Snow Joe Saw Joe SWJ800E инструкция обслуживания

A Division of Snow Joe, LLC Model No. SWJ800E Form No. SJ-SWJ800E-880E © 2012 by Snow Joe, LLC All rights reserved. Original instructions. 1 SA VE THESE INSTRUCTIONS OPERA TOR’S MANUAL Electric Pole Chain Saw Electric Pole Chain Saw IMPOR T ANT! Safety Instruction All Operators Must Read These Instructions Before Use Always follow these safety g[...]

Extension Cords • Make sure your extension cor d is in good condition. When using an extension cord, be sur e to use one heavy enough to carry the current your pr oduct will draw . An undersized cord will cause a dr op in line voltage resulting in loss of power and overheating. T able 1 shows the correct size to use depending on cord length and n[...]

3 Kickback m W ARNING! Kickback may occur when the nose or tip of the guide bar touched an object, or when the wood closes in and pinches the saw chain in the cut. In some cases when the tip makes contact it may cause a fast reverse r eaction, kicking the guide bar up and back towards the operator . Pinching the saw chain along the top of the guide[...]

Know Y our Pole Chain Saw T echnical Data Rated V oltage 120V ~ 60Hz Motor 6.5 AMP Bar/Chain Length 8-IN T elescopic Shaft 67-IN -104-IN Maximum Cutting Diameter 8-IN Oil T ank Capacity 80 ml No Load Speed 6,000 rpm W eight 7 lbs 4 1. Bar Cover 2. Oil T ank Cap 3. Guide Bar (reversible) 4. Sprocket Cover 5. Sprocket Cover Bolt 6. Chain 7. Collar 8.[...]

Unpacking Carton Contents: • Corded pole saw body • Bar & chain • 7/32” Hex key wrench/ blade scr ewdriver • Bar cover • Safety and operating instructions Unpacking: 1. Carefully r emove the contents from the shipping carton. Make sure that all items listed in the carton contents ar e included. 2. Inspect the product car efully to m[...]

7. Install the sprocket cover (F) by inserting the r ear tab (G) (Fig. 1) rst into the rear tab slot (Fig. 2) and position the cover onto the saw head. 8. Install the sprocket cover bolt by hand and leave the bar free to move for tension adjustment (Fig. 4). 9. Remove all slack from the chain by turning the chain tensioner screw (Fig. 3) clockwi[...]

Using the Saw Adjusting T elescoping Pole (Fig. 7) 1. Rotate the collar counterclockwise to loosen (Fig. 7). 2. Push poles towards each other to shorten the pole or pull away from each other to lengthen the pole. 3. When you achieved the desired length, r otate the collar clockwise to secure. 4. Be certain you fully tighten the collars before opera[...]

• Now make your nishing cut from the topside of the branch smoothly and neatly against the main member so the bark will grow back to seal the wound. • Release the trigger ON/OFF switch as soon as the cut is completed. Failure to follow pr oper cutting procedur es will result in the bar and chain binding and becoming pinched or trapped in the[...]

Chain T ension Check the chain tension before using the saw when the chain is cold. The correct tension of a cold chain is when ther e is no slack on the underside of the guide bar , the chain is snug, but you can turn it by hand without binding. During normal saw operation, the temperature of the chain will increase. The drive links of a corr ectl[...]

Daily Checklist, Cleaning and Storing for your Pole Saw T o help maintain your Pole Saw for optimum performance, we recommend you follow this checklist each time you use your Pole Saw . m W ARNING! Do not plug in the power cord until you have completed all of the daily checks. INSPECT : Before plugging in the power cor d, inspect for any visible da[...]

11 NOTES[...]

A T wo-Y ear Full W arranty for r esidential use in the United States and Canada General Conditions: Snow Joe, LLC warrants this product to the original pur chaser for two years against defects in material or workmanship when used for normal residential purposes. Snow Joe, LLC will r epair any defect in material or workmanship, and repair or r epla[...]