Sony SLV-D910R инструкция обслуживания

AEP Model SL V -D910B/D910E/D910N/D950B/D950E UK Model SL V -D950GI E Model SL V -D910AZ Russian Model SL V -D910R SERVICE MANUAL DVD PLA YER/ VIDEO CASSETTE RECORDER SPECIFICA TIONS RMT -V503A/V503B TS-10 MECHANISM Refer to the SERVICE MANUAL of VHS MECHANI- CAL ADJUSTMENT MANUAL VII for MECHANICAL ADJUSTMENTS. (9-921-790-11) PA L System Laser Sem[...]

— 2 — LP: P AL 11.70 mm/s (recording/playback) NTSC 16.67 mm/s (playback only) SL V -D910B/D950B: SECAM 11.70 mm/s (recording/playback) MESECAM 11.70 mm/s (playback only) SL V -D910N/D910R: MESECAM 11.70 mm/s (recording/playback) EP: NTSC 11.12 mm/s (playback only) Maximum recording/playback time 10 hrs. in LP mode (with E300 tape) Rewind time [...]

— 3 — W ARNING!! WHEN SER VICING, DO NO T APPRO A CH THE LASER EXIT WITH THE EYE TOO CLOSEL Y . IN CASE IT IS NECESSAR Y T O CONFIRM LASER BEAM EMISSION, BE SURE T O OBSER VE FROM A DIST ANCE OF MORE THAN 25 cm FROM THE SURF ACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CAUTION Use of controls or adjustments or performance of procedur[...]

— 4 — TABLE OF CONTENTS Precautions 1 Safety Precautions ·································································· 5 2 Servicing Precautions ···························································· 7 3 ESD P[...]

— 5 — PRECAUTIONS 1 SAFETY PRECAUTIONS 1) Before returning an instrument to the customer , always make a safety check of the entire instrument, including, but not limited to, the following items: (1) Be sure that no built-in protecti ve de vices are defectiv e or have been defeated during servicing. (1)Protecti ve shields are provided to protec[...]

— 6 — 6) Product Safety Notice-Some electrical and mechanical parts ha ve special safety-related characteristics which are often not e vident from visual inspection, nor can the protection they gi ve necessarily be obtained by replacing them with components rated for higher v oltage, wattage, etc. P arts that have special safety characteristics[...]

— 7 — 2 SERVICING PRECAUTIONS CA UTION: Before servicing units co vered by this service manual and its supplements, read and follo w the Safety Precautions section of this manual. Note: If unforseen circumstances create conflict between the follo wing servicing precautions and any of the safety precautions, al ways follow the safety precautions[...]

— 8 — 3 ESD PRECAUTIONS Electrostatically Sensitive Devices (ESD) Some semiconductor (solid state) de vices can be damaged easily by static electricity . Such components commonly are called Electrostatically Sensiti ve De vices (ESD). Examples of typical ESD devices are integrated circuits and some field-ef fect transistors and semiconductor ch[...]

— 9 — 4 HANDLING THE OPTICAL PICK-UP The laser diode in the optical pick up may suffer electrostatic breakdo wn because of potential static electricity from clothing and your body . The follo wing method is recommended. (1) Place a conductiv e sheet on the work bench (The black sheet used for wrapping repair parts.) (2) Place the set on the con[...]

— 10 — 5 PICK-UP DISASSEMBL Y AND REASSEMBL Y 5-1 Disassembly 1) Remov e the power cord. 2) Disassemble the Deck-Assy . 3) Make solder land 2 points short on Pick-up. (See Fig. 4) 4) Disassembly the Pick-up. 5-2 Assembl y 1) Replace the Pick-up. 2) Remov e the soldering 2 points on Pick-up. 3) Reassemble the Deck-Assy . Note: If the assembly an[...]

1-1 8 Unpacking Getting Started Step 1 : Unpacking Check that you have receiv ed the following items with the DVD-VCR: •R em ote commander • PERITEL cable •R 6 ( s i z e AA) batteries • Audio cord (pinpl ug ×2 y pinplug ×2) •A erial cable • V ideo cord (pinpl ug ×1 y pinplug ×1) Check your model nam e The instructi ons in this manua[...]

1-2 12 Connecting the DVD-VCR Additional connect ion To a satellite or digital tuner wi th Line Throu gh Using the Line T hrough func tion, you can watch programmes from a satellite or digital tuner connec ted to this D VD-VCR on the TV e ven when the DVD-VCR is turned off. Wh en you turn on the satellite or digit al tuner, t his D VD-VCR automatic[...]

1-3 16 Setting the clock S tep 6 : Se tting the clock Yo u m u st set the time and date on the DVD- VCR to use the timer features properly. The Auto Clock Set function work s only if a station in you r area is broa dcasting a time signal. Before y ou start… •T u r n on th e DVD-VCR and your TV . •T o control the DVD-VCR, set T V / D VD·VIDEO[...]

1-4 20 Presetting channels If the picture is no t clear If the picture is not clear, you may use the Manual Fine Tuning (REGL.FIN) function. After ste p 7, press V/v to select “REGL.FIN”. Press B/b to get a clear picture. Then press ENTER. Tips •T o s e t t h e pr ogramme po sition for th e decoder, see “Set ting the C anal Plus de coder”[...]

1-5 24 Presetting channels Note •B e sure to sel ect the p rogramme position you want to disable correctly. If you di sable a programme po sition by mistake, you need to reset that channel manuall y . 3 Pre ss V/v to select “Installation Ma nuelle”, th en press ENTER. 4 Pre ss V/v to s elect the row w hich y ou wan t to disable. To d i splay [...]

1-6 28 Setting the Canal Plus decoder Setting Canal Plus channels To w a t c h or record Can al Plus prog rammes, set your DVD-VCR to receiv e the chan nels using the on -screen displa y. In order to set the channels correctly , be sure to follow all of the steps below . Before y ou start… •T u r n on th e DVD-VCR and your TV . •T o control t[...]

1-7 32 Playing discs Additional tasks * If you pause the DVD play er for more than 5 minut es, the D VD player will au tomatically stop. To Resume playbac k for the current disc (Resume Play) The D VD player remembe rs the point where you stop ped the disc ev en if the DVD player ent ers standby m ode by pre ssing ?/1 . Tip •T o begin pl ayback f[...]

1-8 36 Gui de to the on-screen display To playback fr om the desired title/trac k counter position Tip •Y ou can change the co unter position inform ation (playing ti me or remaining time) usi ng B/b (DVD and CD only). DVD CD Notes •T h e d i spla y may not chan ge as oper ated depend ing on the disc. •T he display window continue indic ating[...]

1-9 40 Recording TV programmes Record ing TV prog rammes Before y ou start... •T u r n on th e DVD-VCR and your TV . •S witch the input se lector on your TV so th at the signal from the playe r appears on the TV screen. •S e t T V / DVD· VIDEO to D VD·VIDEO , then press SELECT VIDEO to control the VCR (page 9). •T o record from a decoder [...]

1-10 44 Recording TV programmes using the ShowView ® s ystem (SL V -D950B only) Recor ding TV pr ogrammes using the Show View ® system (SL V -D950B only) The ShowV iew system is the feature that simplifies prog ramming the VCR to make timer recordings. Just enter the ShowV iew nu mber listed in the TV programme guid e. The date, tim es, and progr[...]

1-11 48 Recording TV programmes using the timer Record ing TV programmes u sing the timer Yo u can preset up to six programmes at a time. Before y ou start… •C he ck that the D VD-VCR clock is set to the correct time. •T u r n on th e DVD-VCR and your TV . •S witch the input se lector on your TV so th at the signal from the playe r appears [...]

1-12 52 Recording TV programmes using DIAL TIMER (SL V -D950B only) Recor ding TV pr ogrammes using DIAL TIMER (SL V -D950B only) The Di al Timer function allows you to make timer recordings o f programmes without tu rning on yo ur TV . Set the recordin g timer to r ecord up to six programm es that will be broadcas t within a month using DIAL TIMER[...]

1-13 56 Checking/changing/cancelling timer settings Checking/changin g/canc elling ti mer settings Before y ou start… •C he ck that the D VD-VCR clock is set to the correct time. •T u r n on th e DVD-VCR and your TV . •S witch the input se lector on your TV so th at the signal from the playe r appears on the TV screen. •S e t T V / D VD·[...]

1-14 60 A/V Receiver hookup B Use this hookup if y our A/V receiver has a Dolby Digital, MPEG audio or DTS ∗ de co der, a digi tal in put jack a nd 6 spe akers This connection will allow you to use t he Dolby Digital, MPEG audio or DTS d ecoder function of your A V amplifier (receiver). Y ou are not able to enjoy the surround so und effects of th[...]

1-15 64 A udio Setup •A ud io DRC (Dynamic Range Control) M akes the sound clear when t he volume is turned down when playing a DVD that co nf orms to “ Audio DRC”. Thi s affects the output from the following jacks: – OUT AUDIO L/R jacks –D IGIT AL AUDIO OUT (OPTICAL or COAXIAL) jack only when “Dolby Digital” is set to “D-PCM ”. T[...]

1-16 68 Setting the display or sound track language Setting the displ ay or sound trac k lang uage You can set vario us languag es for the disc’ s me nu, sound tra ck or subti tle. 1 Pre ss SET UP when the DVD player is in stop mode , then pres s V/v to select (D VD) and pr es s ENTER . 2 Pre ss V/v to select “Régl age de la langue”, th en p[...]

1-17 72 Par ental Control (limiting pla yback by children) To change the passw ord To turn off the Parent al Control function Set “Utiliser le Cod e” to “Non” in step 3 on page 71. To p l a y a disc for whic h Parental Contr ol is set If you f orget your pas sword Notes •W h e n you play DVDs which do not have the Paren tal Control functi[...]

1-18 76 Changing the angles Changing the a ngles Note •D e p ending on the DVD , you may not be able to change th e angles eve n if multi-angles are recorded on the DVD. If various angles (multi-angles) for a scene are recorded on the DVD, “ ” appears in the display wh en you press ANGLE during pl ayb ack. This means that you can change the v[...]

1-19 80 Va ri ou s pla y m ode functions (Programme play , Shuffle play , Repeat play) Playing in random or der (Shuffle play) To return to normal play Press CLEAR during shuffle play . Yo u c a n shuffle the pla yback order of tracks. Subs equent “shuffling” may pro duce a dif ferent playing order . 1 Pre ss PROGRAM when the DVD player is in s[...]

1-20 84 Virtual surround setting Notes •S ur round effects cannot be obta ined for DTS or linea r PCM. •W he n the playing sign al does not contain a sig nal for the rear speakers, the surround effects will be diff icult to hear . •W he n you activate the surround effect , turn off the surround settin g of the conne cted TV or amplif ier (rec[...]

1-21 88 Playing an MP3 audio track Tips • If you add num bers (01, 02, 03, etc. ) to the front of th e track file names, the tra cks will be played i n that order. •A disc with many trees takes longer to start playback . Some discs with many trees cannot be played b ack. Notes •D e p e nding on the software yo u use to create the DA TA CD, th[...]

1-22 92 Playing JPEG image files Tip • If you add num bers (01, 02, 03, etc. ) to the front of th e file names, the files will be playe d in th at order. Notes •T h e s y s t e m can play the e xtension “ .JPG” or “.JPE G”. •S ome CD-Rs or CD-RWs cannot be played on this syst em dependi ng on file format. • If you add the extensio n[...]

1-23 96 Qu ic k Ti mer Recording Quic k Timer Recordi ng After you have sta rted recor ding, you can ha ve the VCR stop recording au tomatica lly after a specified duration. 1 While re cording, press z REC. 2 Pre ss z REC repeatedly to set the duration time. In SP mode Ea ch press advances the time in increments of 30 minut es. In LP mode Ea ch pre[...]

1-24 100 Recording stereo and bilingual programmes How sound is recorded on a video tap e The VCR re cords s o und on to two separate track s. Hi-fi audio is reco rded onto the main trac k along with the pi cture. Monau ral sound is re corded onto th e normal aud io tr ack along the edge o f the tape. Notes •T o li sten to play back sounds in ste[...]

1-25 104 Adjusting the picture (tracking) 2 Pre ss V/v to select “Réglages Utilisateur”, th en press ENTER. 3 Pre ss V/v to select “Smart Trilogic”, the n press b . 4 Pre ss V/v to set “SMAR T TRILOGIC” to “OUI” or “NON”. • OUI: Picture sharpness is automatically adjusted. • NON: Adjust the picture sharpness manua lly . To [...]

1-26 108 Edit ing E xample C How to connect to a stereo system Connect the LINE-2 IN t / o L/R jacks on this D VD-VCR to the audio o utput jacks on the stereo system, us ing an audio cabl e (not supplied ). Notes •M ak e sure you conn ect the plugs to jack s of the same colour. • If the other VCR is a monaural t ype, leave the red plugs un conn[...]

1-27 112 Tr oubleshooting Tr o u b l eshooting If yo u have any questions or pro blems not covered below, please consult your n earest Sony service facility . Ge neral T rouble shooting DV D Tr oubleshooting Symptom Remedy Powe r The ?/1 (on/standby) switch does not function. •C o n ne ct the mains lead to the mains securely . The power is turned[...]

1-28 116 Tr oubleshooting Timer recording The timer do es not operate. • Check that th e clock is set. •M ake sure a tape has been inserted. •C h e c k t h at the safety tab has not been remov ed. •M ake sure the tape is not at its end. •M ak e sure a programme has been se t for timer record ing. •M a k e sure your timer settings are pa[...]

1-29 122 I ndex to parts and controls Display windo w A DV D i n dicator ( 32) B Disc i ndicator (32) C M ONTH indicator ∗ (52) D DAY i n dicator ∗ (5 2) E YEAR indicator ∗ (52) F DA TE ind icator ∗ (52) G Ta p e indicato r (37) H VCR in dicator (37) I Ti me r in dica tor (4 6) J Re cor ding indi cator (41) K STEREO indicator (98) L Pl ayin[...]

1-30E 126 DV D Audio/Subtitle Language DV D A u dio/Subti tle Language Abbre v iation Language ARA A ra bic CHI Chine se CRO Croatian CZK Czech DAN D an is h DEU Germa n ENG E nglish ESP Spa nish FIN Fi nish FRA French GRE G reek HUN Hun garian ID NI n donesian IND Hi ndi ISL Ice la ndic IT A Ita li an IWR Hebrew JPN Jap anese KOR K orean MAL M ala[...]

2-1 2-1-2 Bottom Cover Removal Œ RELEASE 12 HOOKS <SLV-D910> Œ RELEASE 12 HOOKS <SLV-D950> 2. DISASSEMBL Y AND REASSEMBL Y 2-1 CABINET AND PCB Fig. 2-1 Cabinet T op Removal Fig. 2-2 Bottom Cover Removal 2-1-1 Cabinet T op Removal 2-1-3 Ass’y Front Panel Removal Fig. 2-3 Ass’y Front Panel Removal 2-1-4 Function PCB Removal Fig. 2-4[...]

2-2 Fig. 2-5 Chassis Removal 2-1-5 Chassis Removal 2-1-6 VCR Main PCB Removal Fig. 2-6 VCR Main PCB Removal Œ REMOVE 2 SCREWS ˇ REMOVE 3 SCREWS ˆ REMOVE 4 SCREWS Ø REMOVE 3 SCREWS ¨ REMOVE 2 SCREWS ´ REMOVE 4 SCREWS VCR MAIN PCB DVD MAIN PCB S.M.P .S. PCB DVD DECK VCR DECK Œ REMOVE 3 SCREWS MODE SWITCH When installing the ass'y full dec[...]

2-3 Fig. 2-7 Circuit Board Locations 2-2 CIRCUIT BOARD LOCA TIONS S.M.P.S. PCB FUNCTION PCB VCR MAIN PCB DVD MAIN PCB[...]

2-4 2-3 VCR DECK P ARTS LOCA TIONS 2-3-1 T op View 1 2 3 4 5 6 1 GEAR FL CAM 2 MOTOR LOADING ASS’Y 3 LEVER FL ARM ASS’Y 4 HOLDER FL CASSETTE ASS’Y 5 LEVER FL DOOR 6 SLIDER DRIVE Fig. 2-8 T op parts Location-1[...]

2-5 1 2 6 78 9 q a q ; q s qd q; 34 5 1 FE HEAD 2 CYLINDER ASS’Y 3 ACE HEAD ASS’Y 4 LEVER UNIT PINCH ASS’Y 5 LEVER #9 GUIDE ASS’Y 6 LEVER TENSION ASS’Y 7 BAND BRAKE ASS’Y 8 DISK S REEL 9 LEVER S BRAKE ASS’Y q; GEAR IDLE qa LEVER IDLE qs LEVER T BRAKE ASS’Y qd DISK T REEL Fig. 2-9 T op Parts Location-2[...]

2-6 2-3-2 Bottom View 1 23 4 5 6 7 8 9 q; 1 GEAR JOINT 1 2 GEAR JOINT 2 3 BRAKET GEAR 4 MOTOR CAPST AN ASS’Y 5 LEVER T LOAD ASS’Y 6 GEAR LOADING DRIVE 7 LEVER S LOAD ASS’Y 8 HOLDER CLUTCH ASS’Y 9 BEL T PULLEY q; SLIDER CAM Fig. 2-10 Bottom Parts Location[...]

2-7 "B" "A" 1 LEVER FL DOOR 2 HOOK 2-4 VCR DECK 2-4-1 Holder FL Cassette Ass’y Removal 1) Pull the Holder FL Cassette Ass’y 1 to the eject position. 2) Pull the Holder FL Cassette Ass’y 1 as grasping the Holder FL Cassette Ass’y 1 and Lever FL Cassette-R 2 in the same time to release hooking from Main Base until the Boss[...]

2-8 1 SLIDER FL DRIVE 2 GEAR FL CAM 2-4-3 Slider FL Drive, Gear FL Cam Removal 1) Pull the Slider FL Drive 1 to the front direction. 2) Remove the Slider FL Dri ve 1 in the direction of arrow . (Refer to Fig. 2-13) 3) Remove the Gear FL cam 2 . Note: When reinstalling be sure to reassemble Slider FL driv e 1 after you insert the Boss of Le ver FL A[...]

2-9 3 CONNECTOR WAFER 2 CONNECTOR WAFER 1 CABLE FLA T 1 GEAR WORM WHEEL 2-4-5 Gear Worm Wheel Removal 1) Remove the Gear W orm wheel 1 . Fig. 2-16 Gear Worm Wheel Removal 2-4-6 Cable Flat Removal 1) Remove the Drum connecting part of Cable Flat 1 from Connector Wa f f er 2 . 2) Remove the Loading Motor connecting part of Cable Flat 1 from Connector[...]

2-10 1 GEAR JOINT1 2 GEAR JOINT2 3 SLIDER CAM TIMING POINT 1 TIMING POINT 2 2 MOTOR LOADING ASS`Y 1 SCREW 1 SCREW 2 BRAKET GEAR 4 GEAR JOINT 1 3 GEAR JOINT 2 2-4-7 Motor Loading Ass’y Removal 1) Remove the scre w 1 . 2) Remove the Motor Loading Ass’y 2 . Fig.2-18 Motor Loading Ass’y Removal 2-4-8 Bracket Gear , Gear Joint 2, 1 Removal 1) Remo[...]

2-11 2-4-9 Gear Loading Drive, Slider Cam, Lever Load S, T Ass’y Removal 1) Remove the Belt Pulley . (Refer to Fig. 2-38) 2) Remove the Gear Loading Dri ve 1 after releasing Hook [A] in the direction arrow as sho wn in detail drawing. 3) Remove the Slider Cam 2 . 4) Remove the Le ver Load 3 , Link Load 5 & Lev er Load 4 , Link Load 6 . Fig. 2[...]

2-12 1 SPRING TENTION LEVER STOPPER MARK[B] "A" 2 LEVER TENTION ASS`Y 3 BAND BRAKE ASS`Y 2-4-11 Lever Pinch Drive, Lever T ension Drive Removal 1) Remove the Le ver Pinch Dri ve 1 , Lev er T ension Driv e 2 . Fig. 2-23 Lever Pinch Drive, Lever T ension Drive Removal 2-4-12 Lever T ension Ass’y , Band Brake Ass’y Removal 1) Remove the [...]

2-13 2-4-13 Lever Brake S, T Ass’y Removal 1) Release the Hook [A] and the Hook [B], [C] in the direction of arrow as sho wn in Fig 2-25. 2) Lift the Lever S, T Brake Ass’y 1 , 2 with spring brake 3 . Assembly: 1) Assembly the Lever S Brak e Ass’y 1 on the Main Base. 2) Assembly the Lever T Brake Ass’y 2 with spring brake 3 . Note: Ta ke ex[...]

2-14 2-4-15 Disk S, T Reel Removal 1) Lift the Disk S, T Reel 1 , 2 . Fig. 2-27 Disk S, T Reel Removal 2-4-16 Holder Clutch Ass’y Removal 1) Remove the W asher Slit 1 . 2) Lift the Holder Clutch Ass’y 2 . Note: When you reinstall Holder Clutch Ass’y 1) Check the condition of spring as shown in detail A. 2) Don't push Holder Clutch Ass’[...]

2-15 2-4-17 Lever Up Down Ass’y , Gear Center Ass’y Removal 1) Remove the 2 hooks in the direction of arro w as shown Fig. 2-29 and lift the Le ver Up Down Ass’y 1 . 2) Lift the Gear Center Ass’y 2 . Assembly: 1) Insert the Lever Up Do wn Ass’y 1 in the rectangular holes on Main Base as shown in Fig 2-30. 2) Lift the Lever Up Do wn Ass’[...]

2-16 2-4-19 Lever Unit Pinch Ass’y , Plate Joint, Spring Pinch Drive Removal 1) Lift the Unit Pinch Ass’y 1 . 2) Remove the Plate Joint 2 from Le ver Pinch Driv e. 3) Remove the Spring Pinch Dri ve 3 . Note: 1) T ake extreme care not to touch the grease on the Roller Pinch. 2) When reinstalling, be sure to apply grease on the post pinch roller [...]

2-17 2-4-21 FE Head Removal 1) Remove the scre w 1 . 2) Lift the FE Head 2 . Fig. 2-34 FE Head Removal 2-4-22 ACE Head Removal 1) Pull out the FPC from connector of ACE Head Ass’y 2 . 2) Remove the scre w 1 . 3) Lift the ACE Head Ass’y 2 . Fig. 2-35 ACE Head Removal 1 FE HEAD 1 SCREW 2 HEAD ACE ASS`Y[...]

2-18 2-4-23 Slider S, T Ass’y Removal 1) Move the Slider S, T Ass’y 1 , 2 to slot, and then lift it to remov e. (Refer to arrow) Fig. 2-36 Slider S, T Ass’y Removal 2-4-24 Plate Ground Deck, Cylinder Ass’y Removal 1) Remove the 3 Screws 1 . 2) Lift the Plate Ground Deck 2 . 3) Lift the Cylinder Ass’y 3 . Assembly: 1) Match the 3 holes in [...]

2-19 2-4-25 Belt Pulley Removal 1) Remove the Belt Pulley 1 . Note: Ta ke e xtreme care not to get grease on Belt Pulley 1 at assembling or reassembling. Fig. 2-38 Belt Pulley Removal 2-4-26 Motor Capstan Ass’y Removal 1) Remove the Damper Capstan 1 in the direction of arro w . 2) Remove the 3 Scre ws 2 . 3) Remove the Motor Capstan Ass’y 3 . A[...]

2-20 2-4-27 Post #8 Guide Ass’y Removal 1) Rotate the Post #8 Guide Ass’y 1 in the direction of arro w to lift up. Fig. 2-40 Post #8 Guide Ass’y Removal 2-4-28 Level Head Cleaner Ass’y Removal (Optional) 1) Release the Hook 1 . 2) Lift the Lever Head Cleaner Ass’y 2 . Fig. 2-41 Lever Head Cleaner Ass’y Removal 2-4-29 How to Eject the Ca[...]

2-21 1) The replacement time of parts is not life of parts. 2) The table 2-1 is that the VCR Set is in normal condition (normal temperature, normal humidity). The checking period may be changed owing to the condition of use, runtime and en vironmental conditions. 3) Life of the Cylinder Ass’y is depend on the condition of use. 4) See exploded vie[...]

2-23 2-6-2 Ass’y P/U Deck Removal 1) Disconnect DCN2 1 , DCN3 2 . 2) Lift down the Assy P/U Deck 3 while simultaneously pushing 2 Hooks 4 , 5 in the direction of arrow “ A”, “B”. Fig. 2-45 Assy P/U Deck Removal 1 DCN2 2 DCN3 3 ASSY- P/U DECK <Assembly Point> SLIDER HOUSING "B" "A" 5 HOOK 4 HOOK[...]

2-23 2-6-2 Assy P/U Deck Removal 1) Disconnect DCN2 1 , DCN3 2 . 2) Lift down the Assy P/U Deck 3 while simultaneously pushing 2 Hooks 4 , 5 in the direction of arrow “ A”, “B”. Fig. 2-45 Assy P/U Deck Removal 1 DCN2 2 DCN3 3 ASSY- P/U DECK <Assembly Point> SLIDER HOUSING "B" "A" 5 HOOK 4 HOOK[...]

2-24 2-6-3 Housing Ass’y Removal 1) Remove Belt 1 . 2) Push the Hook 2 in the direction arrow “ A” and lift up Pulley Gear 3 . 3) Push the Slider Housing 5 in the direction arrow “B” and lift up the Gear T ray 4 . 4) Lift up the Slider Housing 5 . 5) Remove 2 Screws 6 and lift down the Motor Load Assy 7 . 6) Remove Clamper Ass’y 8 . Fig[...]

2-25 2-6-4 Sub Chassis Removal 1) Remove the Soldering of Motor Feed (+, - wire) 1 . 2) Remove the 4 Scre ws 2 . 3) Lift up the Ass’y Brkt Deck 3 . Fig. 2-47 Sub Chassis Removal 2 4 SCREWS 3 ASSY-BRAK DECK 1 SOLDERING OF MOTOR FEED (+, - WIRE)[...]

2-26E 2-6-5 Ass’y Brkt Deck Removal 1) Push the Hook 1 in the direction arrow “ A” and lift up Gear Feed B 2 . 2) Remove 3 Scre ws 3 and 3 Holder Cam Skew 4 . 3) Remove Shaft Pick-Up 5 and Pick-Up Assy 6 . 4) Remove Gear Feed A 7 . 5) Remove 2 Scre ws 8 . 6) Remove Motor Feed Ass’y 9 . 7) Remove 3 Scre ws q; . 8) Remove Motor Spindle qa . F[...]

3. BLOCK DIAGRAM 3-2 3-1 DECK ASS'Y (DP-9) SIC3 (FAN8728) Motor Driver Disk Motor Pick-up & I/V Amp Feed Motor SIC2 4M EDO RAM ZIC7 (24C02) EPROM Coaxial Super RIC1 (S5L1463) RF Amp & DPD ZIC1 (VADDIS5E) A/V Decoder AIC2 (PCM1742KE) 2CH Audio DAC IC701 (PT6961) LED Drive (DT701) VIC1 (LA73054) Video Amp 6CH S/W AUDIO L/R AUDIO L/R ZIC3[...]

3-4E MEMO[...]

4. PCB DIAGRAMS 4-1 VCR Main - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3 4-2 DVD Main - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-7 4-3 S.M.P .S. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-11 4-4 Funct[...]

4-3 4-4 4-1 VCR MAIN COMPONENT SIDE[...]

4-6 4-5 CONDUCTOR SIDE[...]

4-7 4-8 4-2 DVD MAIN COMPONENT SIDE[...]

CONDUCTOR SIDE 4-9 4-10[...]

4-12 4-11 4-3 S.M.P .S. COMPONENT SIDE CONDUCTOR SIDE[...]

4-14 4-13 4-4 FUNCTION COMPONENT SIDE CONDUCTOR SIDE 4-5 DIAL-TIMER (SL V -D950B/D950E/D950GI/D910AZ Only) COMPONENT SIDE CONDUCTOR SIDE[...]

4-16E MEMO[...]

5. SCHEMA TIC DIAGRAMS 5-2 5-1 ◆ Block Identification of Main PCB - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-3 VCR Main PCB 5-1 S.M.P .S. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-5 5-2 Power Drive - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -[...]

◆ BLOCK IDENTIFICA TION OF MAIN PCB 5-3 5-4 <Component Side> <Conductor Side> VCR MAIN PCB <Component Side> DVD MAIN PCB[...]

5-1 S.M.P .S. 5-6 5-5[...]

5-2 POWER DRIVE 5-7 5-8[...]

5-3 OSD/VPS/PDS 5-10 5-9[...]

5-4 A2/NICAM 5-11 5-12[...]

5-5 AUDIO/VIDEO 5-14 5-13[...]

5-6 Hi-Fi 5-15 5-16[...]

5-7 INPUT -OUTPUT 5-18 5-17[...]

5-8 TM 5-19 5-20[...]

5-9 SYSCON 5-21 5-22[...]

5-10 LOGIC/FUNCTION 5-23 5-24[...]

5-11 SECAM (SL V -D950B/D910B/D910R Only) 5-25 5-26[...]

5-12 DVD MAIN-MICOM/A V DECODER 5-27 5-28[...]

5-13 DVD SERVO 5-29 5-30[...]

5-32E 5-31 5-14 DVD AUDIO/VIDEO[...]

6-1 6. ALIGNMENT AND ADJUSTMENTS 6-1 VCR ADJUSTMENT 6-1-1 Reference 1) X-Point (T racking center) adjustment, “Head switching adjustment” and “NVRAM option setting” can be adjusted with remote cont rol. 2) When replacing the Main PCB Micom (IC601) and NVRAM (IC605; EEPROM) be sure to adjust the “Head switching adjustment” and “NVRAM o[...]

6-2 6-1-1(b) TEST location for adjustment mode setting Fig. 6-2 VCR Main PCB (T op View) Short-Circuit for few seconds and release. (Just one time)[...]

6-3 6-1-2 Head Switching Point Adjustment 1) Playback the alignment tape. 2) Intermittently short-circuit the two T est Points on VCR Main PCB while setting the adjustment mode. (See Fig. 6-2) 3) Press the “1, 0” buttons ; remote control adjustment operates automatically . (See Fig. 6-1) 6-1-3 NVRAM Option Setting 1) NVRAM Option is adjusted in[...]

6-4 6-2 DVD ADJUSTMENT 6-2-1 Location of T est Point Fig. 6-5 Location of test Point (DVD Main PCB - Bottom Side)[...]

6-5 6-2-2 Skew Adjustment 6-2-2(a) Adjustment Spec. and T est P oint < T able 6-2 > T est Disc Adjustment Spec. T est Point Adjustment Location TD V -533 “SKEW” Ass’y Deck - T op Side Chapter 14 Flat W avef orm (D VD Main PCB - Bottom Side) (See Fig. 6-6) (P/N: J-6090-135-A) (See Fig. 6-5) Fig. 6-6 Ass’y Deck (T op Side)[...]

6-6 6-2-2(b) SKEW Adjustment Method Needed to minimize the v ariations in Skew of the Pickup unit and to pro vide optimum match with the recorded signal on the Disc. 1) Connect an Oscilloscope to the “SKEW” T est Point (See Fig. 6-5). 2) Connect Power , Open the T ray and Play the TD V -533 Disc, Chapter 14. ◆ Set the Oscilloscope Range as fo[...]

6-7 6-3 VCR MECHANICAL ADJUSTMENT 6-3-1 T ape T ransport System and Adjustment Locations The tape transport system has been adjusted precisely in the factory . Alignment is not necessary except for the follo wing : 1) Noise observed on the screen. 2) T ape damage. 3) Parts replacement in the tape transport system. Lower flange height of tape guide [...]

6-8 6-3-2 T ape T ransport System Adjustment When parts are replaced, perform the required adjustments by referring to procedures for the tape transport system. If there are any changes to the tape path, f irst run a T -120 tape and make sure excessi ve tape wrinkle does not occur a t the tape guides. ◆ If tape wrinkle is observed at the guide ro[...]

6-9 b. ACE HEAD TIL T ADJUSTMENT 1) Playback a blank tape and observe the position of the tape at the lo wer flange of tape guide. 2) Confirm that there is no curl or wrinkle at the lo wer flange of tape guide as sho wn in Fig. 6-12 (B). 3) If a curl or wrinkle of the tape occurs, slightly turn the screw (A) tilt adjust on the A CE head ass’y . 4[...]

6-10 d. ACE HEAD POSITION (X-POINT) ADJUSTMENT 1) Playback the alignment tape (Color bar) 2) Inter mittently short-circuit the two T est Points on VCR Main PCB . (See Fig. 6-2) 3) Press the “0, 5” remote control buttons, then adjustment is operates automatically . (See Fig. 6-1) 4) Connect the CH-1 pr obe to “En velope” the CH-2 probe to ?[...]

6-11 (2) Linearity adjustment (Guide r oller S, T adjustment) 1) Playback the Mono Scope alignment tape (SP mode). 2) Observe the video en velope signal on an oscilloscope (triggered by the video switching pulse). 3) Make sure the video en velope wav eform (at its minimum) meets the specification sho wn in Fig. 6-14. If it does not, adjust as follo[...]

6-12 6) Play back the Mono Scope alignment tape (SP mode). 7) Connect an oscilloscope CH-1 to the “Env elope” and CH-2 to the “H’D SW Pulse” for triggering. 8) Turn the guide roller heads with a flat head ( ) dri ver to obtain a flat video RF en velope as sho wn in Fig. 6-16. Fig. 6-16 Guide Roller S, T Height Adjustment IDEAL ENVELOPE S [...]

6-13 (4) En velope Check 1) Make recordings on T -120 (E-120) and T -160 (E-180) tape. Make sure the playback output en velope meets the specif ication as shown in Fig. 6-18. 2) Play back a self recorded tape (recording made on the unit using with T -120 (E-120). The video en velope should meet the specification as sho wn in Fig. 6-18. In SP mode, [...]

6-14E MEMO[...]

7-1 7. TROUBLESHOOTING SL V -D910AZ/D910B/D910E/D910N/D910R/ D950B/D950E/D950GI No Power (Standby LED OFF) Fuse F1SD01 is OK? AL5.8V D1SS13. Check IC701, DT701. Change Fuse F1SD01. Check Trans PT1SD1. Yes Yes No AL5V IC601-14, 92, 69, 70, 41. Check D620, D692, L605. No AL5.8V L702. Check D601C. Yes No Yes Check D601C. AL5V IC701-9. 25 No Data IN, O[...]

7-2 LOAD A TAPE AND PRESS PLAY BUTTON TURN VCR POWER ON MECHANISM DOESN'T OPERATE IN PLAY MODE TAPE LOADING OPERATION (LOAD) IC601-74:HIGH IC601-75:LOW (END SENSOR) IC601-74 CYLINDER ROTATION SW 25Hz IC601-24 CYL FG.PG IC601-97 SEE IC601-9, (CYLINDER DOES NOT ROTATE) CHECK START/END SENSOR (S601/S602) IC601 NO NO NO NO LOW YES YES HIGH YES YES[...]

7-3 RECORD MODE DOESN'T OPERATE PLAY OPERATION LOAD VCR WITH A BLANK TAPE AND PRESS RECORD BUTTON REC MODE SAFETY TAB SEE (AUDIO MISSING IN RECORD MODE) CHANGE SW602 (REC SW) CHANGE TAPE SEE (PLAY MODE DOESN'T OPERATE) EJECT NO NO YES REC-VIDEO SEE (VIDEO MISSING IN RECORD MODE) NO YES YES YES (VCR Section) LOAD TAPE AND PRESS F.FWD BUTTO[...]

7-4 LOAD A TAPE REWIND DOESN'T OPERATE F.FWD OPERATION PRESS REWIND BUTTON REW INDICATOR IN THE DISPLAY PRESS REW KEY IN REMOTE CONTROL MECHANISM STATE IC601-76, 77, 78 CHECK MECHANISM CHECK TIMER CHECK IC601-58 SEE (FAST FORWARD DOESN'T WORK) NO NO NO YES STOP DOES CAPSTAN MOTOR ROTATE? CHECK IC601-25 (CM F/R) SEE (MECHANISM DOES NOT OPE[...]

7-5 REV. SEARCH DOESN'T OPERATE PLAY OPERATION PRESS REWIND BUTTON FOR REV. SEARCH CHECK CAP F/R LINE IS CAPSTAN SPEED CHANGED? SEARCH OPERATION FWD SEARCH END CHECK IC601 CHANGE DECK CHANGE IC601 SEE (PLAY DOESN'T OPERATE) NO (PLAY MODE) NO YES CAP F/R IC601-25 HIGH (SEARCH MODE) YES NO LOW CHECK IC601 H'D AMP/ENV COMP. CHECK CAPSTA[...]

7-6 PLACE VCR IN STOP MODE VIDEO MISSING IN EE MODE TUNER MODE OPERATION NO NO NO VIDEO SIGNAL IC301-48 APPLY VIDEO SIGNAL TO FRONT VIDEO INPUT JACK AND SET TO LINE MODE BY INPUT SEL BUTTON. CHECK JC801 VIDEO SIGNAL CHECK IC301-61 TO JC801-19 LINE CHECK TO TV CONNECTION. NO YES YES YES YES YES YES NO VIDEO SIGNAL JC801 YES VIDEO SIGNAL IC301-61 VID[...]

7-7 VIDEO MISSING IN PLAY MODE VIDEO EE MODE OPERATION PLACE THE VCR PLAY MODE CHANGE IC301 CHECK IC6P01, Q6P01, R6P10 CHECK CN301 CONNECTION CHECK Q3Q1, C395 CHECK IC601-24 CHECK VIDEO OUT LINE SEE PAGE 7-6 (VIDEO MISSING IN EE MODE) NO YES YES NO YES YES YES VIDEO FM IC301-21 VIDEO SIGNAL IC301-78 VIDEO SIGNAL IC301-65 VIDEO SIGNAL IC6P01-19 VIDE[...]

7-8 COLOR MISSING IN PLAY MODE FM-ENV IC301-25 COLOR SIGNAL IC301-58 COLOR-KILLER IC301-33(2V) COLOR-ROTARY IC301-70 CHANGE IC301 CHECK IC301-27, 34 XT301 CHECK IC601-29 SEE PAGE 7-7 (VIDEO MISSING IN PLAY MODE) NO NO NO YES YES NO YES (VCR Section) CHECK IC301-61 OSD PICTURE MISSING CHECK IC301-65 CHECK IC6P01-19 CHANGE IC6P01 CHECK IC6P01-9, 10, [...]

7-9 PACE VCR IN STOP MODE BLUE MISSING IN STOP MODE CHANGE IC601 SELECT LINE MODE WITHOUT INPUT SIGNAL IC601-72 "H" CHECK IC6P01-8 TO IC601-72 NO YES YES CHECK IC6P01 IC6P01-9, 10, 11 (STB, CLK, DATA) CHECK IC601-6, 7, 8 NO YES IC6P01-8 "H" (SYNC JUDGE) VIDEO SIGNAL IC6P01-19 NO CHECK OSD VIDEO IN LINE YES YES NO (VCR Section) C[...]

7-10 MISSING AUDIO IC501-7, 69 AUDIO SIGNAL IC501-26 AUDIO FM CHECK CYLINDER CHANGE IC501 CHECK R815, R816, L809, L810, JC801 CHECK (AUDIO MISSING IN EE MODE) AUDIO MISSING IN REC MODE MONO HIFI MONO NO NO YES YES CHECK IC501 5V AND 9V LINE CHECK IC501-38, 39 (CLK, DATA) NO YES (VCR Section) CHECK Q3A03, Q3A02 CHECK R3A04 CHECK R373 IC301-15 AUDIO [...]

7-11 PLACE VCR IN STOP MODE AUDIO MISSING IN EE MODE CHECK C524, C525, R546, R547 CHECK IC501 CHECK TUNER BLOCK AND IC4N01 CHECK R517, R518, R509, R510 INPUT SELECT MODE IC501-7, 69 AUDIO SIGNAL INPUT IC501-51, 53 AUDIO SIGNAL INPUT NO LINE NO TUNER YES IC501-78, 80 AUDIO SIGNAL NO YES CHECK IC601 IC501-38, 39 CLK, DATA NO YES (VCR Section) CAPSTAN[...]

7-12 DRUM DOES NOT ROTATE PLACE THE VCR IN PLAY MODE CN604-8 12V CYL-SPEED IC601-18, 19 (8MHZ) CHECK CYLINDER MOTOR CHANGE XT601, C626, C627 CHECK D-PG, D-FG IC601-97 CHECK AL12V IN THE POWER BLOCK NO FASTER NO YES SLOWER YES (VCR Section)[...]

7-13 No focus incoming FE in SIC1-8 is within specified range? (FE Waveform) SIC3-27, 28 output are normal? Check open state from SIC3 to pick-up. Check RIC1 and A, B, C, D input. Check SIC3. Yes Yes No No A (DVD Section) No pick-up home positing SIC1-26 (SLD) output is normal? (1.7V ~ 1.8V) Check the Sled Motor and connection Check SIC1 Yes No SLE[...]

7-14 NO DVD LD ON RIC1-22 is 5V? Current exceeds 0.1A? LD out pick-up replace. Open check in related circuit. Check RIC1 Yes Yes Yes No No Divide RQ2 emitter terminal voltage and 5V real voltage difference into 10ohm. (DVD Section) No Search Operation MIRR , SIC1-37 output is normal? Actual velocity occurs at SIC1-152 terminal? Actual velocity occu[...]

7-15 FINE SEEK Check FINE SEEK MIRR signal (RIC1-67) is missing? TZCO signal (SIC1-159) is occurs? Track incomming is delayed? TE is within 2V and 3V? Pick-up transfer smooth. Check RIC1 Peripheral curcuit. Check SIC1 Peripheral curcuit. Time out due to many jump counts. Check SIC1 peripheral circuit. SIC1-14 (TRD) output is normal? SIC3-30, 29 (T+[...]

7-16 No Tray open/close ZIC1-24, 25 is Open ; "L" ? Close ; "H" ? Check SIC3-34, 35 output at OPEN /CLOSE Check signal line state from SIC3-34, 35 to tray motor. Check ZIC1 perpheral circuit. Check SIC3 perpheral circuit and CN3 connector. Yes Yes No No (OPEN Waveform) (DVD Section) CD/VCD/DVD L/R output error (Mixed Audio outpu[...]

7-17 S-Video output error Did the screen select with the s-video VIC1-28, 31 output is normal? Change a screen set Check the circuit of ZIC1, VIC1 Yes No No S-JACK output is normal? Check the connection between VIC1 and S-JACK Yes No Yes Check the connection of s-video cable (DVD Section) Y/Pr/Pb output error Did the screen select with the componen[...]

7-18E CVBS output error 27MHz clock input is normal at pin 161 in ZIC1? Analog output is normal at pin 170 in ZIC1? Check ZY1. Check the soldering of ZIC1. Yes Yes No No Analog signals are inputted normally VIC1-2? Yes No Power is normal at VIC1-1, 24, 34? Yes No Pin 5 in VIC1 is in high stste? Yes Check the connection netween pin 170 in ZIC1 and V[...]

8-1 8. REP AIR P AR TS LIST 8-1 Exploded Views - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-1-1 Cabinet Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-1-2 VCR Mechanical Parts (T op Side) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -[...]

8-2 8-1-1 Cabinet Assembly 8-1 EXPLODED VIEWS NO TE: • -XX, -X mean standardized parts, so they may hav e some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number[...]

8-3 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1 9-885-043-21 ASSY PANEL FRONT (D910B/D910E/D910N) 1 9-885-043-22 ASSY PANEL FRONT (D950B/D950E) 1 9-885-043-23 ASSY PANEL FRONT (D950GI) 1 9-885-043-24 ASSY PANEL FRONT (D910R) 1 9-885-043-25 ASSY PANEL FRONT (D910AZ) 2 9-885-037-27 DOOR TRAY 3 9-885-037-28 SPRING ETC[...]

8-4 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks B410 1-763-836-11 LOADING ASSY , MOTOR B440 3-075-253-01 SCREW ASSY MAC 2.6X5 B475 1-796-433-11 DAMPER CAPST AN B480 3-075-241-01 ASSY ACE HEAD G001 1-796-704-11 ASSY CL YNDER 6HD (SECAM) G060 3-075-254-01 SCREW ASSY MAC 3X6 G070 3-067-796-01 PLA TE-GROUND DECK G420 3-0[...]

8-5 8-1-3 VCR Mechanical Parts (Bottom Side) G542 B462 B560 B570 not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplie d not supplied not supplied not supplied not supplied not supplied not supplied not supplied B462 3-075-260-01 SCREW MAC 3X3 B560 1-796-432-11 MOTOR CAPST AN Ref. No. Pa[...]

8-6 8-1-4 DVD Mechanical Parts Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 900 3-078-592-01 SCREW T AP 2X6 903 9-885-037-07 SCREW MAC 1.7X3 904 9-885-037-08 SCREW T AP 1.7X5 H103 9-885-037-29 PULLEY GEAR H104 9-885-037-20 MOTOR LOADING ASSY H105 3-078-583-01 BEL T RECT ANGULAR H106 9-885-037-30 GEAR TRA Y H108 9-885-[...]

8-7 NO TE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX, and -X mean standardized parts, so they may hav e some difference from the original one. • RESISTORS All resistors are in ohms. MET AL: metal-film resistor MET AL O XIDE: Metal[...]

8-8 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks VCR MAIN Note : The components identified by mark 0 or dotted line with mark 0 are critical for saf ety . Replace only with par t number specified. D1SS17 1-804-412-11 DIODE FIT4 D1SS19 1-804-412-11 DIODE FIT4 ZD1P02 1-804-418-11 DIODE MTZJ12B ZD1P03 1-804-417-11 DIODE [...]

8-9 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < FUSE > 0 FZ01 1-576-729-11 FUSE-RADIAL LEAD1A 0 FZ02 1-576-729-11 FUSE-RADIAL LEAD1A 0 FZ03 1-576-729-11 FUSE-RADIAL LEAD1A 0 FZ04 1-576-729-11 FUSE-RADIAL LEAD1A < IC > DIC1 1-805-039-11 IC M74HCU04 IC301 1-804-702-11 IC (VIDEO) IC501 1-804-703-11 IC (HIF[...]

8-10E Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < VIBRA TOR > XT301 1-795-330-11 VIBRA TOR CRYST AL (4.433619MHz) XT601 1-795-332-11 VIBRA TOR CRYST AL (32.768kHz) (D910AZ/D910N/D910R) XT602 1-795-331-11 VIBRA TOR CRYST AL (8MHz) XT4N01 9-885-043-29 CRYST AL (18.432MHz) MISCELLANEOUS *************** 0 200 1-8[...]

— 162 — Sony Corporation Home Storage Company 9-929-774-11 2003H0500-1 ©2003. 8 Published b y Customer Suppor t Dept. SL V -D910AZ/D910B/D910E/D910N/D910R/ D950B/D950E/D950GI[...]