Texas Instruments TSC2007EVM-PDK инструкция обслуживания

User's Guide SLAU199 – March 2007 TSC2007EVM and TSC2007EVM-PDK User's Guide This user's guide describes the characteristics, operation, and use of the TSC2007EVM, both by itself and as part of the TSC2007EVM-PDK. This evaluation module (EVM) is a 4-wire touch screen controller EVM which also has auxiliary input and temperature mea[...]

www.ti.com 1 EVM Overview 1.1 Features 1.2 Introduction 2 Analog Interface EVM Overview • Full-featured evaluation board for the TSC2007 4-wire resistive touch screen controller (TSC). • Modular design for use with a variety of DSP and microcontroller interface boards. The TSC2007EVM-PDK is a complete evaluation kit, which includes a USB-based [...]

www.ti.com 3 Digital Interface 4 Power Supplies 4.1 TSC Power Digital Interface The TSC2007EVM is designed to easily interface with multiple control platforms. Samtec part numbers SSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P provide a convenient 10-pin, dual-row header/socket combination at J2. This header/socket provides access to the digital control[...]

www.ti.com 4.2 Stand-Alone Operation 4.3 USB-MODEVM Interface Power 5 EVM Operation 5.1 Analog Input 5.2 Digital Control 5.3 Default Jumper Locations EVM Operation When used as a stand-alone EVM, power can be applied to TP1, referenced to TP3. CAUTION Verify that all power supplies are within the safe operating limits shown on the TSC2007 data shee[...]

www.ti.com 6 Kit Operation 6.1 TSC2007EVM-PDK Block Diagram Kit Operation Table 6. List of Jumpers JUMPER SHUNT POSITION JUMPER DESCRIPTION JMP1 2-3 Analog power select (default is +3.3VD) JMP2 Closed EEPROM address select. When installed and used with the USB-MODEVM, firmware for the motherboard is executed from the EEPROM on the TSC2007EVM. This [...]

www.ti.com T A S 1 0 2 0 B U S B 8 052 m i cr o co n tr o lle r USB EVM Position 1 EVM Position 2 Control Interface Audio Interface TSC2007EVM T S C 2 0 0 7 SPI, I 2C I2S, AC97 X+ X− Y+ Y− AUX SDA SCL PENIRQ 6.2 Quick Start Kit Operation Figure 1. TSC2007EVM-PDK Block Diagram The USB-MODEVM interface board is intended to be used in USB mode, wh[...]

www.ti.com Kit Operation Place the CD-ROM into your PC CD-ROM drive. Locate the Setup program on the disk, and run it. The Setup program will install the TSC2007 Evaluation software on your PC. Accept the license agreement, and continue the installation. When the installation completes, click Finish on the TSC2007EVM installer window. You may be pr[...]

www.ti.com 6.3 USB-MODEVM Interface Board 6.4 Program Description 6.4.1 Touch Screen Functions Panel 6.4.2 Data Acquisition Functions Panel 6.4.3 Configuration Panel Kit Operation The simple diagram shown in Figure 1 shows only the basic features of the USB-MODEVM interface board. The board is built around a TAS1020B streaming audio USB controller [...]

www.ti.com 6.4.4 Datalogging 7 EVM Bill of Materials EVM Bill of Materials The two power-down bits of the TSC2007 can be set from this panel as well. A brief description of the mode selected is shown on the screen when setting these bits; see Table 3 ( Command Byte Definitions ) of the TSC2007 data sheet ( SBAS405 ) for details on what these bits d[...]

www.ti.com EVM Bill of Materials Table 8. USB-MODEVM Bill of Materials Reference Designator Description Manufacturer Manufacturer's Part Number R4 10 Ω 1/10W 5% Chip Resistor Panasonic ERJ-3GEYJ100V R10, R11 27.4 Ω 1/16W 1% Chip Resistor Panasonic ERJ-3EKF27R4V R20 75 Ω 1/4W 1% Chip Resistor Panasonic ERJ-14NF75R0U R19 220 Ω 1/10W 5% C[...]

www.ti.com 8 TSC2007EVM Schematic 9 USB-MODEVM Schematic TSC2007EVM Schematic Table 8. USB-MODEVM Bill of Materials (continued) Reference Designator Description Manufacturer Manufacturer's Part Number TP1, TP2, TP3, TP4, TP5, Miniature test point terminal Keystone Electronics 5000 TP6, TP9, TP10, TP11 TP7, TP8 Multipurpose test point Keystone [...]

1 2 3 4 5 6 A B C D 6 5 4 3 2 1 D C B A ti 12500 T.I. Boul e va r d , Da llas, Tex a s 75243 USA TITL E SHEET OF FILE SIZE DATE REV 5-Jan-2007 DRAWN BY ENGINEER REVISION H IST ORY REV ENGINEERING CHANG E NUMBER APPROVED B DATA ACQUISITION PRODUCT S HIGH-PER FORMANCE AN ALOG DIVISION SEMICONDUCTOR GROUP WENDY FANG STEVE LEGGIO A 11 TS C2007EVM DOCUM[...]

1 2 3 4 5 6 A B C D 6 5 4 3 2 1 D C B A ti 6730 SOUTH TUCSON BLVD., TUCSON, AZ 85706 USA TITLE SHEET OF FILE SIZE DATE REV 10-Jun-2004 DRAWN BY ENGINEER REVISION HISTORY REV ENGINEERING CHANGE NUMBER APPROVED B DATA ACQUISITION PRODUCTS HIGH PERFORMANCE ANALOG DIVISION SEMICONDUCTOR GROUP RICK DOWNS ROBERT BENJAMIN G:USB Motherboard - Modular Evm[...]

1 2 3 4 5 6 A B C D 6 5 4 3 2 1 D C B A ti 6730 SOUTH TUCSON BLVD., TUCSON, AZ 85706 USA TITLE SHEET OF FILE SIZE DATE REV 10-Jun-2004 DRAWN BY ENGINEER REVISION HISTORY REV ENGINEERING CHANGE NUMBER APPROVED B DATA ACQUISITION PRODUCTS HIGH-PERFORMANCE ANALOG DIVISION SEMICONDUCTOR GROUP RICK DOWNS ROBERT BENJAMIN G:USB Motherboard - Modular Evm[...]

EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling th[...]

IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders[...]