Tripp Lite EMS Series инструкция обслуживания

Owner’ s Man ual Reliable Mobile EMS P ower Congratulations! Y ou’ve purchased the most advanced, feature-rich Inverter/Charger designed as an uninterruptible power source for medical equipment in ambulance/EMS vehicles. While ambulance/EMS vehicles are on a call, T ripp Lite EMS Inverter/Chargers keep critical equip- ment constantly in service[...]

2E Impor tant Safety Instructions SA VE THESE INSTR UCTIONS! This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all T ripp Lite Inverter/Chargers. Location W arnings • Install your Inverter/Charger (whether for a mobile or stationary application) in a location or comp[...]

3E Feature Identification Configuration DIP Switches: optimize Inverter/Charger operation depending on your application. See pages 5-6 for setting instructions. Operating Mode Switch: controls Inverter/Charger operation. The “AUTO/REMOTE” setting ensures your equipment receives constant, uninterrupted AC power . It also enables the Inverter/Cha[...]

Switch Modes After configuring, mounting and connecting your Inverter/Charger , you are able to operate it by switching between the following oper- ating modes as appropriate to your situation: AUTO/REMOTE: Switch to this mode when you need constant, uninterrupted AC power for connected equipment. The Inverter/Char ger will continue to supply AC po[...]

5E Configuration Select Battery T ype—REQUIRED CAUTION: The Battery T ype DIP Switch setting must match the type of batteries you connect, or your batteries may be degraded or damaged over an extended period of time. See “Battery Selection,” p. 7 for mor e information. Battery T ype Switch Position Gel Cell (Sealed) Battery Up W et Cell (V en[...]

6E Configuration (Continued) Set Battery Charging Amps—OPTIONAL Check specifications for your unit’ s high- and low-charging amp options. By setting on high charging, your batteries will char ge at maxi- mum speed. When setting on low char ging, you lengthen the life of your batteries (especially smaller ones). Battery Charger Switch Position L[...]

7E Battery Selection Example 75 DC Amps × 5 Hrs. Runtime × 1.2 Inefficiency Rating = 450 Amp-Hour s Select A uxiliary Battery T ype (if an y) Select “Deep Cycle” batteries to receive optimum performance from your Inverter/Charger . Batteries of either W et-Cell (vented) or Gel-Cell /Absorbed Glass Mat (sealed) construction are ideal. 6-volt ?[...]

Mounting W ARNING! Mount y our In ver ter/Charger BEFORE DC batter y and A C power connection. Failure to f ollow these instructions ma y lead to per sonal injury and/or damage to the In ver ter/Charger and connected systems. T ripp Lite manufactures a variety of different Inverter/Char gers with a variety of different mounting options for use in v[...]

9E • Connect DC W iring: Though your Inverter/Charger is a high-ef ficiency con- verter of electricity , its rated output capacity is limited by the length and gauge of the cabling running from the battery to the unit. Use the shortest length and largest diameter cabling (maximum 2/0 gauge) to fit your Inverter/ Charger's DC input terminals.[...]

Gr ound* • Connect the incoming and outgoing ground wires to the GROUND (green) terminal . AC Input • Connect the incoming hot wire to the input hot (brown) terminal . • Connect the incoming neutral wire to the input neutral (blue) terminal . AC Output • Connect the outgoing hot wire to the output hot (black) terminal . • Connect the outg[...]

11E Service Maintenance Before returning your Inverter/Charger for service, follow these steps: 1.) Review the installation and operation instructions to ensure that the service problem does not originate from a misreading of the instructions. Also, check that the circuit breaker(s) are not t ripped.* 2.) If the problem continues, do not contact or[...]

12E T ry these remedies for common Inverter/Charger problems before calling for assistance. Call T ripp Lite Customer Service at (773 ) 869-1234 before returning your unit for service. T roub leshooting SYMPT OM PROBLEMS CORRECTIONS No AC Output Unit is not properly connected to utility power Connect unit to utility power . (All Indicator Lights Ar[...]

Specifications MODEL NUMBER: EMS1012UL EMS1250UL EMS2012UL Series Number : AGAP100012MV3 AGAP5094 AGAP200012MV3 AC Input Connection: Input Cord Input Cord Hardwire INVERTER Common Specifications for All Models • DC Input V olts (Nominal): 12 VDC • DC Input V oltage Range: 10 - 15 VDC • Output V olts (Nominal): 120 V AC, ± 5% • Output F req[...]