Vermont Casting 1990 инструкция обслуживания

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Идти на страницу of

Хорошее руководство по эксплуатации

Законодательство обязывает продавца передать покупателю, вместе с товаром, руководство по эксплуатации Vermont Casting 1990. Отсутствие инструкции либо неправильная информация, переданная потребителю, составляют основание для рекламации в связи с несоответствием устройства с договором. В законодательстве допускается предоставлении руководства в другой, чем бумажная форме, что, в последнее время, часто используется, предоставляя графическую или электронную форму инструкции Vermont Casting 1990 или обучающее видео для пользователей. Условием остается четкая и понятная форма.

Что такое руководство?

Слово происходит от латинского "instructio", тоесть привести в порядок. Следовательно в инструкции Vermont Casting 1990 можно найти описание этапов поведения. Цель инструкции заключается в облегчении запуска, использования оборудования либо выполнения определенной деятельности. Инструкция является набором информации о предмете/услуге, подсказкой.

К сожалению немного пользователей находит время для чтения инструкций Vermont Casting 1990, и хорошая инструкция позволяет не только узнать ряд дополнительных функций приобретенного устройства, но и позволяет избежать возникновения большинства поломок.

Из чего должно состоять идеальное руководство по эксплуатации?

Прежде всего в инструкции Vermont Casting 1990 должна находится:
- информация относительно технических данных устройства Vermont Casting 1990
- название производителя и год производства оборудования Vermont Casting 1990
- правила обслуживания, настройки и ухода за оборудованием Vermont Casting 1990
- знаки безопасности и сертификаты, подтверждающие соответствие стандартам

Почему мы не читаем инструкций?

Как правило из-за нехватки времени и уверенности в отдельных функциональностях приобретенных устройств. К сожалению само подсоединение и запуск Vermont Casting 1990 это слишком мало. Инструкция заключает ряд отдельных указаний, касающихся функциональности, принципов безопасности, способов ухода (даже то, какие средства стоит использовать), возможных поломок Vermont Casting 1990 и способов решения проблем, возникающих во время использования. И наконец то, в инструкции можно найти адресные данные сайта Vermont Casting, в случае отсутствия эффективности предлагаемых решений. Сейчас очень большой популярностью пользуются инструкции в форме интересных анимаций или видео материалов, которое лучше, чем брошюра воспринимаются пользователем. Такой вид инструкции позволяет пользователю просмотреть весь фильм, не пропуская спецификацию и сложные технические описания Vermont Casting 1990, как это часто бывает в случае бумажной версии.

Почему стоит читать инструкции?

Прежде всего здесь мы найдем ответы касательно конструкции, возможностей устройства Vermont Casting 1990, использования отдельных аксессуаров и ряд информации, позволяющей вполне использовать все функции и упрощения.

После удачной покупки оборудования/устройства стоит посвятить несколько минут для ознакомления с каждой частью инструкции Vermont Casting 1990. Сейчас их старательно готовят или переводят, чтобы они были не только понятными для пользователя, но и чтобы выполняли свою основную информационно-поддерживающую функцию.

Содержание руководства

  • Страница 1

    Homeowner ’ s Installation and Operating Manual For use in the United States and Canada Do Not Discard This Manual: Retain for Future Use 2000966 2/07 Rev . 19 The Intrepid II W oodburning Stove Model 1990 SAFETY NOTICE: IF THIS APPLIANCE IS NOT PROPERL Y INST ALLED, OPERA TED AND MAIN- T AINED, A HOUSE FIRE MA Y RESUL T . TO REDUCE THE RISK OF F[...]

  • Страница 2

    2 Intrepid II W oodb ur ning Stove 2000966 W elcome All of us at CFM Corporation Ask your V ermont Castings dealer how these instal- lation accessories can enhance the versatility , ap- pearance, and safety of your Intrepid Stove. 0307 Bottom Heat Shield 0172 Rear Heat Shield Chimney connector heat shields Heavy-gauge enamel pipe to match the stove[...]

  • Страница 3

    3 Intrepid II W oodb ur ning Stove 2000966 Specifications Intrepid II, Model 1990 21  " (545 mm) 20" (510 mm) 25  " (640 mm) T op exit flue collar height 21  " (540 mm) 24" (610 mm) 7  " (180 mm) 21  " (545 mm) C L 21  " (540 mm) 18" (460 mm) 1 ?[...]

  • Страница 4

    4 Intrepid II W oodb ur ning Stove 2000966 Installation SAFETY NOTICE: IF YOUR STOVE IS NOT PROP- ERL Y INST ALLED, A HOUSE FIRE MA Y RESUL T . TO REDUCE THE RISK OF FIRE, FOLLOW THE INST AL- LA TION INSTRUCTIONS. CONT ACT LOCAL BUILD- ING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INST ALLA TION INSPECTION REQUIREMENTS IN YOUR AREA. Before you begin[...]

  • Страница 5

    5 Intrepid II W oodb ur ning Stove 2000966 If you use an existing masonry chimney , it must be inspected to ensure safe condition before the stove is installed. Y our local professional chimney sweep, build - ing inspector , or fire department official will be able to inspect the chimney or provide a referral to someone who can. The chimney must [...]

  • Страница 6

    6 Intrepid II W oodb ur ning Stove 2000966 Keep the horizontal run of chimney connector as short and direct as possible, with no more than two 90° turns. Slope horizontal runs of connector upward 1/4” per foot (20mm per m) going from the stove toward the chim- ney . The recommended maximum length of a horizontal run is 3’ (914mm). The recommen[...]

  • Страница 7

    7 Intrepid II W oodb ur ning Stove 2000966 The opening through the chimney wall to the flue (the “breach”) must be lined with either a ceramic or metal cylinder , called the “thimble”, which is cemented firmly in place. The fit must be snug and the joint between the thimble and the chimney wall must be cemented. (Fig. 6) A special piece [...]

  • Страница 8

    8 Intrepid II W oodb ur ning Stove 2000966 Fireplace Chimney Installations - Through a Fireplace If your fireplace height is at least 25” (635mm), you may install an Intrepid II with standard legs through the fireplace opening using a “positive connection” kit available from your local dealer . These positive connec- tion kits ensure a tigh[...]

  • Страница 9

    9 Intrepid II W oodb ur ning Stove 2000966 Y our local dealer or your local building inspector can provide details for other approved methods of passing a chimney connector through a combustible wall in your area. In Canada, this type of installation must conform to CAN/CSA-B365, Installation Code for Solid Fuel Burning Appliances and Equipment. T [...]

  • Страница 10

    10 Intrepid II W oodb ur ning Stove 2000966 Floor Protection for Fireplace Installations Do not assume your fireplace hearth is completely noncombustible. Many fireplace hearths do not satisfy the “completely noncombustible” requirement because the brick or concrete in front of the fireplace opening is supported by heavy wood framing as in F[...]

  • Страница 11

    1 1 Intrepid II W oodb ur ning Stove 2000966 connector) and nearby shields carries away heat. Do not block the air flow by filling this empty space with any insulating material. The shiny shield surface facing the heat source must be left unpainted, enabling it to reflect heat back towards the stove or connector and away from the wall. Shields a[...]

  • Страница 12

    12 Intrepid II W oodb ur ning Stove 2000966 Noncombustible shields installed 1” (25 mm) away from the combustible surface on noncombustible spacers, called ventilated shields, may be used to reduce clear- ances. (Fig. 14) 1" (25mm) 1/4" (6mm) ST501 mantel and trim shield 11/10/00 djt ST501 Fig. 14 A custom-formed mantel shield.[...]

  • Страница 13

    13 Intrepid II W oodb ur ning Stove 2000966 ST503 Alcove side view 1 1/10/00 djt Metal Stud Combustible facing may overlap metal studs by only 1” 1” air gap top and bottom, on both sides and back wall 7/16” Durock® (or equivalent) Joist Shield (Sup- plied by Chimney Manufacturer) ST503 Fig. 17 Alcove side section. St504 Alcov e cutawa y?[...]

  • Страница 14

    14 Intrepid II W oodb ur ning Stove 2000966 Intrepid II Clearance Chart See Pages 15 and 16 for illustrations of these clearances. * Clearances with double-wall connectors and protected surfaces have not been tested for the Intrepid II. 1. Shielding for a top exit stove must include the stove rear heat shield insert to protect the area behind the ?[...]

  • Страница 15

    15 Intrepid II W oodb ur ning Stove 2000966 D E F F C C A B J K L L I I G H ST507 Intrepid Clearance Diagrams  11/00 P Q M N Intrepid II Clearance Diagrams See the chart on Page 14 for dimensions indicated by letter in the diagrams below . Stove Installed Parallel to W all Stove in Corner Stove Installed Parallel to W all Protected Surface[...]

  • Страница 16

    16 Intrepid II W oodb ur ning Stove 2000966 W all Shield Requirements for Some Common Intrepid II Installations IN T R E PI D II C C C C D F A B E D ST508 Intrepid II wall shield 1 1/00 ST508 Fig. 21 Parallel installation, vertical chimney connector , two wall shields. Reduced clearances for both rear and side walls. W all shields may meet at corne[...]

  • Страница 17

    17 Intrepid II W oodb ur ning Stove 2000966 Distance from the Center of the Flue Collar to the W all in T op-Exit Installations The information on this page is helpful in planning stove placement for top-exiting installations, particularly those in- stallations with chimneys that pass through the ceiling. However , this is not a clearance chart. Fi[...]

  • Страница 18

    18 Intrepid II W oodb ur ning Stove 2000966 Clean the Griddle Before Use At the factory the griddle is coated with vegetable oil to prevent rusting while the stove is in transit and storage. Remove the oil with a dry rag or paper towel before you use the stove. Set Up the Stove Remove any loose parts from inside the stove. Place a protective pad on[...]

  • Страница 19

    19 Intrepid II W oodb ur ning Stove 2000966 ST515 reverse flue collar 1 1/17/00 djt Flue Collar Screws ST515 Fig. 30 Reversing the flue collar . Attach the Griddle Handle Install the handle on the griddle. Place the griddle upside down at the edge of a flat surface and assemble the handle as shown. (Fig. 31) With the handle pointing 45° from [...]

  • Страница 20

    20 Intrepid II W oodb ur ning Stove 2000966 A Damper Directs Air Flow Within the Stove The damper handle opens and closes the damper to direct air flow within the stove, and is next to, and to the right of, the primary air control lever on the right side of the stove. (Fig. 34) When the handle points to the floor , the damper is open, letting smo[...]

  • Страница 21

    21 Intrepid II W oodb ur ning Stove 2000966 W ARNING: For safety and greatest efficiency , oper- ate your stove only with all doors/griddles fully closed. The test standard for your stove when it is operated in this mode is UL 1482. Y our stove may be used as a fireplace with the front doors open or removed only when the spark screen is placed co[...]

  • Страница 22

    22 Intrepid II W oodb ur ning Stove 2000966 Use the Air Control Settings that Work Best for Y ou No single air control setting will fit every situation. Set- tings will differ depending on the quality of the fuel, the amount of heat desired, and how long you wish the fire to burn. The control setting also depends on your particular installation?[...]

  • Страница 23

    23 Intrepid II W oodb ur ning Stove 2000966 produce soot or large flakes of char or fly ash that can coat the combustor and cause smoke to spill into the room. Coal smoke also can poison the catalyst so that it won’t operate properly . In general, the fire must be sufficiently well-established to ensure catalytic activity is initiated. When ?[...]

  • Страница 24

    24 Intrepid II W oodb ur ning Stove 2000966 Continue adding split logs of this size to the briskly- burning fire until there is a glowing ember bed at least 3” (75mm) deep. A good ember bed is neces- sary for proper functioning of the catalytic system and may take an hour or more to establish. 5. Close the damper when the griddle temperature rea[...]

  • Страница 25

    25 Intrepid II W oodb ur ning Stove 2000966 A stove is part of a system, which includes the chimney , the operator , the fuel, and the home. The other parts of the system will affect how well the stove works. When there is a good match between all the parts, the system works well. Wood stove operation depends on natural (unforced) draft. Natural dr[...]

  • Страница 26

    26 Intrepid II W oodb ur ning Stove 2000966 Creosote Creosote is a by-product of slow wood-burning. It’s an organic tar that can condense in the flue if it’s dense in the smoke, and slow-moving, and cools off to less than 290°F . Condensed creosote is volatile, and can generate chimney fires if it gets hot enough. All the features that affec[...]

  • Страница 27

    27 Intrepid II W oodb ur ning Stove 2000966 Maintenance Let the fire in the stove go out and allow the stove to cool completely before beginning any maintenance procedure. Care of the Cast Iron Surface An occasional dusting with a dry rag will keep the painted cast iron of your Intrepid looking new . The stove’s paint can be touched up as needed[...]

  • Страница 28

    28 Intrepid II W oodb ur ning Stove 2000966 ST532 damper adj 11/00 Thermostat Cover D-plate Damper Actuator Rod Handle Damper Locking Nut Allen Head Ad - justment Screw ST532 Fig. 45 T ighten the damper adjustment screw for a snug seal. How to Adjust the Door Latch Over time, the gasketing around the doors will com- press, and the latch may n[...]

  • Страница 29

    29 Intrepid II W oodb ur ning Stove 2000966 The Catalytic Combustion System Inspection and Cleaning This wood heater includes a catalytic combustor , which needs periodic inspection and replacement for proper operation. In the United States, it is against the law to operate this wood heater in a manner inconsistent with the operating instructions i[...]

  • Страница 30

    30 Intrepid II W oodb ur ning Stove 2000966 6. Remove the damper housing. It is held in place by two weld screws and two chrome acorn nuts in the back of the stove. Loosen the chrome acorn nuts and rotate the tabs to release the damper housing. Y ou may find it necessary to remove or loosen the thermostat cover to access the one of acorn nuts inst[...]

  • Страница 31

    31 Intrepid II W oodb ur ning Stove 2000966 5. Lay an unbroken 1/8” (3mm) bead of gasket cement in the newly-cleaned channel. Starting at one end, press the gasket into the channel. Ensure a good joint where the gasket meets before trimming any excess. Do not overlap the gasket ends or leave ends with ragged edges. 6. Press the gasketed part fir[...]

  • Страница 32

    32 Intrepid II W oodb ur ning Stove 2000966 • Inspect and clean the catalytic block, and vacuum out the ash at the bottom of the back plate after removing the lower fireback. Lightly clean the refrac- tory assembly that houses the element. Be careful not to damage the refractory material, which is very fragile. • Inspect the secondary probe th[...]

  • Страница 33

    33 Intrepid II W oodb ur ning Stove 2000966 Appendix: Catalytic Combustor In any chemical reaction, including the combustion process, there are certain conditions which must be met before the reaction can take place. For example, a reaction may require a certain temperature, or a certain concentration of the reactants (the combustion gases and oxyg[...]

  • Страница 34

    34 Intrepid II W oodb ur ning Stove 2000966 1 2 3 4 5 6 7 8 9 10 12 13 16 17 18 20 9 21 22 25 26 24 23 21 36 37 38 39 40 41 15 1 1 12 9 42 43 43 27 28 29 30 31 32 33 35 34 0966 Intrepid II exploded view 1 1/00 22a 73 0966 CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and prod[...]

  • Страница 35

    35 Intrepid II W oodb ur ning Stove 2000966 45 46 47 48 49 50 57 52 53 54 60 57 59 68 65 64 63 62 44 55 56 66 67 61 58 51 0966 Intrepid II exploded view 8/02 72 CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. Item Description Part Numbe[...]

  • Страница 36

    36 Intrepid II W oodb ur ning Stove 2000966 Stove Serial No. _____________________ Dealer ____________________________ __________________________________________ __________________________________________ Phone _____________________________ Date Purchased _____________________ Installer ___________________________ __________________________________[...]

  • Страница 37

    37 Intrepid II W oodb ur ning Stove 2000966[...]

  • Страница 38

    38 Intrepid II W oodb ur ning Stove 2000966[...]

  • Страница 39

    39 Intrepid II W oodb ur ning Stove 2000966 W arranty Limited 3 Y ear W arranty CFM Corporation warrants that this woodburning stove will be free of de- fects in material and workmanship for a period of three years from the date you receive it, except that the catalyst, thermostat assembly , handles, glass door panels, cement, and gasketing shall b[...]

  • Страница 40

    © CFM Corporation 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 800-668-5323 • www .cfmcorp.com CFM Corporation[...]