United States Stove 2015 инструкция обслуживания

Ussc 1 Owner’s Operation and Instruction Manual Model 2015 C R US SAFETY NOTICE: If this heater is not properly installed, a house fire may result. For your safety, follow the installation instruc- tions. Contact local building or fire officials about restrictions and installation requirements in your area. CAUTION! Read All Instructions Carefull[...]

2 Ussc OPTIONS PART NUMBER Thermodisc AC05530 Outside Air Intake Kit AC02080 CONGRATULATIONS! You've purchased a heater from North America's oldest manufacturer of wood burning products. By heating with wood you're helping to CONSERVE ENERGY! Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply.[...]

Ussc 3 ASSEMBLY Leg Assembly: 1. Remove the firebrick form the unit. Tilt the unit on its side. DO NOT tilt the unit on its back, this could possibly bend or distort the blower chute on the back of the unit . 2. Remove the four(4) Lag Screws holding the two boards to the unit. 3. Mount the legs to the bottom of the unit using the eight bolts, nuts,[...]

4 Ussc BLOWER ASSEMBLY ASSEMBL Y INSTRUCTIONS THE BLOWER ASSEMBLY MUST BE DISCONNECTED FROM THE SOURCE OF ELECTRI- CAL SUPPLY BEFORE ATTEMPTING THE INSTALLATION. Step 1. Fix the assembly to the back of the stove with the four screws provided. T HE BLOWER ASSEMBLY IS INTENDED FOR USE ONLY WITH A STOVE THAT IS MARKED TO INDICATE SUCH USE. DO NOT ROUT[...]

Ussc 5 INSTALLATION SAFETY NOTICE • IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH. • CONSULT YOUR MUNICIPAL BUILDING DEPARTMENT OR FIRE OFFICIALS ABOUT RESTRICTIONS AND [...]

6 Ussc FLOOR PROTECTOR Your wood stove should be placed on a non-combustible surface with a R value of 1.0. For multiple layers, add R-values of each layer to determine the overall R-value. The floor protector should be under the stove, eighteen inches beyond the front and eight inches beyond each side of the fuel loading and ash removal opening. I[...]

Ussc 7 CLEARANCES TO COMBUSTIBLES It is of utmost importance that the clearances to combustible materials be strictly adhered to during installation of the stove. Refer to the tables below : Floor to ceiling height must be at least 7’ (84”) in all cases. The clearance between the flue pipe and a wall are valid only for verticle walls and for ve[...]

8 Ussc REDUCED CLEARANCES (CANADA ONLY) You may decrease the clearances by installing heat radiation shields between the walls or the ceiling and the stove. These heat radiation shields must be installed permanently, and can include sheet metal, a rigid non-combustible sheet or a masonry wall. Clearances of not less than 1" (25 mm) and not mor[...]

Ussc 9 CHIMNEY Your wood stove may be hooked up with a factory built or masonry chimney. If you are using a factory built chimney, it must comply with UL 103 or ULC S629 standards; therefore it must be a Type HT (2100°F). It is extremely important that it be installed according to the manufacturer's specifications. If you are using a masonry [...]

10 Ussc CHIMNEY CONNECTOR (STOVE PIPE) Your chimney connector and chimney must have the same diameter as the stove outlet. If this is not the case, we recommend you contact your dealer in order to insure there will be no problem with the draft. The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021" or 0[...]

Ussc 11 TYPICAL INSTALLATIONS FACTORY BUILT CHIMNEY : Wall Installation Vertical Installation[...]

12 Ussc TYPICAL INSTALLATIONS continued... MASONRY CHIMNEY :[...]

Ussc 13 TYPICAL INSTALLATIONS continued... FACTORY BUILT THIMBLE : BUILT THIMBLE :[...]

14 Ussc OUTSIDE COMBUSTION AIR Your Magnolia stove is approved to be installed with an outside air intake which is necessary for a mobile home. This type of installation is also required in air tight houses and houses with negative pressure problems. You can purchase this option through your Magnolia dealer. Make sure to specify this part number: #[...]

Ussc 15 TYPE WEIGHT PER CORD EFFICIENCY SPLITS MILLIONS (LBS. CU. FT., DRY) RANKING BTU's/CORD Hickory 63 4500 1.0 Well 31.5 White Oak 48 4100 .9 Fair 28.6 Red Oak 46 3900 .8 Fair 27.4 Beech 45 3800 .7 Hard 26.8 Sugar Maple 44 3700 .6 Fair 26.2 Black Oak 43 3700 .6 Fair 25.6 Ash 42 3600 .5 Well 25.0 Yellow Birch 40 3400 .4 Hard 23.8 Red Maple [...]

16 Ussc TESTING YOUR WOOD When the stove is thoroughly warmed, place one piece of split wood (about five inches in diameter) parallel to the door on the bed of red embers. Keep the air control full open by pulling on it and close the door. If ignition of the piece is accomplished within 90 seconds from the time if was placed in the stove, your wood[...]

Ussc 17 WARNINGS • NEVER OVERFIRE YOUR STOVE. IF ANY PART OF THE STOVE STARTS TO GLOW RED, OVER FIRING IS HAPPENING. READJUST THE AIR INTAKE CONTROL AT A LOWER SETTING. • THE INSTALLATION OF A LOG CRADLE IS NOT RECOMMENDED IN YOUR MAGNOLIA WOOD STOVE. • NEVER PUT WOOD ABOVE THE FIREBRICK LINING OF THE FIREBOX. RELOADING Once you have obtained[...]

18 Ussc ASH DISPOSAL Ashes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep. Always empty the stove when it is cold, such as in the morning. Always dispose of ashes in a metal container with a tight fitting lid. Place this container on a non combustible floor or on the ground, well away from all combustible ma[...]

Ussc 19 REPAIR PARTS 1 2 4 3 5 8 7 6 9 10 11 12 13 14 15 KEY DESCRIPTION PART NO. QTY 1 Flue Collar 25269B 1 2 Feed Door 25266 1 3 Door Handle 25097B 1 4 Door Handle Pin 83506 1 5 Hinge Pin 83443 2 6 Magnolia Glass 891096 1 7 Bottom Glass Retainer 25270 1 8 Top Glass Retainer 25178 1 9 Heat Shield Deflector 25265B 1 10 Blower Back 25089B 1 1 1 Blow[...]

20 Ussc THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM YOUR MAGNOLIA HEATER, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE. WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON THE NAMEPLATE ATTACHED TO THE HEATER. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWI[...]