Texas Instruments DW30 инструкция обслуживания

D S + 6 0 / D W 3 0 / M a t r i x 3 0 0 0 U s e r ’ s M a n u a l 013-100149-02[...]

DS+ 60 / DW 30 / Matrix 3000 User’s Manual Table of Contents 013-100149-02 Rev. 1 (01 /07) Software v1.2 and later Christie DS+60/DW30/Matrix 3000 User’s Manual NOTE: Due to continuing research, all information in this manual is subject to change without notice. 1.1 Projector Overview ............................................................[...]

[...]

Section 1 Introduction 013-100149-02 Rev. 1 ( 01/07) Christie DS+60/ DW30/Matrix 3000 User’s Manual 1-1 Christie DS+60/DW30/Matrix 3000 projectors are professional quality single-chip projectors that use Digital Light Processing ™ (DLP ™ ) technology from Texas Instruments to achieve bright, crisp images. With a range of available lenses, inp[...]

Section 1: Introduction 1-2 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) 1 Powering ON (a) Be patient when powering the projector ON or switching lamp operation modes. As the lamps warm up, brightness will gradually increase. (No light appears on the wall during the first 25 seconds.) On the rare occurrence a lamp d[...]

Section 1: Introduction 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 1-3 The light generated by the lamp(s) is then sequentially filtered into the RGB color primaries by the spinning color wheel(s ) and presented to the single chip DMD, located in the light engine, in sequence. The reflected light from the DMD chip[...]

Section 1: Introduction 1-4 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) Whether the projector is under warranty or the warranty has expired, Christie’s highly trained and extensive factory and dealer service network is always available to quickly diagnose and correct projector malfunc tions. Service manuals and u[...]

Section 2 Installation & Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+ 60/DW30Matrix 3000 User’s Manual 2-1 The instructions provided here are for tho se that are familiar with the projector and wish to quickly set it up and use it temporarily. Refer to the remaining subsections of this manual for a more complete setup. Install a Projectio[...]

Section 2: Installation and Setup 2-2 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) Connect the Line Cord The North American-rated line cord is provided with each projector. Ensure that you are using a line cord, socket an d power plug that meets the appropriate local rating standards. Connect the appropriately rated[...]

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 2-3 Proper installation of your projector will ensu re the quality of your display. Whether you are installing a projector temporarily or permanentl y you should take the following into account to ensure your projector performs optim all[...]

Section 2: Installation and Setup 2-4 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) Rear screen installations There are two basic types of rear screens : diffused and optical. A diffused screen has a surface, which spread s the light striking it. Purely diffused screens have a gain of less than one. The main advantag[...]

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 2-5 The high brightness of this projector is well suited for locations where ambient lighting might be considered less than ideal for projection. A typical room with ceiling lights and windows rarely requires special attention. Contrast [...]

Section 2: Installation and Setup 2-6 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) Figure 2.1. Estimating Throw Distance Vertical and horizontal position The correct vertical and horizontal position of the projector in relation to the screen depends on the lens type and the screen size. Ideally, the projector should[...]

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 2-7 Table 2. 2 Lens Offsets for DW30 (720P) %P i x e l s %P i x e l s %P i x e l s %P i x e l s 0.8:1 fixed 81% + / -292 90% + / -652 31% + / -200 6 6% + / -840 1.2:1 fixed 231% + / -832 11 0% + / -1192 104 % + / -664 102% + / -1304 1.3-[...]

Section 2: Installation and Setup 2-8 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) Figure 2.3. Lens Vertical Offsets The horizontal position of the image can be offset – t hat is moved to the left or right of lens center, by adjusting the fully mo torized lens mount through software. The amount of horizontal offse[...]

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 2-9 Figure 2.4. Examples of Horizontal Offset[...]

Section 2: Installation and Setup 2-10 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Figure 2.5. Lens Horizontal Offsets Lifting and transporting the projector – The projector is light enough to lift and transport a short distance. Use the indentations on the bottom of the projector as a guide for hand placement, [...]

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 2-11 Figure 2.6. Adjusting projector height You can modify the height of the projector to remedy a slightly uneven mounting surface by adjusting the three feet threaded into the bottom chassis. Turn each foot clockwise or counter- clockw[...]

Section 2: Installation and Setup 2-12 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Sources connect to the Input Panel located at the back of the projector. See Figure 2.10. The upper right corner ( INPUT 1 ) typically accepts an RGB signal from an external analog RGB source, or it can also be used for YPbPr signal[...]

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 2-13 Figure 2.11. Connecting RGB and Sync NOTES: 1) If for some reason the projector fails to recognize a signal as an RGB signal, specify the Color Space option within the Image Settings menu. See 3.7, Adjusting the Image. 2) To connect[...]

Section 2: Installation and Setup 2-14 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) INPUT 3 and INPUT 4 provide simultaneous connection of both a com posite video source ( INPUT 3 ) and an S-Video source ( INPUT 4 ). See Figure 2.13. Figure 2.13.Connecting Composite or S-Video sources Use the DVI-I connector at INP[...]

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 2-15 As an alternative to the projector’s keypad or rem ote, you may wish to communicate with the projector using a PC or other controller. Such a device sends commands and receives feedback via serial links (RS232 and RS422), Ethernet[...]

Section 2: Installation and Setup 2-16 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Figure 2.15. Connecting RS422 Ethernet Communications To add the projector to an existing Ethernet network with other eq uipment such as controllers and other projectors, connect st andard CAT5 Ethernet cable between your Ethernet c[...]

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 2-17 Regardless of how it is assigned, once a projector has a valid and unique address it will respond to commands sent to this address. To determine the projector’s current IP address, consult the Status or Communications menus. Refer[...]

Section 2: Installation and Setup 2-18 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Note that communication parameters such as baud rate must be set to match the particular controlling device before connecting as a network—refer to the documentation that came with your controlli ng device in order to determine th[...]

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 2-19 NOTES: Only the port and IP address of the projector can be changed. The subnet mask is fixed (255.255.255.0). CHANGING THE PORT#: On some Ethernet networks, fi rewall restrictions may require that the port number of the projector b[...]

Section 2: Installation and Setup 2-20 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Plug the line cord to the AC receptacle locat ed on the right hand side of the projector and the three-pronged end into a grounded AC outlet ( Figure 2.22). The input voltage to the projector must be capable of 100 – 24 0 VAC. See[...]

Section 3 Operation 013-100149-02 Rev. 1 ( 01/07) Christie DS+60/ DW3K/Matrix 3000 User’s Manual 3-1 This section explains how to effectively operate the projector once it has been installed. It is recommended that you read this section and familiarize yourself with the components and the available menu options befor e you begin using your projec[...]

Section 3: Operation 3-2 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) (3) The AC receptacle is located on the right side of the projector (opposite side of lamp doors). Use this outlet to plug in an appropriately rated line cord. See 2.6 Power Connection for details. The input voltage to the projector m ust be capab[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-3 (6) & (11) The two IR sensors located on the projector receive transmissions from the IR remote from up to 100 feet away. It is im portant to keep the transmission path to these sensors unobstructed for uninterrupted communications with the p[...]

Section 3: Operation 3-4 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) The IR remote controls the projector by way of wireless communications from a battery-powered infrared (IR) transmitter. U se the IR remote the same way you would use a remote control supplied with a TV or VCR. When making key presses, direct the [...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-5 You can convert the IR remote into a wired IR remote using the cable provided wi th the projector. Connect one end into the rem o te and the other to the mini stereo connector on the input panel labeled REMOTE . The wired remote is recommended wh[...]

Section 3: Operation 3-6 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) Table 3.1. Auto Setup What an “Auto Setup” Does OPTIMIZES: SETS TO DEFAULT: Pixel Tracking Contrast Pixel Phase Brightness Size and Blanking Auto Input Level (off) Vertical Stretch Detail (if video source) Position Filter Input Levels Luma Del[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-7 Contrast Press Cont r ast to change the amount of white in your im ages. Use keys until you reach the desired level of contrast—for best results, start low and increase so that whites remain bright but are not distorted or tinted, and that ligh[...]

Section 3: Operation 3-8 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) Shutter Press and hold Shutter for two seconds to toggle the in ternal mechanical shutter blade closed or open with a single keystroke, or press and release Shutter followed immediately by (closed) or (open) to guarantee the correct toggle (useful[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-9 NOTES: 1) The "Broadcast Keys" option in the Communications menu must be selected for only one (any) projector in a serial network. The keypad in use must be OFF (disabled) for the remaining projectors. See also 3.6, Adjusting System Pa[...]

Section 3: Operation 3-10 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Laser Press to activate the laser p ointer on the remote. This feature is useful when making presentations - just point the remote at the screen to highlight an area of your presentation. Keep the key depressed while you are pointing. Release it[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-11 Figure 3.5. Context-sensitive Help From presentation level, press Help to access general Help Topics . Scroll as necessary within a topic. Press Help or Exit to return to your presentation. Figure 3.6. Accessing General Help Topics If a slidebar[...]

Section 3: Operation 3-12 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Once selected, change the setting as desired (see below) and press to save and return to the current function menu. Slidebars in menus – The current value for a given parameter, such as size or vertical stretch, a ppears to the left of its sli[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-13 If you prefer to quickly scroll through a list without first pulling it down, hi ghlight the option and use . Press when the desired choice appears. NOTES: 1) Press or to jump between pages in an extra long pull-down list. 2) Press Exit while in[...]

Section 3: Operation 3-14 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) NOTES: 1) Once you enter the first digit, this digit replaces all old digits. 2) If you press any non-numbered key, the number en tered up to that point is accepted and updated as the new value. 3) Press Exit to cancel editing of numerical value[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-15 Shown at right is a sample channel list as would be available from Cha nne l . This is typically called the channel list . NOTE: The Cha nne l key may display a channel list or not, depending on what you have defined for “Display Channel List?[...]

Section 3: Operation 3-16 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) All available channels are listed in the Channel Setup menu, which describes how each channel can be accessed and which ser ves as the gateway for editing, copying and deleting channels. From the presentation level press Men u to display the Mai[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-17 FUNCTIONS WITHIN THE CHANNEL SETUP MENU — To copy, delete or edit a channel, highlight the desired channel in the Channel Setup m enu and do one of two things: • Press Fun c if you want to copy the selected channel or delete this or other ch[...]

Section 3: Operation 3-18 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) TO DELETE MULTIPLE CHANNELS , highlight any channel in the Channel Setu p menu and press Fun c to go to the Channel Copy/Delete submenu. Select “Delete Unlocked Only” and press to delete all unlocked channels . Or select “Delete All Channe[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-19 • AUTO SOURCE: If checked, (default), the projector can automatically locate this channel when an incoming input signal ma tches. If not checked, th e projector can locate the selected channel only wh en it is directly selected via Channe l on[...]

Section 3: Operation 3-20 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) In the Size and Position menu, you can increase or decrease the size of your image, change its proportion (aspect ratio), move the image to a specific area of the screen, and refine other related parameters. Use Size and Position controls to ma [...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-21 • Select “NO RESIZING” to display the image in its native resolution, which may or may not match the projector’s resolution. For example, for a source with a native resolution of 800 x 600, “No Resizing” in an SXGA+ projector will us[...]

Section 3: Operation 3-22 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) • Select “ANAMORPHIC” to display an anamorphic image in its native 16:9 aspect ratio. The image will fill the screen from side-to-side and be centered between black bars at top and bottom. Size “Size” controls both the image width and [...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-23 H-Position This option moves the image right or left within the a rea of available pixels. NOTE: The value shown represents where the approximate center of the image lies in relation to the total number of pixels ava ilable horizontally. This va[...]

Section 3: Operation 3-24 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) PLUG & DISPLAY (EDID): By default, a Plug & Play (EDID) source outputs a signal according to the EDID information provided by the projector. To override this information and display in a different format (for exam pl e, if your Plug &[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-25 Brightness ( SHORT CUT: Press Bri ght an d adjust the slidebar.) “Brightness” increases or decreases the amount of black in the image (0-100). For best results, keep close to 50. Start with a high value and decrease so that dark areas do not[...]

Section 3: Operation 3-26 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Noise Reduction “Noise Reduction” is similar to the “Filter” control, but operates in the post-sampling digital domain with a more subtle effect. Higher settings are most useful for clearing up noisy RGB images such as those from a PC . [...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-27 VIDEO STANDARD: For all but the more unusual video standards available in the world, the projector automatically detects the incoming horizontal and vertical frequencies and sets the projector’s processing of this signal to the corresponding s[...]

Section 3: Operation 3-28 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) DECODER LUMA DELAY – This control affects any incoming composite or S-video signal, delaying the luma signal (intensity) in relation to the chrom a (color). In the image, increasing the luma delay will move lum a (seen as a shadow where colors[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-29 then delete the checkmark and exit. The Auto Input Level is automatically turned off upon exiting the Input Levels menu. BLACKLEVELS AND DRIVES – To check your im age levels and adjust these controls: 1. Make sure overall “Contrast” and ?[...]

Section 3: Operation 3-30 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) black and white are known to be at opposite edges of the image, you can watch these isolated areas while adjusting individual blacklevels and input drives until both black and white edges are just visible and distinguished from neighboring pixel[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-31 Advanced Image Settings — SUBMENU Use the Advanced Image Settings submenu to make the adjustments necessary for lesser-used but more specialized applications on your projector. GAMMA TABLE: This control applies a default video , graphics or si[...]

Section 3: Operation 3-32 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Adjustment” options or color temperatures su it your application, select one of four color gamuts previously defined by a user (User 1, 2, 3, 4). A “User” option applies a customized color performance in which the u ser has precisely set t[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-33 Simulation 3D — SUBMENU OF ADVANCED IMAGE SETTINGS This submenu allows you to adjust the timing between the input signal and its appearance on screen. This is most useful in applications where you want to match the timing of the projector to o[...]

Section 3: Operation 3-34 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) DETAIL THRESHOLD — Use “Detail Threshold” to define at what frequency level the “Detail” control will begin to magnify high frequencies, which adds details back into the image. Raise the threshold to ignore more of these high frequenci[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-35 Menu Prefe rences — SUBMENU Adjust the appearance, content and/or location of on-screen menus and messages. LARGE MENU FONT — Enter a checkmark to enlarge menus and their text. You may have to adjust “Menu Location” to accommodate the in[...]

Section 3: Operation 3-36 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) • Startup And No Signal – A splash screen appears at startup only if there is no source signal. To replace the default “Christie logo” splash screen (or other) with one of your own, use KoRE Librarian to download the desired .bmp to the [...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-37 Figure 3.17. Using the “Network Routing” Option RS232 AND RS422 JOINED: Messages originating from an RS232 or RS422 controller will be relayed to all RS232or RS422 ports. Any Ethernet communication, however, will not. RS232 AND ETHERNET JOIN[...]

Section 3: Operation 3-38 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) by a DHCP server or other user. It takes approximately 10 seconds for the projector to respond at its new address. PORT: On some Ethernet networks, firewall r estrictions may require that the port number of the projector be changed from its defa[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-39 * Functions are only active when th e Slider Lock is set to Unlocked NOTE: It is important to ensure the channels DO NOT overlap another device. Example: Good Bad Proj1_Base = 0 Proj1_Base = 5 Proj2_Base = 10 Proj2_Base = 9 Proj3_Base = 20 Proj3[...]

Section 3: Operation 3-40 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) To disable both IR sensors, you cannot use the IR remote keypad to select the second OFF setting. This safeguard prevents accidentally disabling an IR keypad while you are using it. Instead, use either the built-in ke ypad or a wired rem ote (op[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-41 memory, typically creating one or more “squeezed” or stretched areas in the display. If no custom warps have been created, the User options will have no effect. 2D KEYSTONE: Move one or more corner points as desired for your application. Tra[...]

Section 3: Operation 3-42 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Use to correct a keystoned image shape in which both sides of the image are inclined toward the top or bottom edge. Keystone is typically caused by tilting the projector in relation to the screen so that the lens su rface and screen are no longe[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-43 From the factory, the projector can utilize any of the 3 pre-defined color performance settings identified at right (default=Max Drives), or colors can be driven on the basis of color temperature. For most applications, one of these gamuts will [...]

Section 3: Operation 3-44 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) four “User” color gamuts needed for your e nvironment and applications. Apply at any time in the Advanced Image Settings menu. Figure 3.21. CIE 1931 Chromaticity Diagram NOTE: Keep new x,y coordinates within the original color gamut triangle[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-45 Test Pattern Choose the desired internal test pattern to display, or select OFF to turn off a test pattern. Alternatively, use the Te s t key for cycling through test patterns. NOTE: There is a center line (both horizontal and vertical) in the E[...]

Section 3: Operation 3-46 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Two sets of values are automatically saved with these controls—one value for Input #1, and one for Input #2 (a nalog). The curre nt set of values depends on which source is in use. This enables a source to be processed correctly via 2 differen[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-47 Peak Detector The “Peak Detector” is a fast method for defining individual in put levels, and can improve the accuracy of input levels set by the Auto Input Level function. Enabling the “Peak Detector” activates a special operating mode [...]

Section 3: Operation 3-48 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) PIP (Picture-in-Picture) and Seamless Switc hing are independent but related projector features that both utilize two image processi ng paths within the projector. In the case of Picture-in-Picture, this double processing enables you to displa y[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-49 Swap Main and PIP Image Toggle the current picture-in-picture relati onship so that the primary (main) image becomes secondary (PIP), and the secondary image becomes primary. Swapping is available only when PIP is enabled. NOTE: There may be a s[...]

Section 3: Operation 3-50 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) PIP Border Width Set the desired line thickness for your PIP window border. PIP Border Color Select the desired color for the PIP window border. NOTES: 1) Numbers 7 and 8 on the Pictu re-in-Picture and Switching submenu control switching paramet[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-51 Numbers Select Main Image Use Numbers Select Main Image to use the numeric keys #1-8 as input keys. This remapping of the keypad (see right) can be particularly useful with PIP displays, providing a convenient shortcut for changing the primary ([...]

Section 3: Operation 3-52 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) • In Single Lamp mode , the projector will try to strike the lamp again in 90 seconds (considered re-strike #1). Only after the third attempt (re-strike #2) will the projector declare the lamp as “Failed to Strike” (in Lamp submenu) and au[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-53 Figure 3.24. The Lamp Menu LAMP MESSAGE - Enter a checkmark to enable a warning message that will appear upon power-up when the lamp has reached the specified lamp limit and should be replaced. Delete the checkmark to prevent display of this mes[...]

Section 3: Operation 3-54 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) NOTES: 1) The projector will automatically shutdown if it detects both lamps have “failed” (this includes lamps not installed). 2) The lamp ope ration mode will not automatically switch to a previous mode once a “failed” lamp is replaced[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-55 The read-only Status menu lists a variety of details about t h e standard and optional components currently detected in the projector. Refer to the Status menu for versions of hardware and software installed, the t ype (size) of lamp, the hours [...]

Section 3: Operation 3-56 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Color Adjustment Procedur e Once the Color Primary Settings are calibrated for the site (see above), use the Color Adjustments by X,Y or Color Saturation menu to further refine each projector’s fundamental colors so that the hue and inte nsity[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-57 Figure 3.26. Copy X/Y Values into All Projectors 6. In each projector, judge by eye and adjust x/y coordinates slightly in the following manner:  To match reds, decrease “Red X” until full field red screens match.  To match greens, dec[...]

Section 3: Operation 3-58 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) 7. All screens should now be color-matched and the will remain matched upon exit from the menus. Apply this new “User” gamut to a source at any time by selecting it in the “Select Color Adju stment” list accessed in the Advanced Image Se[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-59  ADJUST COLORS FIRST— Always adjust the primary colors as described in the “ Matching Colors in Multiple Screens ” procedure (above) before attempting to work with Brightness Uniformity. This ensures that primary colors, color temperatu[...]

Section 3: Operation 3-60 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) 1c) Select the 13 Point test pattern for display. This pattern provides 9 screen “zones” with 13 targets. FOR BEST RESULTS: Rather than examining the CENTER of each zone when assessing Brightness Uniformity adjustments, focus on extreme EDGE[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-61 blue, too re d or too green, g o to the Left Uniform ity m enu and adjust the colors (i.e., chan ge their light output) until all portions of the left side closely match the center color temperature. Ad just an edge fi rst (focusing on its cente[...]

Section 3: Operation 3-62 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) Step 4: Readjust Color Temperature (lev el of red/green/blue) in 8 Zo nes 4a) Return to Steps 2a & 2b and, if necessary, fine tune the zones so that they all still exhibit a single color temperature. Canceling Brightness Uniformity If you do[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-63 Main Functions Use standard edge blending controls to set the precise width , shape and midpoint yo u need to blend overlapping edges together smoothl y .  Blend Width determines how much area is used for bl ending along an overlapping edge. [...]

Section 3: Operation 3-64 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07)  Show Blending Overlap turns your defined blend width area to solid gray so that two adjacent images can be seamlessly aligned simply by overlapping their gray bars, if needed. Toggle the Show Blending Overlap off to reactivate the blend effe[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-65 3. SET STARTING POINTS FOR ADJUSTMENT :  Set all blend widths to 0.  Go to “More” and set everything in the Edge Blending (2) menu to 50. Figure 3.35. Set Starting Points for Each Project or 4. SET BLEND WIDTH : On one projector, incre[...]

Section 3: Operation 3-66 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) VIA ASCII MESSAGING — Connect a serial link between your contr oller and the RS232 or RS422 port (recommended), or open an Ethernet socket (i.e., Telnet) between your controller and the valid projector addr ess. Valid ASCII codes and messages [...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-67 Invalid User Entry A keypad entry not recognized by the projector triggers a short on-screen error message identifying the problem. For example, if you specify a channel number that is not available, the message “ Invalid Channel will appear. [...]

Section 3: Operation 3-68 Christie DS+60/DW30/Matrix 3000 U ser’s Manual 013-100149-02 Rev. 1 (01 /07) should be reported to the manufacturer. You can press Exit Exit to remove the message, but for best results you should reset the projector—power the projector down and up again with the (power) key. System Errors A system error message indicat[...]

Section 3: Operation 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 3-69 Code Description GENERAL 12 Sof tware bug. Contact dealer/fa ctory. 13 Fla sh memory corrupted. Downloa d new softwa re. 14 E ngineering o nly program ming is com plete. Call Christie, re place TIPM. 15 Attempting to downlo ad code without being[...]

[...]

Section 4 Maintenance 013-100149-02 Rev. 1 ( 01/07) Christie DS+60/ DW3K/Matrix 3000 User’s Manual 4-1 The projector is an international regulatory agency approved product designed for safe and reliable operation. It is important to acknowledge the following precautions while operating the projector to assure complete safety at all times. WARNING[...]

Section 4: Maintenance 4-2 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) Operate the projector in an environment, which meets the operating range as specified in Section 6 – Specifications. • Do not operate the projector close to wate r, such as near a swimming pool. Do not operate in extremely humid environments[...]

Section 4: Maintenance 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 4-3 • The projector is equipped with a thr ee-wire plug having a third groundi ng pin. This is a safety feature – if you are unable to insert the plug into an outlet contact an electrician to have the outlet replaced. Do not defeat the safety p[...]

Section 4: Maintenance 4-4 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) WARNING Always power do wn and unplug th e projector before cleaning or servicing. Table 4.1. Maintenance Guide Part Description Frequency How to clean Lens As required Clean the lens only when absolutely necessary. A s mall am ount of dust on t[...]

Section 4: Maintenance 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 4-5 The optional IR remote uses two AA size, 1.5V alkaline batteries. To replace the batteries simply turn the remote over and push out the cover using the finger groove, as shown in (1) Figure 4.1. Remove and properly discard the old batteries. In[...]

Section 4: Maintenance 4-6 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) To replace a lamp: 1. Press to power down the projector and allow the lamp to cool for approximately 5 minutes after the fans have turned of f before continuing with Step 2. If required, you can switch lamp modes and cut power to the lamp you wa[...]

Section 4: Maintenance 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 4-7 Figure 4.4. 6. Discard the lamp using approved disposal methods for your area. NOTE: Lamps containing mercury must be treated as hazardous waste if discarded in large volumes. WARNING Do not stick hands into an empty lamp co mpartment, especial[...]

Section 4: Maintenance 4-8 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01 /07) Use the following instructions when replacing a projection lens: NOTE FOR FIRST TIME USE: The projection lens is shipped separately from the projector. Before you install a lens it is important to remove the lens plug from the lens opening in th[...]

Section 5 Troubleshooting 013-100149-02 Rev. 1 ( 01/07) Christie DS+60/ Dw3K/Marix 3000 User’s Manual 5-1 If the projector does not appear to be operating properly , note the symptoms present and use the following guide to assist you. If you cannot resolve the problems y ourself, contact your dealer for assistance. NOTE: A qualified service techn[...]

Section 5: Troubleshooting 5-2 Christie DS+60/DW3K/Matrix 3000 User ’s Manual 013-100149-02 Rev. 1 ( 01/07) The display is faint… 1. Brightness and/or contrast may be set very low. 2. The source may be double terminated. Ensu re the source is ter minated only once. 3. The source (if non-video) may need a different sync tip clamp location. The u[...]

Section 5: Troubleshooting 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 5-3 2. The video input may not be term inated. Ma ke sure the video input is terminated (75 Ω ). If it is the last connection in a loop-through c h ain, the video input should be terminated at the last source input only. 3. The input signal an[...]

[...]

Section 6 Specifications 013-100149-02 Rev. 1 ( 01/07) Christie DS+60/ DW30/Matrix 3000 User’s Manual 6-1 NOTES: 1) Due to continuing research, specifica tion s ar e su bject to change withou t notice. 2 ) Specifications apply to a ll models unless otherwise noted. Resolution SXGA+ (1400 x 1050) for DS+ 60 and Matrix 3000 720P (1280 x 720, widesc[...]

Section 6: Specifications 6-2 Christie DS+60/DW30/Matrix 3000 User ’s Manual 013-100149-02 Rev. 1 ( 01/07) * for DS+60 and Matrix 3000 , 0% offset is equal to half the image above and below lens center (5 25 pixels) OR half the im age to the left or right of lens center (700 pixe ls) – see tab le below. Table5.1. SXGA+ Lens Offsets % Pixels % P[...]

Section 6: Specifications 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 6-3 Composite Video and S-Video Signal Formats Composite-video (CVBS), S-video Y/C) Video Standards NTSC, NTSC 4.43, PAL, PAL M, PAL N, PAL60, SECAM Input Levels Composite-video: 1.0Vp-p ± 3db (including sync tip) S-video luma (Y): 1.0Vp-p ± 3[...]

Section 6: Specifications 6-4 Christie DS+60/DW30/Matrix 3000 User ’s Manual 013-100149-02 Rev. 1 ( 01/07) General Voltage Range 100 – 240 VAC nominal Line Frequency 50 Hz – 60 Hz nominal Max. Inrush Current 68 A Current Rating Both lamps on - 8.4A @ 100V (typical), 3.5A @ 240V (typical) One lamp on - 4.8A @ 100V (typical), 2.0A @ 240V (typic[...]

Section 6: Specifications 013-100149-02 Rev. 1 (01 /07) Christie DS+60/DW 30/Matrix 3000 User’s Manual 6-5 Temperature 10 ° C to 35 ° C Humidity 20% to 90% Altitude 0m to 3050m Temperature -20 ° C to 70 ° C Humidity 5% to 95% Altitude 0m to 9144 m IR remote (with batteries) Wired remote control cable Line Cords (North American and European) C[...]

[...]

Appendix A Glossary 013-100149-02 Rev. 1 ( 01/07) Christie DS+60/ DW30/Matrix 3000 User’s Manual A-1 This appendix defines the specific terms used in this manua l as they apply to this projector. Also included are other general terms commonly used in the projection industry. The time, inside one horizontal scan lin e, during which video is genera[...]

Appendix A: Glossary A-2 Christie DS+60/DW30/Matrix 3000 User ’s Manual 013-100149-02 Rev. 1 ( 01/07) A number that uniquely identifies a specific channel retained in projector memory. The projector can retain up to 50 channels. A menu item that indicates whether an option is currently in effect (checked) or not (unchecked). The signal representi[...]

Appendix A: Glossary Christie DS+60/DW30/Matrix 3000 User’s Manual A-3 A type of rear-projection screen which spread s the light striking it. Screen gain is less than 1 but audience viewing angles are increased. An adjustment that affects the display of an image. Such display settings include contrast, brightness, tint, blanking, size, offsets, a[...]

Appendix A: Glossary A-4 Christie DS+60/DW30/Matrix 3000 User ’s Manual 013-100149-02 Rev. 1 ( 01/07) A physical connection route for a source signal, described by a 2-digit number representing 1) its switcher/projector location and 2) its slot in the switcher/projector. Signal sent from a source device to the projector. A device, such as the Ser[...]

Appendix A: Glossary Christie DS+60/DW30/Matrix 3000 User’s Manual A-5 PAL (Phase Alternating Line) video is a 50 Hz standard with 768 x 576 resolution. It is found on some video tape and disk pl ay ers (used primarily in Europe, China and some South American and African countries). The smallest discernible element of data from a computer-generat[...]

Appendix A: Glossary A-6 Christie DS+60/DW30/Matrix 3000 User ’s Manual 013-100149-02 Rev. 1 ( 01/07) The output from certain video tape pla yers and video equipment. S-Video separates sync and luminance from color information, typically producin g a higher quality display than composite video. The horizontal or vertical frequency at wh ich image[...]

Appendix A: Glossary Christie DS+60/DW30/Matrix 3000 User’s Manual A-7 The frequency at which images are generated. Vertical frequencies vary amongst sources. Also called vertical scan rate. The difference between the center of the projected image and the center of the projector lens. For clarity, offset is often expressed as the maximum amount o[...]

[...]

Appendix B IR Remote Key Reference Christie DS+60/DW30/Matrix 3000 User’s Manual B-1 NOTE: The IR remote is a standard component provided with the pr ojector. Use the extension cable also provided to convert th e IR remote to a wired remote, if desired. Refer to Section 3 for a specific description of each key and how to use them correctly. Toggl[...]

[...]

Appendix C Serial Communication Cables Christie DS+60/DW30/Matrix 3000 User’s Manual C-1 A serial link of RS232 or RS422 enables ASCII communication with the pro jector so that it can be controlled remotely from a PC or other controller. Fr om a PC, connect a standard 9-wire RS232 serial cable to the RS232 IN port. Or, for long-distance (>100 [...]

[...]

Appendix D Throw Distance Christie DS+60/DW30/Matrix 3000 User’s Manual D-1 Calculating Throw Distance It is important throw distance be precisely calculated for your installation using the appropriate formula from the chart below. To calculate throw distance you must know the screen size and the lens type installed in the projector. In general, [...]

[...]

Appendix E System Integration Christie DS+60/DW30/Matrix 3000 User’s Manual E-1 The GPIO connector located on the input panel provides a flexible method of interfacing a wide range of external I/O devices to the projector. There ar e 7 GIO pins available on the 9pin D-Sub GPIO connector, which are configurable via RS232 commands. The other two pi[...]

Appendix E: System Integration E-2 Christie DS+60/DW30/Matrix 3000 User’s Manual Query Command (GIO?) Request the state and configuration of al l pins (GIO! “HHLLHLH” “OOIOOOI”) Repl y of pin state and confi guration (GIO? C2) Request configuration for pin #2 (GIO! C2 O) Reply with pin #2 configuration as output (GIO? 2) Request the state[...]

Appendix F Optional Input Modules Christie DS+60/DW30/Matrix 3000 User’s Manual F-1 There are many optional input modules and accessories currently available for this projector . Contact your dealer for a complete and up-to-date listing. NOTE: Always unpl ug the projector or swi tcher before i nstalling or removing any optional input module. The [...]

Appendix F: Optional Input Modules F-2 Christie DS+60/DW30/Matrix 3000 User’s Manual The RGB400 ALT Input Module m ay be installed in this projector, a Marquee Signal Switcher , or a Marquee Case/Power Supply . The module receives analog RGB input signals from computers or other RGB source devices. Video inputs are 75 Ω terminated. Video outputs[...]

Appendix F: Optional Input Modules Christie DS+60/DW30/Matrix 3000 User’s Manual F-3 This module can display digital video input signals co nforming to the DVI (Digital Visual Interface) single-channel standard. Features ◊ supports Digital Visual Interface (DVI) single-channel ◊ supports VESA ® Extended Display Identification Data (EDID ™ [...]

[...]

Appendix G 300W P-VIP ® Product Safety Data Sheet Christie DS+60/DW30/Matrix 3000 User’s Manual G-1[...]

Appendix G: 300W P-VIP Product Safety Data Sheets G-2 Christie DS+60/DW30/Matrix 3000 User’s Manual[...]

Appendix G: 300W P-VIP Product Safety Data Sheets Christie DS+60/DW30/Matrix 3000 User’s Manual G-3[...]

[...]

Index Christie DS+60/DW30/Matrix 3000 User’s Manual A Adjusting Input Levels, 3-29 Advanced Image Settings, Submenu, 3-31 Anamorphic, 3-22 Arrow Key, 3-9 Arrow Keys, 3-9 Auto Input Level, 3-28 Auto Key, 3-5 Auto Setup, 3-5, 3- 19 Automa tic Gain Contr ol (AGC ), 3-26 AutoSource Checkbo x, 3-19 B Bad Sync, 3- 67 Baud Rate, 2-18, 3-36 Blacklevels a[...]

Index Christie DS+60/DW30/Matrix 3000 User’s Manual Error Messages Bad Sync, 3- 67 H-Sync or V-Sy nc, 3-67 No Signal, 3-67 System Warnings/Error s, 3-67 Ethernet Communi cations, 2-16 Troubleshooting, 5- 3 Ethernet Networ k, 2-18 Ethernet Settings, 3-37 Exit Key, 3-9 F Film Mode T hreshold, 3-33 Frame Delay, 3-33 Frame Delay Monitor, 3-33 Frame L[...]

Index Christie DS+60/DW30/Matrix 3000 User’s Manual Replacement, 4-8 Lens Mount, 3-2 Level Value, 3-47 Locked Channel Ch eckbox, 3-19 Luma Delay, 3-28 M Menu Channel Edit, 3-18 Channel Setup, 3-16 Configurati on, 3-34 Image Setti ngs, 3-24 Lamp, 3-51 Main, 3-10 PIP and Switching , 3-48 Size and Position, 3-20 Status, 3-55 Menu Font Size, 3-35 Men[...]

Index Christie DS+60/DW30/Matrix 3000 User’s Manual Splash Screen Setup. See Menu:S plash Screen Setup Split Network, 3-36 Split Networks Options for Setu p, 2-19 S-Video Connection, 2- 14 Swap Main and PIP Image. See PIP Switcher, 3- 18 Sync Def. and types, 6 System Integration GPIO Connect or, 2-19 T Temperature, 2-5 Non-Operating, 6-5 Operatin[...]