United States Stove 6300C инструкция обслуживания

USSC 1[...]

2 USSC T ABLE OF CONTENTS .............................................................................................. 2 SAFETY PRECAUTIONS ........................................................................................... 3 SPECIFICA TIONS ..................................................................................................[...]

USSC 3 Safety Precautions IMPORT ANT : Read this entire manual before installing and operating this product. Failure to do so may result in property damage, bodily injury , or even death. Proper installation of this furnace is crucial for safe and efficient operation. Install vent at clearances specified by the vent manufacturer . Do not connect th[...]

4 USSC Specifications Input BTU/Hr 1 50,000 to 105,000 BTU/hr . Heating Capacity 2 1,200 - 2,800 sq. ft. Fuel Burn Rate 3 5.0 - 13.0 lbs./hr . Burn T ime (lowest setting) 70 hours continuous Hopper Capacity 320 lbs Heating S pecifications Height 43-1/8 in. Width 28-1/2 in. Depth 39-1/2 in. Weight 250 lbs. Dimensions 1 BTU output will vary depending[...]

USSC 5 Fuel Considerations SHELLED CORN (Dry , preferably corn with 1 1% or less moisture content) • • • • • • • Optimum moisture content of corn should be 1 1% or less. Wet corn will rapidly deteriorate furnace components, reduce efficiency and void all warranties. Purchase a moisture tester if in doubt. Corn must be clean and free f[...]

6 USSC INST ALLA TION OPTIONS Read this entire manual before you inst all and use your Multi-Fuel Furnace. Failure to follow instructions may result in property damage, bodily injury , or even death! (See specific inst allation det ails for clearances and other inst allation requirements) As a Primary Furnace —the unit functions independently of [...]

USSC 7 Installation CLEARANCES NOTE: Distance on the left-hand side of y our Multi-Fuel Furnace is set at 24 inches for suitable access to the control panel and for fuel loading. This distance may be less, but not less than 7 inches.[...]

8 USSC Installation VENTING REQUIREMENTS Inst all vent at clearances specified by the vent manufacturer . Do not connect the pellet vent to a vent serving any other appliance or furnace. Do not inst all a flue damper in the exhaust venting system of this unit. The following installation guidelines must be followed to ensure conformity with both the[...]

USSC 9 Installation VENT TERMINA TION CLEARANCES: A ----- Minimum 4-foot clearance below or beside any door or window that opens. B ----- Minimum 1-foot clearance above any door or window that opens. C ----- Minimum 3-foot clearance from any adjacent building. D ----- Minimum 7-foot clearance from any grade when adjacent to public walkways. E -----[...]

10 USSC Installation THROUGH THE W ALL INST ALLA TION (RECOMMENDED INST ALLA TION) T o vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter . If the exhaust adapter is at least 18-inches above ground level, a straight section of pellet vent pipe can be used through the wall. Y our furnace dealer should be able to pr[...]

USSC 11 Installation PRIMAR Y FURNACE SECONDAR Y (ADD-ON) FURNACE When installed as a seondary furnace, a Duct Damper must be inst alled between the air discharge of the 6300 furnace and the primary (Gas, Electric, etc.). This duct damper prevent s the air from the primary furnace from back flowing to the secondary furnace. Damper must be a mechani[...]

12 USSC Component Location[...]

USSC 13[...]

14 USSC LIGHTING INSTRUCTIONS CAUTION: DO NOT USE CHEMICALS OR FLUIDS TO ST ART THE FIRE HOT WHILE IN OPERA TION. KEEP CHILDREN, CLOTHING AND FURNITURE AW A Y . CONT ACT MA Y CAUSE SKIN BURNS. Before lighting your heater for the first time, make sure that all items are out of the hopper , ash pan and firebox area. Press the “On” button and allo[...]

USSC 15 Maintenance Operation DAIL Y OPERA TION The hopper and furnace top will be hot during operation; therefore, you should always use some type of hand protection when refueling your furnace. Never place your hand near the auger while the furnace is in operation. In the event of a power out age , the furnace WILL NOT function. It is very import[...]

16 USSC INTERIOR CHAMBERS Open the Ash Cleanouts and scrap all ash into the ash p an. Open the damper and allow the ashes to fall into the ash pan. The damper may need to be slide in and out several times to clear any ash build-up. This may need to be done daily depending on fuel consumption. Be sure the ash cleanouts located on either side of the [...]

USSC 17 Parts Diagram[...]

18 USSC Parts List 1 5 9 8 10 12 7 4 6 11 3 2 Item Part No. Title Qt y . 1 25507 Feed Door 1 2 25492 Handle, Door 1 3 83506 3/8 x 1 1/4 Roll Pin 1 4 891053 Door Glass w/o Logo 1 5 88066 5/8” Rope Gasket 4.5 ft 6 88087 Glass Gasket (1 x 1 3/16) 3 ft 7 25520 Bottom Glass Ret ainer 1 8 25521 T op Glass Retainer 1 P ARTS LIST Item Part No. Title Qt y[...]

USSC 19 Wiring Diagram[...]

20 USSC T rouble Shooting PROBLEM CAUSE: Not enough combustion air; Fuel has too much moisture. Viewing window becoming black shortly af ter start-up. • Adjust the air damper to a more open position. • Use a fuel with less moisture content PROBLEM CAUSE: Not enough combustion air; Fuel has too much moisture. “Black Popcorn” is present in th[...]

USSC 21 Err or Codes Below is a chart describing the Error Codes that might be displayed if an error occurs with your furnace. Error Code Err1 Err2 Err3 Err4 Err5 Err6 Err7 Err8 Error Descrption The high limit temperature sensor has tripped. Furnace ran out of fuel during normal operation. The furnace was unable to reach the Room Fan On temperature[...]

22 USSC Notes[...]

USSC 23 Notes[...]

24 USSC THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM YOUR KING OR ASHLEY, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE. WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON THE NAMEPLATE ATTACHED TO THE HEATER. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWIN[...]