Whirlpool 9400000 инструкция обслуживания

THE RAZZA PLUS WHIRLPOOL B ATH R Owner's Manual P ortable Whirlpool Spa TM[...]

IMPORT ANT SAFETY INFORMA TION READ AND FOLLOW ALL INSTRUCTIONS Jacuzzi Whirlpool Bath does not recommend spa water temperatures in excess of 104 F. High water tempera- tures in excess of 104 F. and prolonged periods of use can raise internal human body temperature excessively and impair the body’s ability to regulate its internal temperature. Li[...]

Contents Installation Instructions _________________________________________ 2-5 Inspection and Shipping Claim ___________________________________________ 2 Unpacking ___________________________________________________________ 2 Positioning Your Spa ___________________________________________________ 3 Electrical Requirements ______________________[...]

Specifications and Installation Instructions 909 lbs. (414 kg.) ELECTRICAL REQUIREMENTS 230 VAC 50 AMPS 60 Hz. Separate Circuit 4 Wire .75 HP 230 VAC 4.8 AMPS 3450 RPM Single Phase 60 Hz. WHIRLPOOL MOTOR/ PUMP DIMENSIONS SHIPPING WEIGHT Razza 9400000 87" L. (221 cm) 87" W. (221 cm) 37" H. (94 cm) MODEL PRODUCT SPECIFICATIONS ARE SUBJ[...]

INST ALLA TION INSTRUCTIONS 2 Inspection and Shipping Claim Check for shipping damage upon receipt of the spa. Jacuzzi Whirlpool Bath is not responsible for damage to the spa sustained during shipping. If damage is evident before unpacking, see instructions regarding shipping claims on the outside of the carton and immediately file a claim with the[...]

3 Important: Read complete instructions before beginning installation. Positioning Y our Spa Because your Razza Plus spa is portable, you can locate it just about anywhere you wish--on a deck,patio, or even indoors. Just be sure to position it above ground in an area with good drainage and on a level, continuous surface which can support the weight[...]

4 Electrical Precautions CAUTION: Do not apply electrical power to the spa unless it is filled with water to the normal water level, which is approx. 9" below the spa rim (see location of water level indicator on face of skimmer on page 13). If the spa's motor/pumps are actuated when there is not sufficient water in the unit, the circulat[...]

5 Equipment Set-Up 1. Remove the plastic sheet covering the spa. Use care; stepping into the spa with shoes will scratch the acrylic surface. 2. Remove any packing materials from the spa. 3. Remove each filter cartridge from its plastic bag. 4. Pull open each skimmer/filter door by the handle located in the middle of the door and remove the skimmer[...]

OPERA TING INSTRUCTIONS • Using a garden hose, fill the spa with water to the water line indicator mark on the skimmer frame. • At the house service panel, turn on the circuit breaker or switch that controls the electrical service to your spa. (Make sure there is no other appliance on that circuit.) • Open the skirt door giving access to the [...]

SYSTEM CONTROL MODULE • Make sure the circuit protector buttons are pushed in. • Locate the HIGH TEMPERATURE SAFETY SWITCH which is a raised button on the end of the heater. Push this button to be sure it is in the reset mode. The purpose of this switch is to shut down the spa if the water becomes excessively hot. If, for some reason, the switc[...]

air blower and light. Refer to the Control Panel illustra- tion for an explanation of the various switch functions. SYSTEM The SYSTEM switch controls the following four func- tions in the continuous sequence indicated: 1. OFF 2. JETS 3. HTR/FLTR 4. FILTER (The next selection is OFF again.) Use the JETS function as a reference to indicate your locat[...]

Set the HEATER knob by rotating it to the desired temperature. When the water temperature is lower than that set by the HEATER knob, the heater and filter motor/ pump will be activated. The heater and filter functions will automatically turn off when the desired temperature is reached. When the heater is on, the water is also being filtered. The he[...]

10 HIGH VOLUME FULLY ADJUSTABLE WHIRLPOOL JET SILENT AIR CONTROLS OPERA TION MA XIMUM AI R OU TP U T (C OUNTE R CL OCK W IS E RO T ATION) MA XIMUM AI R OU TP U T (CL OCK WISE RO TATI ON) WHIRLPOOL W ATE R JE T S ON LY Normal Operation Whirlpool System You can enjoy the Razza Plus spa with or without activating the whirlpool. Either way, bathing in [...]

W ater Quality and W ater Chemistry Maintaining water quality and water chemistry in your spa is extremely important and should be a regular part of your spa maintenance program, as a neglected spa can be a breeding place for dangerous bacteria. The water quality of your spa is maintained by a combination of filtration and chemistry. The spa’s in[...]

Balancing pH: For good hygiene and equipment longevity, maintain the pH of your spa water according to the instructions provided. pH is the measure to determine if the spa water is too acid (low pH) or too alkaline or basic (high pH). The ideal range for spa water is 7.2 to 7.6 pH. For excessive acidity (below 7.2 pH) add soda ash or sodium bicarbo[...]

WA TE R LEVEL I NDI CA T OR MA RK FILTE R CA RTR IDGE SKI MMER BASKET W ater Level/Drain The water level in the spa must be maintained at its normal level. Evaporation and splashing will cause the water level to drop. When concentrations of impurities from evaporation, water quality chemicals, body oils, perfumes, dirty feet, and winds, etc., accum[...]

Automatic Filtration/Maintenance If you plan to be away, you should maintain minimum water quality by running the filter system. To do this, set the timer to turn the system on for at least two hours each day. This will cause the filter system to turn on at a desired time. Set the timer according to instructions on page 7 with the SYSTEM switch OFF[...]

Cleaning Y our Spa Your Razza Plus spa shell consists of two layers of plastic materials. Its smooth top surface of acrylic is tough and durable and contains concentrated color. This is supported by a substantial thickness of fiber- glass-reinforced polyester resin. A catalyst causes a chemical reaction during manufacture that bonds these layers pe[...]

16 REMEDY PROBLEM PROBABLE CAUSE 3. Heater not functioning but heater light on. A. Heater plug loose. B. Element malfunction. C. Relay malfunction. A. Check Heater Plug connection System Control Module. B. * C. * 5. Abnormal water usage. A. Leak in suction line, discharge line, or connections. B. Excessive evaporation and/or splashing. A. Repair le[...]

PROBLEM * Note: The skills and tools necessary for the safe repair of this spa require the services of qualified service personnel. Contact your Jacuzzi Whirlpool Bath Authorized Service Agent or Dealer. 17 REMEDY PROBABLE CAUSE 7. No water flow from jets. A. Power turned off. B. Selector switch in OFF. C. House circuit breaker tripped; no power to[...]

B. Spa is up to temperature set PROBABLE CAUSE REMEDY PROBLEM A. Timer is functioning. 13. Accessory Switch and system switch in off position, but motor and heater still operating. A. Normal function. Turn timer to an off position, or reset tabs in off position. A. System and/or accessory switch is not in off position. A. Turn both system switch an[...]

Optional 1-1/2" Permanent Drain If you wish to connect a permanent drain line to the 1- 1/2" plumbing of the spa, you may modify the plumbing as shown in illustration B on this page. Note that none of the piping required for the modification is provided. 19 A WE I R BLAD E SPA SHE LL LEVEL B Leveling the Cascade First make sure spa is in [...]

©1988 Jacuzzi Whirlpool Bath C788000 8/92 Printed in the U.S.A. Printed on Recycled Paper Jacuzzi Whirlpool Bath National Headquarters P.O. Drawer J, Walnut Creek, CA 94596 (510) 938-7070 Service Support: Call (800) 288-4002 Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for product[...]