TANDBERG MSE 8510 инструкция обслуживания

Codian MCU MSE 8510 Getting started[...]

Codian MCU MSE 8510 Getting started[...]

Copy right © Codian 2008. All rights reser ved. This Getting Star ted Guide ma y not be copied, photocopied, translated, r eproduc ed, or con verted into any electronic or machine-readable form in whole or in par t without prior wr itten appro v al of Codian Limited. Codian Limited reser ves the r ight to revise this documenta tion and to make cha[...]

T able of conten ts General inf ormation .......... .......... .......... ........... .......... .......... ............. .......... ........... .......... .. .... . 1 About the M SE 8510 Media 2 blade ........... ............ ............. .......... ............. ........... 1 Port and L ED location .............. ........... ............ .......[...]

General information 1 General informa tion About the MSE 8510 Media2 blade The MSE 8510 Media2 blade is a technologically adv anced media processor that fits into an MSE 8000 chassis. It can be used as a Multipoint Control Unit (MCU) combining continuous presence high defini tion video conferencing and the highest possible v oice quality . P ort an[...]

2 LED behavior T able 1 descr ibes the behavior of the LEDs . T able 1: Media2 blade LED behavior LED Co lor Indicates USB P or t Activity Green Reser ved for futur e expansion Admin P or t Activity Green Reser ved for future expansion Status Green The Media2 blade is opera ting nor mall y Alar m Red The Media2 b lade is booting or has dev eloped a[...]

Installing the Media2 blade 3 Installing the Media2 blade Step one: Install the Media2 blade into the MSE 8000 chassis 1 Remov e the blade or blanking blade from the slot into which you are going to install the Me dia2 blade: i Using a No .1 Phillips scre wdriver , loosen the scre ws in the retaining latches with an anti-cloc kwise quar ter tur n. [...]

4 iii Slide out the blade or bl anking bl ade. 2 Open both retaining la tches on the front of the Media2 b lade. When open, a retaining latch is at a 90 ° angle perpendicular to the front of the blade . 3 Slide the Media2 blade into the b lade slot (as sho w n in Figure 2) un til it stops. 4 Simultaneousl y close both retaining latches on the blad[...]

Installing the Media2 blade 5 Figur e 3: Closing the retaining latches on the front of a blade Step two: C onnec t to Ethernet Port A Connect an Ethernet cable from Ethernet P or t A to an Ether net switch (rather than a hub , to minimize interference from othe r devices on the netw ork). The Ether net por t is a 10/100/1000 Mbps auto-sensing conne[...]

6 Initial configur ation Step one: Configur e Ethernet Port A settings The default setting for the Media2 blade Ether net por ts is auto-sensing mode . If the switch por ts to which you con nect the Media2 blade ar e not also set to auto-sensing mode, then y ou need to configure the Medi a2 blade Ethernet por ts to use the same speed and duplex mod[...]

Configuring the Media2 blade 7 Co nfiguring the Media2 blade Step one: Log in to the Media2 blade All administration of the Medi a2 blad e is perfor med via the w eb interface. T o log in to the w eb interface of the Media2 b lade: 1 Log in to the Super visor’ s web interface . 2G o t o Hardware > Blades and clic k the IP address of the Media2[...]

8 T o configure the Media2 b lade to use a SIP registrar: 1 In the w eb interface , go to Settings > SIP . 2 Configure the settings y ou requir e , usin g the online help for fur ther assistance. 3C l i c k App ly c han ges . Step four: Add endpoints (optional) One wa y to add par t icipants to a confer ence that you cr eate is to hav e the Medi[...]

Using the Media2 blade 9 Using the Media2 blade Creating conferences T o crea te a conference: 1 In the w eb interface of the Media2 b lade, go to Conf er en ce s and click Ad d n ew confer ence . 2T y p e a Name for the conference, for example SalesMeeting . 3 T ype an optional numeric identifier , for example 123 . This will be the telephone numb[...]

10 Calling partic ipants in to a conferenc e T o call par ticipants in to a conference: 1 In the w eb interface of the Media2 blade, go to Con fe re nc es and click on the name of an activ e conference . 2O n t h e Pa r ti c ip an ts tab , click Add par ticipant to call out to an H.323 or SIP endpoint. 3I n t h e Address field: where there is no H.[...]

Using the Media2 blade 11 Streaming conferences Streaming is a wa y of viewing a conference in a standard w eb bro wser . The Media2 blade allo ws streaming of video and, if enabled for a confer ence , the streaming of data. Y ou can also conduct a text ‘chat’ and add notes and dra wings to the data stream. Y ou can configure tw o streaming opt[...]

12 Instruc ting confer ence par ticipants Y ou need to tell conference par ticipants ho w to join conferences . Y ou can also tell them ho w to use the Far-End Camera Contr o ls (FECC) to na vigate menus in the auto attendant and choose conference la youts. Ther e is a document: Getting Started: Accessing Conferences a vailable in the documenta tio[...]

Troubleshooting and tec hnical support information 13 T r oubleshooting and technical suppor t information Using the ev ent log to help solve a problem Unless you are ex periencing a prob lem, all e v ent logging sources should be set to the default, which is Errors, warnings and information . F or more infor mation about configur ing the ev ent lo[...]

61-0021-01[...]