Tripp Lite 220/230/240V AC / 12W инструкция обслуживания

Español / Français / Deutsche / Ðóññêèé Owner’ s Man ual 1111 W. 35th Street • Chicago, IL 60609 USA (773) 869-1234 • www .tripplite.com Copyright ©2004 T ripp Lite. All rights reserved. SmartOnline™ is a trademark of Tripp Lite. Smar tOnline ™ 3-Phase 10kV A Intellig ent T rue On-Line UPS System (T o wer) Input (V oltage/Phase)[...]

2 Impor tant Safety W arnings SA VE THESE INSTRUCTIONS. This manual contains important instructions and warnings that should be followed during the installation and maintenance of all T ripp Lite SmartOnline 3-Phase UPS Systems and their batteries. UPS Location W arnings • Install your UPS indoors, away from heat, direct sunlight, dust, and exces[...]

3 Contr ol P anel There are two separate UPS system modules: a power module and a battery module. Familiarize yourself with the location and function of the features on each module before installing and operating your UPS system. The power module is the only module which includes front panel features. FRONT P ANEL 1. "ON/OFF" Switch: This[...]

4 Rear P anels 17 18 Battery Module Rear Panel P ower Module Rear P anel 13 7 6 8 15 4 12 2 14 9 10 5 1 11 3 16 REFER TO USER'S MANU AL FOR TORQUING SPECIFICA TIONS, USE COPPER CONDUCTORS ONL Y . UTILISER SEULEMENT LES CONDUCTEURS DE CUIVRE. 1. Manual Bypass Switch: This switch is used in one step of putting the UPS in "MANUAL BYP ASS” [...]

5 Rear P anels (continued) 10. “Battery S tart” Switch: This momentary rocker switch allows you to “cold-start” your UPS and use it as a stand-alone power source when utility-supplied AC power is not present. The switch enables the UPS’ s DC/AC Inverter . Before “cold-starting” your UPS, make sure your power module and external batter[...]

6 Installation (continued) Operational Mode Selection (DIP Switch #4) The "On-Line" Mode provides on-line operation with zero transfer time. The "Economy" Mode provides line-interactive operation for increased efficiency when on-line protection is unnecessary , thus reducing operating costs without af fecting your UPS's out[...]

7 Installation (continued) EXTERNAL B A TTER Y MODULE CONNECTION (required) Connect the battery module to the power module. Consult the owner's man- ual that came with your battery module. Fully insert the connector on the end of the battery module's cable into the connector on the rear panel of the power module. Small sparks may occur; t[...]

8 Operation (Normal Conditions) TURNING THE UPS ON • Make sure the UPS is properly installed (see Installation section) and the Manual Bypass Key is set to NORMAL. • T urn the AC Input and Bypass AC Input Circuit Breakers ON. • If your AC input is providing power normally within your selected range (see Input V oltage Selection, and Specifica[...]

9 Operation (Normal Conditions) (continued) SELF-TESTING When you turn the UPS ON, it will perform a brief (about 25 second) self-test. See figure below for display sequence.* *Note: If starting from battery , the BA TTER Y LED will be lit and the I/P and BYP ASS LEDs will not. The final LCD display in the diagram below appears when the UPS is oper[...]

ON INVERTER LOAD = XXX% X.XXKW ON INVERTER IN R = XXXV XX.XHz ON INVERTER OUT = XXXV XX.XHz ON INVERTER BATT = XXXV XXX% PRESS SELECT KEY PRESS SELECT KEY PRESS SELECT KEY PRESS SELECT KEY ON INVERTER IN S = XXXV T=XXXV PRESS SELECT KEY ON BATTERY LOAD = XXX% X.XXKW ON BATTERY IN R = XXXV XX.XHz ON BATTERY OUT = XXXV XX.XHz ON BATTERY BATT = XXXV X[...]

11 Operation (Special Conditions) (continued) OPERA TION ON O VERLO AD When the UPS detects an output overload, it will commence a countdown (the length of time depending on the severity of the overload). If the UPS is still overloaded at the end of the countdown, the UPS will automatically shut down and go into Bypass Mode. Overload Condition LCD [...]

12 OPERA TION OF MANU AL BYP ASS SWITCH T urn this switch to “BYP ASS” before performing any maintenance on the UPS with the connected load supported. Connected equipmen t will receive filtered AC mains power, but will not receive battery power in the event of a blackout. SWITCHING UPS T O “BYP ASS” MODE • T urn the “ON/OFF” Switch OF[...]

13 Comm unications (continued) AS-400 INTERF A CE This female DB9 port connects your UPS to an IBM AS-400 computer via the included AS-400 cable. The port uses AS-400 communications to report UPS status. It can be used to allow an AS-400 to automatically save open files and shut down its operat- ing system during a blackout. AS-400 protocol include[...]

14 Comm unications (continued) REMO TE EMERGENCY PO WER OFF (EPO) This optional feature is only for those applications which require connection to a facility's Emergency Power Of f (EPO)circuit. When the power module is connected to this circuit, it enables emergency shutdown of the output. Using the included cable, connect the p ower mod- ule[...]

15 The specifications listed below are for T ripp Lite model SU10K3/1X which includes two modules: a power module and a battery mod - ule. The two modules are also sold separately with their own individual model numbers: power module (individual model #: SU10K3/1INTPM) and battery module (individual model #: BP240V10R T3U). Model: SU10K3/1X Include[...]

1111 W . 35th Street, Chicago, IL 60609 USA 773.869.1234 (USA) • 773.869.1212 (International) www .tripplite.com 2009XXXXX 93-2228_EN[...]