL <port> Link Down(SN=<seq no>) WARN An ADSL port lost its connection. <port> - port number <seq no> - sequence number of the connection ADSL <port> Link Up(SN=<seq no>): <us rate>/<ds rate> WARN An ADSL p[...]

IES-1000 User ’s Guide 20-4 Diagnostics Table 20-3 Log Messages LOG MESSAGE TYPE DESCRIPTION GSHDSL <port> Link Info: NM=<noise margin> ATT=<loop attenuation> INFO This log displays information about a G.SHDSL p ort’s connection. <port> - port number <noise margin> - the connection’s signal quality in dB. <loo[...]

IES-1000 User ’s Guide Diagnostic 20-5 Table 20-3 Log Messages LOG MESSAGE TYPE DESCRIPTION THERMO RELEASE OVER RANGE: dev:<device id> value:<temp> WARN The temperature detected in the netwo rk module has come back to normal. <temp> - temperat ure when the entry was logged Insecure Telnet From <ip addr> WARN Someone tried [...]

IES-1000 User ’s Guide 20-6 Diagnostics Table 20-4 DSL Line Diagnostic LABEL DESCRIPTION Port This refers to the DSL port number. Select a port upon which you want to perform a loopba ck test. Local Loopback Click this to perform a local loopback test on the specified DSL po rt. A local loopback test is used to check the device's DSL chip. A[...]

IES-1000 User ’s Guide Diagnostic 20-7 Figure 20-4 Logout[...]

[...]

IES-1000 User ’s Guide T roubleshooting 21-1 This chapter covers potential problem s and possible remedies. After each problem description, some steps are provided to help you to diagnose and t o solve the problem. 21.1 DSL LED(s) A DSL LED is not on. Table 21-1 Troubleshooting the DSL LED(s) STEPS CORRECTIVE ACTION 1 Make sure the DSL port is en[...]

IES-1000 User ’s Guide 21-2 T roubleshooting 21.3 DSL LED(s) T urn On and Off A DSL LED turns on and off intermittently. Table 21-3 Troubleshooting a Non-Constant DSL LED STEPS CORRECTIVE ACTION 1 Check the IES-1000’s diagnostic scre en. 2 Connect a DSL modem directly to the DSL port of the IES-1000 using a different telephone wire. If the DSL [...]

IES-1000 User ’s Guide T roubleshooting 21-3 21.8 Local Server The computer behind a DSL modem or router cannot access a local server connected to the IES-1000. Table 21-7 Troubleshooting a Local Server STEPS CORRECTIVE ACTION 1 Refer to section 21.2 to make sure that the su bscriber is able to transmit to the IES-1000. 2 Make sure the computer b[...]

Commands V Part V: Commands This part gives informati on on commands for the IES-1000[...]

[...]

IES-1000 User ’s Guide Commands Introduction 22-1 This section introduces the command line interface and lists the available commands. 22.1 Command Line Interface Overview In addition to the web configurator, you can use commands to configure the IES-1000. It is recommended that you use the web configurator for everyday manageme nt of the IES-100[...]

IES-1000 User ’s Guide 22-2 Commands Introduction [on|off] means that you can use either on or off . 5. “Command” refers to a command used in the command line interface (CI co mmand). Using commands not documented in this User’s Guide can damage the unit and possibly render it unusable. 22.3.1 Help Facility The system includes a help facili[...]

IES-1000 User ’s Guide Commands Introduction 22-3 Table 22-1 Commands MODULE COMMAND DESC RIPTION bridge config save Saves the bridge’s run time configuration to nonvolatile memory. print Shows the bridge’s run time configuration. reset Reloads the bridge’s run ti me configuration from nonvolatile memory. device Shows the bridge settings. a[...]

IES-1000 User ’s Guide 22-4 Commands Introduction Table 22-1 Commands MODULE COMMAND DESC RIPTION enable [1 | 2] Turns on IGMP snooping. 1 sets unknown-discard mode, 2 sets unknown-flood mode. disable Turns off IGMP snooping. timeout [<seconds>] Sets how long the IES-1000 retains entries in the multicast filtering database. mfilter Displays[...]

IES-1000 User ’s Guide Commands Introduction 22-5 Table 22-1 Commands MODULE COMMAND DESCRIPTION <n> Shows buffer <n> in the current buffer pool. steal <num> Steals <num> buffers from the current buffer pool. version Displays version information for the buffer driver. bun version Displays the bun driver’s version. build [...]

IES-1000 User ’s Guide 22-6 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION read <addr> Reads the MII register of the device with the selected PHY address. write <addr> <data> Writes data to the MII register of the device with selected the PHY address. chips cpu Shows CPU usage. debug Starts debug mode (ATMO[...]

IES-1000 User ’s Guide Commands Introduction 22-7 Table 22-1 Commands MODULE COMMAND DESCRIPTION <process> Shows the controlled resources in the specified process. <process> <resource> Shows the value of the specified resource in a process. <process> <resource> <value> Sets the value of a process’s re source.[...]

IES-1000 User ’s Guide 22-8 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION disable <port> Disables 802.1X security on the specified po rt. control <port> <auto|auth| unauth> Sets how the specified port shoul d be authenticated. reauth <port> <on|off> Turns re-authentication on or off on the spec[...]

IES-1000 User ’s Guide Commands Introduction 22-9 Table 22-1 Commands MODULE COMMAND DESCRIPTION fsck Does a file system check in the current partition. <partition> Does a file system che ck in the specified partition. format Formats the current partition. <partition> Formats the specified partition. id <n> Shows the chip ID of [...]

IES-1000 User ’s Guide 22-10 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION version Shows the version information of file system. adsl The adsl commands apply to the AAM module. config save Saves configuration of the ADSL module to nonvolatile memory. enable ch <port> <vpi> <vci> Enables the specified PVC c[...]

IES-1000 User ’s Guide Commands Introduction 22-1 1 Table 22-1 Commands MODULE COMMAND DESCRIPTION pvcs <muxMode> <txvpi> <txvci> [<rxvpi> <rxvci>] Sets the PVC configuration to all ADSL ports. vcp <profile name> <encap> <aal> <class> <pcr> <cdvt> [<scr/mcr> <bt/nrm>] C[...]

IES-1000 User ’s Guide 22-12 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION loopback <portNo> local | f5 Does a local/OAM F5 loopback test on the specified GSHDSL port. stat ch <port> <vpi> <vci> Shows the statistics of the specified PVC channel. chs [<start port> [<end port>]] Shows the s[...]

IES-1000 User ’s Guide Commands Introduction 22-13 Table 22-1 Commands MODULE COMMAND DESCRIPTION bondc <bond name> <port list> or bondc <mode> <bond name> <group list> Bonds the specified member list an d sets them to STU-C mode. bondr <bond name> <port list> or bondr <mode> <bond name> <g[...]

IES-1000 User ’s Guide 22-14 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION chs [<start port> [<stop port>]] Shows the contents of all PVC channels in all ports o r in the specified ports. vcp <profile name> Shows the contents of the specific VC profile. vcps Shows the contents of all VC profiles. list port[...]

IES-1000 User ’s Guide Commands Introduction 22-15 Table 22-1 Commands MODULE COMMAND DESCRIPTION ip arp add <if> <ip> <mac> Adds ARP record <ip> <mac> to interface <if>. delete <if> <ip> Deletes ARP record <ip> from interface <if>. flush Flushes all cache d ARP record s. list Lists all [...]

IES-1000 User ’s Guide 22-16 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION delete <netName> Deletes a subnet. flush Removes all sub nets. version Shows the version information for the IP module. isfs trace Shows the ISFS trace level. <level> Sets the ISFS trace level. version Shows version information for the IS[...]

IES-1000 User ’s Guide Commands Introduction 22-17 Table 22-1 Commands MODULE COMMAND DESCRIPTION facility <facility> Sets the syslog facility. server <ip> Sets the syslog server IP. secured host Shows the secured host. enable | disable Enables or disables che cking for the secured host . add <hostIp> Adds a secured host. delete[...]

IES-1000 User ’s Guide 22-18 Commands Introduction Table 22-1 Commands MODULE COMMAND DESCRIPTION list Shows the VLAN’s current status periodically. stop Stops showing the VLAN’s current status periodically. pvid Lists the default port VLAN ID for all ports. <portNo> <vid> Sets the default port VLAN ID for a specific port. priorit[...]

IES-1000 User ’s Guide System Commands 23-1 Chapter 23 System Commands This chapter describes the IES-1000’ s system-related commands. 23.1 System Commands Overview Use the commands described in this chapter to configure system functions on the IES-1000. 23.2 Commonly Used Commands This section shows you commonly used commands. 23.2.1 Uptime Co[...]

IES-1000 User ’s Guide 23-2 System Commands This command changes the management password. The management password is used for authentication at console or Telnet login. This command is only allowed for local console management sessions. The management password must be from 1 to 8 characters long and any ch aracter is accepted. The factory default[...]

IES-1000 User ’s Guide System Commands 23-3 192.168.1.1 sys> set contact [<name>] This command allows you to set the name of the contact person for your IES-1000. The previous setting will be cleared if the command is entered with the name omitted. 23.3.4 Set Location Command Syntax: 192.168.1.1 sys> set location [<name>] This c[...]

IES-1000 User ’s Guide 23-4 System Commands where <chassis number>= The number for this IES-1000 chassis (1 to 64). This command sets a number to identify this IES-1000 in a network. This is an op tional parameter to help network administrators keep track of multiple IES- 1000s. Enter the command without the chassis num ber to display the I[...]

IES-1000 User ’s Guide System Commands 23-5 23.5 UNIX Syslog Commands Use UNIX syslog commands to send logs to your UNIX server. If the DSL link is on or goes down, the IES-1000 will send a log to your UNIX server. The table, shown next, indicates what is logged in each case. Table 23-1 Logs Sent to Your UNIX Server DSL LINK ON DSL LINK DOWN port[...]

IES-1000 User ’s Guide 23-6 System Commands This command sets the UNIX server IP address. If <server IP>=0.0.0.0 (default), then logs will be dropped (not be sent). 23.6 System Error Log Commands The system error log will record error events locally to the IES-1000 memory. You may clear or display these logs using the commands listed in thi[...]

IES-1000 User ’s Guide ADSL Commands 24-1 The ADSL (Asymmetrical Digital Subscriber Line) subsystem allows yo u to configure and monitor the ADSL ports on the AAM1008 network module. 24.1 ADSL Overview See the web configurator chapter on ADSL for background inform ation about ADSL. 24.2 Configured V ersus Actual Rate You configure the maximum rat[...]

IES-1000 User ’s Guide 24-2 ADSL Commands The config save command saves the ADSL configuration into nonvolatile memory. 24.3.2 Disable Port Command Syntax: 192.168.1.1 adsl> disable port <port number> where <port number> = port number, from 1 to 8. The disable port command forcibly disables the specified ADSL port. The factory defa[...]

IES-1000 User ’s Guide ADSL Commands 24-3 24.3.5 Enable Ports Command Syntax: 192.168.1.1 adsl> enable ports The enable ports command forcibly enables all ADSL ports. The factory default of all ports is disabled. A port must be enabled before data transmission can occur. An enabled but disconnected ADSL port generates more heat than an operati[...]

IES-1000 User ’s Guide 24-4 ADSL Commands An example is shown next. Figure 24-1 Linedata Command Example 24.3.7 Lineinfo Command Syntax: 192.168.1.1 adsl> lineinfo <port number> where <port number> = A port number, from 1 to 8. The lineinfo command shows the line operating values of an ADSL port. An example is shown next. Figure 24[...]

IES-1000 User ’s Guide ADSL Commands 24-5 The results contain the operating modes, interleave delay, parity byte assignment and parity bytes per codeword, symbols per codeword and interleave depth. Information ob tained prior to training to steady state transition will not be valid or will be old inform ation. Annex A refers to POTS. Table 24-1 L[...]

IES-1000 User ’s Guide 24-6 ADSL Commands Down/up stream Depth value This is the current downstream or upstream, interle aved codeword depth value. The larger the number, the more interleave blocks data is distribu ted across and the stronger the protection against errors (and the lower the performa nce is). The smaller the number, the fewer inte[...]

IES-1000 User ’s Guide ADSL Commands 24-7 Downstream (ds) refers to data from the ATU-C and upstrea m (us) refers to data from the ATU-R. “I” stands for interleaved and “ni” stands for non-interleaved (fast mode). A block is a set of consecutive bits associated with the path; each bit belongs to one and only one block. Consecutive bits ma[...]

IES-1000 User ’s Guide 24-8 ADSL Commands An example is shown next. Figure 24-4 Linerate Command Example These results contain the current downstream and upstream operating values (SHOWTIME) for the requested line, the latest available downstream and upstream margins, channel attenuation and the ma ximum attainable rate. Downstream and upstream m[...]

IES-1000 User ’s Guide ADSL Commands 24-9 24.3.12 List Ports Command Syntax: 192.168.1.1 adsl> list ports The list ports command shows the configured maximum rates, modes and states of all ADSL ports. 24.3.13 Set Profile Command Syntax: 192.168.1.1 adsl> set profile <name> [fast] <atur max rate > <atuc max rate> [ldly <[...]

IES-1000 User ’s Guide 24-10 ADSL Commands The profile is a table that contains information on ADSL line configuration. Each entry in this table reflects a parameter defined by a manager, which can be used to configure the ADSL line. Note that the default value will be used fo r any of the above fields that are omitted. The upstream rate must be [...]

IES-1000 User ’s Guide ADSL Commands 24-1 1 24.3.15 List Profiles Command Syntax: 192.168.1.1 adsl> list profiles The list profiles command displays all of the ADSL ports and that profile is assigned to each one. An example is shown next. This display shows that there are two profiles (DEFVAL and debu g) and that port 4 belongs to the debug pr[...]

IES-1000 User ’s Guide 24-12 ADSL Commands Figure 24-6 Show Profile Command Example 24.3.17 Show Profiles Command Syntax: 192.168.1.1 adsl> show profiles The show profiles command displays the settings of all the ADSL profiles. 24.3.18 Set Port Command Syntax: 192.168.1.1 adsl> set port <port number> <profile name> <oper mode[...]

IES-1000 User ’s Guide ADSL Commands 24-13 The mode parameter specifies the standard that this po r t is allowed. When set to auto, the AAM1008 follows whatever mode is set on the other end of the line. An nex A refers to ADSL over PO TS and Annex B refers to ADSL over ISDN. When the mode is set to auto and the negotiated mode is G.lite, if the c[...]

IES-1000 User ’s Guide 24-14 ADSL Commands where <port number> = A port number, from 1 to 8. The show port command shows the line status (up or down) , the actual upstream/downstream rates and mode of an individual ADSL port. 24.3.21 Show Ports Command Syntax: 192.168.1.1 adsl> show ports The show ports command shows the line status (up [...]

IES-1000 User ’s Guide ADSL Commands 24-15 24.3.23 Set PVCs Command Syntax: 192.168.1.1 adsl> set pvcs <multiplexing mode> <tx vpi> <tx vci> [<rx vpi> <rx vci>] where multiplexing mode = either “ llc ” or “ vc ” <tx vpi> = The VPI setting of the ADSL ports for use with a Tx based network <tx vci&g[...]

[...]

IES-1000 User ’s Guide G .SHDSL Commands 25-1 The G.SHDSL (G.991.2 Single-pair High-speed Digital Subscriber Line) subsystem allows you to configure and monitor the G.SHDSL ports on the SAM1008 network module. 25.1 G . SHDSL Overview Refer to the web configurator chapter on G.S HDSL for background inform ation on G.SHDSL. 25.2 Configured V ersus [...]

IES-1000 User ’s Guide 25-2 G .SHDSL Commands 192.168.1.1 gshdsl> config save This command saves the G.SHDSL configuration into non volatile memory. You must use this command to save any configurations that you make, otherwise the IES-1000 will return to its de fault settings when it is restarted. Do not turn off your IES-1000 while saving you[...]

IES-1000 User ’s Guide G .SHDSL Commands 25-3 25.3.5 Enable Ports Command Syntax: 192.168.1.1 gshdsl> enable ports This command forcibly enables all G.SHDSL ports. 25.3.6 Lineinfo Command Syntax: 192.168.1.1 gshdsl> lineinfo <port #> where <port #> = A port number, from 1 to 8 This command shows the line operating values of a G.[...]

IES-1000 User ’s Guide 25-4 G .SHDSL Commands where <Port> = The port number on the SAM1008. <Sp> = The line rate. If Sp=0 , then the connection is down. <NM> = Noise Margin. The noise margin in decibels. <ATTEN> = Attenuation. The loop attenuation in de cibels. <ES> = Errored Second. The total number of one- second [...]

IES-1000 User ’s Guide G .SHDSL Commands 25-5 Mode = This field displays which port bonding or n-wire mode the port is set to use. “Normal” displays when the port is not p art of an n-wire group. “2-wire” displays when the port is part of a port bonding group (but not part of an n- wire group). “4-wire” displays when the port is part [...]

IES-1000 User ’s Guide 25-6 G .SHDSL Commands <Cmin> = The minimum transmission rate in Kbps. This setting is optional. 192 Kbps is the default if you do not configure a value for this parameter. Setting Cmax and Cmin to the same rate fixes the rate for that port. annexA | annexB = The Power Spectral Density region, omitted for annexB. Conf[...]

IES-1000 User ’s Guide G .SHDSL Commands 25-7 An example is shown next. This display shows that there are two profiles (DEFVAL and gold) and that p ort 3 belongs to the gold profile while ports 1, 2, 4 , 5, 6, 7 and 8 belong to the DEFVAL profile. Figure 25-2 List Profiles Command Example 25.3.13 Show Profile Command Syntax: 192.168.1.1 gshdsl>[...]

IES-1000 User ’s Guide 25-8 G .SHDSL Commands 192.168.1.1 gshdsl> show profiles The show profiles command displays the settings of all the G.SHDSL profiles. 25.3.15 Set Port Command Syntax: 192.168.1.1 gshdsl> set port <port #> <profile name> where <port #> = The number of the port to which you want to assign a profile. &l[...]

IES-1000 User ’s Guide G .SHDSL Commands 25-9 networks. The <rx vpi> and <rx vci> settings will be equal to those of <tx vpi> and <tx vci> if the rx settings are not configured. The set pvc command allows the configuration of a PVC (p ermanent virtual circuit) for an individual G.SHDSL port. 25.3.18 Set PVCs Command Syntax[...]

IES-1000 User ’s Guide 25-10 G .SHDSL Commands 25.3.21 Display All G .SHDSL Line Information Syntax: 192.168.1.1 gshdsl> monitor [<start port> [<stop port>]] where <start port> = The first port number in a range of ports for which you want to display line information. 1 is used if you leave this blank. <stop port> = The[...]

IES-1000 User ’s Guide G .SHDSL Commands 25-1 1 Make sure that G.SHDSL ports five through eight are all the same end of their connections (all STU-C or all STU- R). G.SHDSL ports one through four do not need to be set to be the same end of the connection as G.SHDSL ports five through eight. For exam ple, G.SHDSL ports one th rough four could be s[...]

IES-1000 User ’s Guide 25-12 G .SHDSL Commands Make sure that G.SHDSL ports five through eight are all the same end of their connections (all STU-C or all STU- R). G.SHDSL ports one through four do not need to be set to be the same end of the connection as G.SHDSL ports five through eight. For exam ple, G.SHDSL ports one th rough four could be se[...]

IES-1000 User ’s Guide G .SHDSL Commands 25-13 Make sure that G.SHDSL ports five through eight are all the same end of their connections (all STU-C or all STU- R). G.SHDSL ports one through four do not need to be set to be the same end of the connection as G.SHDSL ports five through eight. For exam ple, G.SHDSL ports one th rough four could be se[...]

IES-1000 User ’s Guide 25-14 G .SHDSL Commands G.SHDSL ports one through four do not need to be set to be the same end of the connection as G.SHDSL ports five through eight. For exam ple, G.SHDSL ports one th rough four could be set t o be STU-C while G.SHDSL ports five through eight are set to be STU-R. The following example sets an STU-R port b[...]

IES-1000 User ’s Guide G .SHDSL Commands 25-15 192.168.1.1 gshdsl> delete nwire <group name> where <group name> = The name of the n-wire group. This command removes the specified n-wire group. An example is shown next. 192.168.1.1 gshdsl> delete N-wire-A This removes the n-wire group so the ports function a s individual ports as[...]

IES-1000 User ’s Guide 25-16 G .SHDSL Commands 25.3.31 List Bonded Members Command Syntax: 192.168.1.1 gshdsl> list bond The list bond command displays all of the bonded members. An example is shown next. 192.168.1.1 gshdsl> list bond Port-bonding configuration: Bonding name Mode Member list -------------------------------+-------------+---[...]

IES-1000 User ’s Guide Virtual Channel Management 26-1 This chapter shows you how to use commands to configure virtual channels. 26.1 About V irtual Channels See the web configurator chapter on virtual channel mana gement for background inf ormation on virtual channels. The configuration of virtual channels is the sam e for both the AAM and SAM n[...]

IES-1000 User ’s Guide 26-2 Virtual Channel Management <scr/mcr> = The Sustained Cell Rate (scr) sets the av erage cell rate (long-term) that can be transmitted. SCR applies with the rt-vbr and nrt-vbr traffic classes. Min imum C ell R ate (mc r) is t he mi nimum rate at which the sender can send cells. MCR applies with the abr traffic clas[...]

IES-1000 User ’s Guide Virtual Channel Management 26-3 26.2.3 Delete VCPs Command Syntax: 192.168.1.1 adsl> delete vcps The delete vcps command deletes all of the virtual channel profiles, except the DEFVAL profile. You cannot delete a virtual channel profile that is assigned to any of the network m odule’s DSL channels. Assign a different p[...]

IES-1000 User ’s Guide 26-4 Virtual Channel Management 26.3 PVC Channels Channels (also called Permanent Virtual Circuits or PVCs) let you set priorities for different services or subscribers. You can define up to eight channels on each DSL port and use the m for different services or levels of service. You set the PVID that is assigned to untagg[...]

IES-1000 User ’s Guide Virtual Channel Management 26-5 The delete ch command deletes the specified PVC channel. The following example deletes the PVC channe l for port 8 that uses VPI 0 and VCI 33. 192.168.1.1 adsl> delete ch 8 0 33 26.3.3 Delete Channels Command Syntax: 192.168.1.1 adsl> delete chs [<start port> [<stop port>]] [...]

IES-1000 User ’s Guide 26-6 Virtual Channel Management 26.3.5 Show Channels Command Syntax: 192.168.1.1 adsl> show chs [<start port> [<stop port>]] where <start port> = The first port number in a range of ports for which you want to display line information. 1 is used if you leave this blank. <stop port> = The last port[...]

IES-1000 User ’s Guide Virtual Channel Management 26-7 where <start port> = The first port number in a range of ports for which you want to display line information. 1 is used if you leave this blank. <stop port> = The last port number in a range of ports for which you want to display line information. 8 is used if you leave this blan[...]

IES-1000 User ’s Guide 26-8 Virtual Channel Management 192.168.1.1 adsl> stat ch <port> <vpi> <vci> where <port> = A port number (1 to 8) or (*) means all 8 ports. <vpi> = The VPI setting (0 to 255). <vci> = The VCI setting (32 to 65535 if vpi = 0) or (1 to 65535 if the vpi d oes not = 0). The stat ch comman[...]

IES-1000 User ’s Guide Virtual Channel Management 26-9 Figure 26-6 Channel Statistics Command Example 26.3.12 Clear Channel Command Syntax: 192.168.1.1 adsl> clear ch <port> <vpi> <vci> where <port> = A port number (1 to 8) or (*) means all 8 ports. <vpi> = The VPI setting (0 to 255). <vci> = The VCI setting[...]

[...]

IES-1000 User ’s Guide 10/100M Fast Ethernet Port Commands 27-1 The Ethernet subsystem allows you to configure and monitor the 10/100M fast Ethernet port. 27.1 10/100M Fast Ethernet Overview Refer to the web configurator chapter on the ADSL m odule ports for backgrou nd information on the 10/100M auto-sensing Ethernet ports. 27.2 Ethernet Command[...]

IES-1000 User ’s Guide 27-2 10/100M Fast Ethernet Port Commands <speed> = 10 or 100 This command sets the connection speed used when auto-negotiation is turned off. 10 stands for 10Mbps and 100 stands for 100Mbps. 27.2.4 S tatus Command Syntax: 192.168.1.1 ethernet> status This command shows the current status of the Ethernet port.[...]

IES-1000 User ’s Guide Bridge Commands 28-1 This chapter discusses the bridge subsystem . It allows you to configure and monitor the bridging, configure MAC filters, port-based VLANs (port filter) and tagged frame functions of t he IES-1000. 28.1 Bridge Commands Overview See the web configurator Getting Started Screens chapter for background info[...]

IES-1000 User ’s Guide 28-2 Bridge Commands 192.168.1.1 bridge> status This command displays the bridge manageme nt statistics. 28.4 MAC Filter Commands Use MAC filter commands to filter incoming frames based on MAC (Media Access Control) address(es) that you specify. If you do not use this command, your IES-1000 will not filter frames. MAC fi[...]

IES-1000 User ’s Guide Bridge Commands 28-3 <port> = A bridge port number. <mac> = The source MAC address in "00:a0:c5:12:34:56" format. This command adds a source MAC address fixed on a speci fied port. You may add up to five MAC addresses. 28.4.5 MAC Filter Delete Command Syntax: 192.168.1.1 bridge> macfilter delete <[...]

IES-1000 User ’s Guide 28-4 Bridge Commands where ID = The location of the entry in the multicast filtering database. VID = The VLAN ID of the entry in the multicast filtering database. GDA = Group Destination Address. The IP address of a multicast group destination. MAC = The last 3 bytes of the multicast MAC that the GDA is mapped to. Member Po[...]

IES-1000 User ’s Guide Bridge Commands 28-5 28.5.6 Ethertype Command Syntax: 192.168.1.1 bridge> ethertype [<port> <any|ip|pppoe>] where <port> = A bridge port number. any = The filter allows all packet types to be forwarded to and from the specified port. ip = The filter allows IP packets only to be forwarded to and from the[...]

IES-1000 User ’s Guide 28-6 Bridge Commands An example with an altered configuration is shown next. 192.168.1.1 > bridge 192.168.1.1 bridge> portfilter 2 1 3 192.168.1.1 bridge> portfilter 3 1 2 This example sets the allowed outgoing bridge ports of por t 2 (DSL port 1) to p ort 1 (Ethernet port) and port 3 (DSL port 2). The allowed outg[...]

IES-1000 User ’s Guide Bridge Commands 28-7 Figure 28-5 Example of Modified Port Filter Port 3 The following figure illustrates that port 1 (the Ethernet port) is linked to ports 2 (DSL port 1) and 3 (DSL port 2). Ports 2 (DSL port1) and 3 (DSL port 2) are also linked to each other. Or, in other words, the following figure is a result of the foll[...]

IES-1000 User ’s Guide 28-8 Bridge Commands <port> = The port number on the network module. Port 0 is t he CPU’s port, port 1 is the Ethernet port and ports 2-9 are the br idge ports on net work module modules. These are logical ports. <vid> = The tag number (or IEEE 802.1Q identification) that identifies the source port of an Ether[...]

IES-1000 User ’s Guide DHCP Relay Commands 29-1 This chapter describes how to use the DHCP Relay commands. 29.1 DHCP Relay Overview Refer to the web configurator part for background inf ormation on DHCP. 29.2 DHCP Relay Commands Use these commands to configure the DHCP relay feature. 29.2.1 Add Command Syntax: 192.168.1.1 dhcprelay> add <ip[...]

IES-1000 User ’s Guide 29-2 DHCP Relay Commands The delete command removes the specified DHCP server or all servers fro m the list of servers to which the IES- 1000 relays client TCP/IP configuration requests. 29.2.4 Enable Command Syntax: 192.168.1.1 dhcprelay> enable This command turns on the DHCP relay feature. 29.2.5 Disable Command Syntax[...]

IES-1000 User ’s Guide DHCP Relay Commands 29-3 29.2.8 S tatus Command Syntax: 192.168.1.1 dhcprelay> status The status command displays whether or not the DHCP relay feature is activated. 29.2.9 T race Command Syntax: 192.168.1.1 dhcprelay> trace The trace command activates trace option(s). 29.2.10 Untrace Command Syntax: 192.168.1.1 dhcpr[...]

IES-1000 User ’s Guide 29-4 DHCP Relay Commands 192.168.1.1 dhcprelay> relayinfo disable The relayinfo disable command turns off the DHCP relay agen t information (Option 82) feature. 29.3.3 Relayinfo S tatus Command Syntax: 192.168.1.1 dhcprelay> relayinfo status The relayinfo status command displays the current status of th e DHCP relay a[...]

IES-1000 User ’s Guide IEEE 802.1X Commands 30-1 This chapter describes how to use the dot1x commands. 30.1 IEEE 802.1X Overview The IES-1000 supports IEEE 802.1X port-b ased authentication (refer to the web configurator part for background information). 30.2 IEEE 802.1X Commands Use these commands to configure the IEEE 802.1X feature. 30.2.1 Ena[...]

IES-1000 User ’s Guide 30-2 IEEE 802.1X Commands where [level] = Use 1 to turn on the packet debug level. This has the IES-1000 display the contents of EAPOL (Extensible Authentication Protocol Over LAN) frames. This can help you determine whether or not the subscriber is sending IEEE 802.1X packets. If necessary, customer support may instruct yo[...]

IES-1000 User ’s Guide IEEE 802.1X Commands 30-3 30.2.8 Port Re-authentication Command Syntax: 192.168.1.1 dot1x> port reauth <port> <on|off> where <port> = A port number (1 to 8). <on|off> = Use on to require a subscriber to periodica lly re-enter his or her username and password to stay connected to the po rt (some IE[...]

IES-1000 User ’s Guide 30-4 IEEE 802.1X Commands <addr> = The IP address of the external RADIUS server. This command sets the external RADIUS server IP address. 30.2.12 RADIUS Port Command Syntax: 192.168.1.1 dot1x> radius port <portnum> where <portnum> = The UDP port number of the external RADIUS server. This command sets th[...]

IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-1 This chapter generally describes the IEEE 802.1Q Tagged VLAN and associated CI Commands. 31.1 IEEE 802.1Q T agged VLAN Introduction The IEEE 802.1Q Tagged VLAN allows your network module to deliver tagged/untagged fra mes to and from its ports. The standard gives the network module the[...]

IES-1000 User ’s Guide 31-2 IEEE 802.1QT agged VLAN Commands Example: 1. 192.168.1.1> vlan1q 2. 192.168.1.1 vlan1q> svlan setentry 11 2 fixed untag 3. 192.168.1.1 vlan1q> svlan setentry 11 1 fixed tag 4. 192.168.1.1 vlan1q> pvid 2 11 5. 192.168.1.1 vlan1q> svlan setentry 12 3 fixed untag 6. 192.168.1.1 vlan1q> svlan setentry 12 [...]

IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-3 2. 192.168.1.1 vlan1q> vlan enable 31.3 IEEE 802.1Q T agged VLAN Commands Bridge port 1 stands for the Ethernet port, bridge port 2 stands for DSL port 1, bridge port 3 stands for DSL port 2, and so on. 31.3.1 VLAN Enable Command The default for the IEEE 802.1Q Tagged VLAN is disabl[...]

IES-1000 User ’s Guide 31-4 IEEE 802.1QT agged VLAN Commands This command sets the VLAN ID to a specific port in the PVID table. To display the PVID table simply enter this command without parameters, as shown next. Figure 31-1 Example: PVID Command Display Make sure you set all bonded ports to have the same PVID. 31.3.4 SVLAN CPU Command Syntax:[...]

IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-5 This command displays the static VLAN registration tabl e. The following figure is an example of what is displayed when you use this command. Figure 31-2 Example: SVLAN List Command Display For more information about the Svlan List command display, refer to the Svlan Setentry command ([...]

IES-1000 User ’s Guide 31-6 IEEE 802.1QT agged VLAN Commands Modify a S tatic VLAN T able Example The following is an example of how to modify a static VLAN table. 1. 192.168.1.1 vlan1q> svlan setentry 3 3 fixed untag 2. 192.168.1.1 vlan1q> svlan setentry 2 2 fixed untag 3. 192.168.1.1 vlan1q> svlan setentry 1 1 fixed tag 4. 192.168.1.1 [...]

IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-7 Figure 31-4 SVLAN Example An untagged frame comes in from the LAN. The switch checks the PVID table and assigns a temporary VID of 1. The switch ignores port# 1 (the LAN port where the frame came in), because the switch does not send a frame to the port that it came in through. The swi[...]

IES-1000 User ’s Guide 31-8 IEEE 802.1QT agged VLAN Commands 31.3.7 SVLAN Getentry Command Syntax: 192.168.1.1 vlan1q> svlan getentry <vid> where <vid> = A VLAN ID. Valid parameter range = [1 – 4094]. This command displays an entry with a speci fied VLAN ID in the static VLAN table. Display a S tatic VLAN T a ble Entry Example Th[...]

IES-1000 User ’s Guide IEEE 802.1Q T agged VLAN Commands 31-9 Figure 31-6 Example: DVLAN List Command Display In the figure above, “ || ” denotes “filter” and “ >> ” denotes “forward”. 31.3.10 DVLAN Getentry Command Syntax: 192.168.1.1 vlan1q> dvlan getentry <vid> where <vid> = A VLAN ID. Valid parameter range[...]

IES-1000 User ’s Guide 31-10 IEEE 802.1QT agged VLAN Commands Figure 31-8 Example: VLAN List Command Display In the figure above “ O " denotes “egress port”, “ V ” denotes “tagged” and “ X ” denotes “ untagged”. vid 01 02 03 04 05 06 07 08 09 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1 O O O O V X X X X X X X X [...]

IES-1000 User ’s Guide IEEE 802.1p Priority Commands 32-1 This chapter explains IEEE 802.1p Priority CI Commands. 32.1 Introduction IEEE 802.1p Priority CI Commands assign priorit y levels to individual ports. IE EE 802.1p defines up to eight priorities (0-7) by inserting a tag into a MAC-layer frame that contains bits to define priority of servi[...]

IES-1000 User ’s Guide 32-2 IEEE 802.1p Priority Commands 32.2.2 Regen Port Command Syntax: 192.168.1.1 vlan1q> regen port [<port #> <user priority> <regenerated priority>] where <port #> = A bridge port number. Valid parameter range = [1 – 9]. <user priority> = The user priority for a frame received on this por[...]

IES-1000 User ’s Guide IP Commands 33-1 This chapter shows you how to configure the IP (Internet Protocol) parameters. The IP host implementation in the IES-1000 allows you to manage it ove r the network. More often than not, you have m ore than one IES-1000 for a particular installation. Before you start configuring the IES-1000s, make sure that[...]

IES-1000 User ’s Guide 33-2 IP Commands 192.168.1.1> ip 192.168.1.1 ip> enable ether 192.168.1.3 255.255.255.0 192.168.1.1 ip> route delete default 192.168.1.1 ip> route add default 0.0.0.0 192.168.1.233 00:00:00:00 192.168.1.1 ip> config save Figure 33-1 Setting IP Address and Default Gateway The IES-1000 leaves the factory with a[...]

IES-1000 User ’s Guide IP Commands 33-3 <host> = The IP address of the target. <ttl> = Time to Live (optional). This parameter lim its the number of hops (routers) that the echo request can travel before it reaches the target. <size> = The parameter specifies the size of the payloa d, that is, not counting the headers, of the ec[...]

IES-1000 User ’s Guide 33-4 IP Commands This command removes all of the subnets. 33.2.8 Route Add Command Syntax: 192.168.1.1 ip> route add <dom name> a.b.c.d <relay> [am:bm:cm:dm [<cost> [<timeout>]]] where <dom name> = The name of the static route. a.b.c.d = The destination IP address of packets th at this stati[...]

IES-1000 User ’s Guide IP Commands 33-5 Syntax: 192.168. 1.1 ip> enable [<if> [mtu <size> [<ip> [<ipmask>]]] where <i/f> = The name of an interface (“ether” for this device). [mtu <size>] = Maximum Transmit Unit. The maximum packet size that this interface is to send. <ip> = The IP address of the d[...]

[...]

IES-1000 User ’s Guide Remote Management 34-1 This chapter shows you how to manage the IES-1000 remotely. 34.1 Remote Management Introduction More often than not, you will have the IES-1000 located re m otely making its remote management features very useful. See the web configurator chapter on SNMP for background inform ation on SNMP. 34.2 Manag[...]

IES-1000 User ’s Guide 34-2 Remote Management 34.3.2 SNMP Access Delete Command Syntax: access delete <community> [<IP addr>] This command revokes SNMP access by the specified community (password). If the IP address is specified, access is denied for that manager station only. 34.3.3 SNMP Access Flush Command Syntax: access flush This[...]

IES-1000 User ’s Guide Remote Management 34-3 34.4.2 T rap Delete Command Syntax: trap delete <community> <IP addr> This command deletes a trap destination. The parameters are the sa me as the trap add command. 34.4.3 T rap Flush Command Syntax: trap flush This command deletes all trap destinations. 34.4.4 T rap List Command Syntax: t[...]

[...]

IES-1000 User ’s Guide Configuration Backup/Restore 35-1 This chapter describes the process f or backing up your user settings (configuration) f rom the network module onto your computer and how to restore them to the network module. The network modules use FTP for configuration backup/r estore through their built-in FTP servers. You can use any [...]

IES-1000 User ’s Guide 35-2 Configuration Backup/Restore Do not turn off the network module during the restore process, as it may corrupt the firmware and make your network module unusable. Connect to the network module with your favorite FTP c lient. The command for the network module is generally C:> ftp < network module IP address> a[...]

IES-1000 User ’s Guide Firmware Upload and Recovery 36-1 This chapter describes how to load new firm ware onto your device, or recover firmware that is in t he non-volatile memory. The network modules use FTP to upload firmware and no longer support TFTP uploads. If the firmware in the non-volatile memory is damaged, the network m odule uses BOOT[...]

IES-1000 User ’s Guide 36-2 Firmware Upload and Recovery Do not turn off the network module during the updating process, as it may corrupt the firmware and make your network module unusable. 1. Connect to the network module with your favorite FTP client. The comm and for the netwo rk module i s generally : ftp < network module IP address> a[...]

IES-1000 User ’s Guide Firmware Upload and Recovery 36-3 4. Run BootpTftp.exe , to bring up the following window. Click New to create a MAC address entry. Figure 36-1 BOOTP/TFTP Server 5. The Input Box window will pop up as shown next. Type the MAC address of the network module and then click OK . You can find the MAC address of the network modul[...]

IES-1000 User ’s Guide 36-4 Firmware Upload and Recovery Figure 36-3 Database Edit Dialog 7. Select Normal Bootp to enable normal BOOTP/TFTP functions. Figure 36-4 Enable BOOTP/TFTP 8. Restart the network module and press any key w ithin three seconds to get the following screen. Figure 36-5 Enter Debug Mode 9. Press any key at the “ Press any [...]

IES-1000 User ’s Guide Firmware Upload and Recovery 36-5 10. Enter atnb at the network module boot console. 11. Wait for the firmware upload to finish. 12. Use the following command sequence on the network module to write new firmware to flash memory. 192.168.1.1> flashfs 192.168.1.1 flashfs> wipe 192.168.1.1 flashfs> update 13. Wait for[...]

[...]

IES-1000 User ’s Guide T roubleshooting 37-1 Chapter 37 T roubleshooting This chapter covers potential problem s and possible remedies. After each problem description, some steps are provided to help you to diagnose and t o solve the problem. 37.1 SHDSL or ADSL LED(s) An SHDSL or ADSL LED is not on. Table 37-1 Troubleshooting the DSL LED(s) STEPS[...]

IES-1000 User ’s Guide 37-2 T roubleshooting 37.3 SHDSL or ADSL LED(s) T urn On and Off An SHDSL or ADSL LED turns on and off intermittently. Table 37-3 Troubleshooting a Non-Constant DSL LED STEPS CORRECTIVE ACTIO N 1 Use the lineinfo command with G.SHDSL (refer to 25.3.6 ) or th e linerate command with ADSL (refer to 24.3.9) to check th e subsc[...]

IES-1000 User ’s Guide T roubleshooting 37-3 Table 37-5 Troubleshooting Port Bonding STEPS CORRECTIVE ACTIO N 3 Swap the telephone wiring between the non-t ran smitting port and one of the bonded group’ s transmitting ports. For example, SHDSL ports 1 and 2 are bonde d. Port 2 is transmitting but port 1 is being dropped. Connect port 2’s tele[...]

IES-1000 User ’s Guide 37-4 T roubleshooting Table 37-7 Troubleshooting the Password CORRECTIVE ACTIO N Refer to section 36.2 to update your firmware. All settings will retu rn to default values, so any configurations you have made will be lost. 37.8 Local Server The computer behind a DSL modem or router cannot access a local server connected to [...]

IES-1000 User ’s Guide T roubleshooting 37-5 Table 37-10 Troubleshooting Telnet STEPS CORRECTIVE ACTIO N 3 If you are attempting to telnet from the DSL side of the network module, refer to section 37.2 to make sure that you can transmit data to the network module. 4 If you are attempting to telnet from the Ethernet side of the network module, che[...]

Appendices and Index VI Part VI: Appendices and Index This part gives appendices and an index.[...]

IES-1000 User ’s Guide Safety W arnings A Appendix A Safety W arnings  Refer to the Hardware Specifications appendix for the gauge of wire to use for each connection.  The length of exposed (bare) IES-1000 power wire should not exc eed 7mm.  Do not use this product near water, for example, in a wet basement.  Only a qualified technici[...]

[...]

IES-1000 User ’s Guide Removing and Installing a Fuse C Appendix B Removing and Inst alling a Fuse This appendix shows you how to remove and install fuses for the AC power IES-1000. The AC power IES-1000 uses one 250V-3A fuse. The IES- 1000 comes with two 250V-3A fuses; one is installed at the factory (in the fuse housing) and the other is a sp a[...]

IES-1000 User ’s Guide D Removing and Installing a Fuse Step 4. Gently pull the fuse casing from the IES-1000. The in stalled fuse is located attached to, and on the outside of the fuse housing; the spare fu se is located inside the fuse housing. Diagram 2 Accessing the Spare Fuse Step 5. Remove the burnt-out fuse from the IES-1000. A burnt-out f[...]

IES-1000 User ’s Guide PIN Assignments E Appendix C Pin Assignment s Mini RJ-1 1 4P4C (Console Port) Pin Assignment s Diagram 3 RJ-11 4P4C (Console Port) Pin Assignments RJ-1 1 6P2C (SHDSL Port s on the SAM1008 and ADSL USER or CO Port s on the AAM1008) Pin Assignments Diagram 4 RJ-11 6P2C (SHDSL Port) Pin Assignments[...]

IES-1000 User ’s Guide F PIN Assignments Note that a 2, 4 or 6 pin connector can be used with this port provided pins 3 and 4 connect to a SAM1008 SHDSL port. RJ-45 (LAN Port) Pin Assignments Diagram 5 RJ-45 (LAN Port) Pin Assignments 1 = TX+ 8 = Not Connected 2 = TX- 7 = Not Connected 3 = RX+ 6 = RX- 4 = Not Connected 5= Not Connected[...]

IES-1000 User ’s Guide Hardware S pecifications G Appendix D Hardware S pecifications Physical Interfaces IES-1000 • Two slots for a total of up to two hot-swappable DSL network m odules • Power receptacle • 19” 1U rack-mountable, wall-mountable unit • Each network module has one mini RJ-11 console port for local configuration an d mana[...]

IES-1000 User ’s Guide H Hardware S pecifications • One AAM1008 = 1.1 kg Wire Gauge S pecifications Chart 1 Wire Gauge Specifications WIRE TYPE REQUIRED AWG NO. (DIAMETER) Telephone Wire 26 or larger DC Power Model IES-1000 Power Wire 16 to 18 American Wire Gauge (AWG) is a measure ment system for wire that sp ecifies its thickness. As the thic[...]

IES-1000 User ’s Guide Index I Index # #2 Philips Screwdriver 4-1 1 10 Mbps Ethernet 7-2 10/100M Auto-Sensing Ethernet 11-7 100 Mbps Ethernet 7-2 4 4-wire 12-1 8 802.1x Edit Screen 10-20 8-wire 12-1 A AAL 13-7 AAM1008 Connections 6-5 ABR 13-4, 13-7 AC INPUT 6-12 Access Delete Command 34-2 Access Flush Command 34-2 Access List Command 34-2 Actual [...]

IES-1000 User ’s Guide J Index C CBR 13-3, 13-7 CDVT 13-5, 13-7 CE Mark Warning iii Cell Delay Variation Tolerance 13-5 Central Side Port Bonding Command 25-12 Certifications iii Channel Attenuation 24-8 Channel Statistics Command 26-7 Channels Statistics Comm and 26-8 Chassis 1-1 Chassis ID 10-1 CI Commands 22-2 Clear Channel Comm and 26-9 Clear[...]

IES-1000 User ’s Guide Index K Disclaimer ii Display All G.SHDSL Line Information 25-10 Downstream 11-7 Downstream (ds) 24-7 Downstream Max Rate: Kbps 11-5 Duplex 8-3 DVLAN Getentry Command 31-9 DVLAN List Command 31-8 DVLAN Table 15-2 E Enable Channel Command 26-6 Enable Channels Command 26-6 Enable Command 33-4 Enable Port Command 24-2, 25-2 En[...]

IES-1000 User ’s Guide L Index G.SHDSL Compliance 1-1 G.SHDSL modem 8-2, 8-3 G.SHDSL Module Port Setup 12-3 G.SHDSL Port 8-2 G.SHDSL Ports (SAM1008) 2-1 G.SHDSL Profile Add or Edit 12-6 G.SHDSL Profile Setup 12-5 G.SHDSL Standards 27-2 GARP 15-3 General IP Commands 33-2, 35-1 General Setup 10-1 General Syntax Conventions xxi GetNext 16-2 Glossary[...]

IES-1000 User ’s Guide Index M LEDs 3-2 Lightening G Limited Warranty iv Line Bit Allocation 24-3 Line Delay Command 24-8 Line Operating Values 24-4, 25-3 Line Performance Counters 24-6, 25-3 Line Rate Parameters 24-7 Linedata Command 24-3 Lineinfo Command 24-4, 25-3 Lineperf Command 24-6, 25-3 Linerate Command 24-7 List Bonded Members Command 25[...]

IES-1000 User ’s Guide N Index Network Modules 1-1 NIC See Network Interface Ca rd Non real-time Variable Bit Rate 13-4, 13-7 NRM 13-4, 13-7 nrt-VBR 13-7 nrt-VBR) 13-4 Number of Resource Manageme nt 13-4 Number of Resource Manageme nt Cells 13-7 N-wire 12-9, 25-10 N-wire Mode 12-1 O Online Registration xxi Operating Environment 4-1 Operational mo[...]

IES-1000 User ’s Guide Index O Rack-Mounted IES-1000 Installation 4-1 RADIUS (Remote Authent ication Dial-In User Service) 10- 17 RADIUS IP Command 30-3 RADIUS Port Command 30-4 RADIUS Secret Command 30-4 RADIUS Show Command 30-4 Real-time Variable Bit Rate 13-4, 13-7 Regen Port Command 32-2 Related Documentation xxii Relayinfo Add Command 29-4 R[...]

IES-1000 User ’s Guide P Index Set Port Command 24-12, 25-8 Set Ports Command 24-13, 25-8 Set Profile Command 24-9, 25-5 Set PVC Command 24-14, 25-8 Set PVCs Command 24-15, 25-9 Set Remote Side N-wire Mode Command 25-11 Set Remote Side Port Bonding Command 25-13 Set Slot Command 23-3 Set Speed Command 27-1 Set VCP Command 26-1 Setting IP Address [...]

IES-1000 User ’s Guide Index Q Syslog Server Command 23-5 System Commands 23-1 System Error Log Commands 23-6 System Error Logging 1-3 System Name 10-1 T Table of Contents vi Tagged Ethernet Frames 28-7 Taiwanese BSMI A Warning iii Target SNR (db) 11-7 TAT 13-6 Telco Rack Space 1-4 Telephone Wire H Telnet 6-1, 34-1 Tempera ture G Terminal emulati[...]

IES-1000 User ’s Guide R Index Tags 31-1 Unware Device s 31-1 VLAN Acceptable Frame Type 11-9, 11-11, 12-9 VLAN Disable Command 31-3 VLAN Enable Command 31-3 VLAN List Command 31-9 VPI 13-10 VT100 3-1, 22-1 W WAN Link 8-3 Warning Sticker 6-12 Warnings A, iii Warranty iv Weight G Wire Gauge H Wiring Testing 8-4 Working Fans 8-1 Z ZyXEL Web Site xx[...]