Wachsmuth & Krogmann PCSD180T инструкция обслуживания

CIRCULAR SAW INSTRUCTION MANUAL Item#3729 MODEL NO: PCSD180T PLEASE READ THESE INSTRUCTIONS CAREFULL Y TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL[...]

FUNCTIONAL DESCRIPTION Figure-1 1 FUNCTIONAL DESCRIPTION Figure 2 CLOCKWISE TO LOOSEN COUNTER CLOCKWISE TO TIGHTEN SWING NUT CUTTING DEPTH Figure-3 2[...]

FUNCTIONAL DESCRIPTION F i g u r e - 4 Figure-5 3 LIST OF MAIN P AR TS 1) B a t t e r y p a c k 6 ) N u t 2) U p p e r g u a r d 7 ) S a w b l a d e 3) B a s e 8 ) S w i t c h l o c k 4) F l a n g e 5) Lower guard Figure 6 9) ON/OFF switch CLAMP NUT TECHNICAL SPECIFICA TIONS : Description PCSD180T Rating V oltage 18V olts Nominal power 200W No-load[...]

2 3 4 5 F i g u r e - 7 Figure-8 GENERAL S AFETY RULES W ARNING! Read and understand all instru ctions. Failure to follow al l instructions listed b elow may result in electric s hock, fire or serious personal injury . SA VE ALL INSTRUCTIONS! WORK AREA 1. Keep your wo rk area clean and well organize d. Cluttered benches and dark areas invite accide[...]

situations. 6. Use safety equipment. Always wear eye protection. Dust mask, no n-skid safety shoes, hard hat, or hearing pro tection must be used for ap propriate conditions. TOOL USE AND CARE 1. Use clam ps or other practical way to se cure and support the workpiece to a stable platfor m. Holding the w ork by hand or a gainst your body is unstable[...]

guard is cover ing the blade before placing the saw dow n on bench or floor . Be aware of the time it take s for the blade to stop after switch is rel eased. 7. NEVER hold piece being cut in yo ur hand or across the legs. It is im portant to support th e work properly to m inimize body exposure, bla de binding, or loss of control. 8. Always use bla[...]

on a soft surface that might block the v entilation slots and result in excessive internal heat. Place the char ger in a position away from any heat source. 11. Do not operate char ger if it has received a sharp blow , been dropped, or otherwise damaged in any way . T ake charger to an a uthorized service center . 12. Do not disassem ble charge r ,[...]

use the correction screw . Adjusting the Cutting depth (See Fig.3&4) For the cleanest possible cut, set the c utting depth whene ver possible 5 mm deeper than the thic kness of the material. Slacke n the swing nut for adjusting depth of cut, set t he cutting depth, and tighten the swi ng nut again. Adjusting the cutting angle Slacken the sw ing[...]

2) Insert the batt ery pack into t he charger , as shown in Fi g 7, making sur e the pack is fu lly seated in the char ger . The red light indi cator will illuminate sho wing that the bat tery is being char ged. 3) When char ging is well done green light will illum inate. The minim um charg e time is normally 1hour after which the battery should be[...]

before installing or removing blad e. 1. T o remove th e blade (Fig.8, press th e shaft lock so that the blade ca nnot revolve and use th e hex wrench to l oosen the bolt clock-w ise. Then remove the bolt, outer flange and blade. 2. T o install the blade, follow th e rem oval procedure in reverse. BE SURE TO TIGHTEN THE BOL T SECUREL Y 3. Hold the [...]

ridge.  T o avoid a tearing out of the cutting edges when working sensiti ve area (if the surface is very smooth crepe tape also enables easy drawing of line), fixing a th in board of wood to the wo rkpiece and sawing thro ugh both will also avoid tearing out ef fect ively . ADJUSTING FOR ACCURACY OF 90º CUT (VER TICAL) This adjustm ent has bee[...]

Both brushes should be replaced at the s ame time. Use only identical carbon brushes. Use a screwdriver to rem ove the brush holder caps. T ake out the worn carbon brushes, ins ert the new ones and se cure the brush holder caps. TIPS FOR MAINT AINING MAXIMUM BA TTER Y LIFE 1. Char ge the battery pac k before battery is com pletely dischar ged. Alwa[...]