Sears 26462_0 инструкция обслуживания

SF./_S OWNERS MANUAL Model No. 26462_0 CRAFTSMAN o PROFESSIONAL MID-SIZED ROUTER TABLE WARNING: Before operating product, read this manual and follow all its Safety and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates IL 60179 USA 26462 12/00 Printed in U.S.A. 4 9LCN- 84[...]

General Safety Instructions for Power Tools ................................................ 3 Additional Safety Instructions for Router Tables ......................................... 4 Introduction ........................................ . ......................................................... '...5 Optional Router Table Accessories ...[...]

SAFETY GUIDELINES- DEFINITIONS This manual contains informa- tion that is important for you to know and understand. This information relates to protect- ing YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you rec- ognize this information, we use the symbols to the right. Please read the manual and pay attention to these sections. IADANGER l [...]

18. Use recommended accessories Consult the owner's manual for recommended accessories and follow the instructions. The use of improper accessories may cause hazards. 19. Never stand on tool Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. DO NOT store materials above or near the tool making it[...]

switch box when turning the router ONor OFF. DO NOT touch anything but the switch box when doing this. NEVER reach under the router table for anyrea- son when therouter is running, except to turn it OFF. I A I 24.[ WARNING J Before making any cut, make sure the router is turned OFF, the router bit is not rotating, and the power cord is unplugged fr[...]

TOOLS REQUIRED • Phillips screwdriver. ° Small or medium sized adjustable wrench (or a set of nutdrivers). ° Electrical with 5/32" drill bit. • Hammer ROUTER TABLE 1. Position the router table top (Part No. 29LCN-981) as shown in Figure 1, with the bottom of the table top facing toward you. 2. Position the table legs (Part No. 29LCN-1283[...]

FIGURE 5 FIGURE 7 Front of--. Router Table #10-32 Hex "Keps"_ Nut, (Typical)_ -_,- _ / Router _ _ ,_/ / Table _,_ _ --///_ / Leg Switch_ "_ #10-32 518" Long Truss Head Machin Screw, (Typical) MOUNTING ROUTER TO THE ROUTER TABLE I WARNINGI ALWAYS UNPLUG ROUTER BEFORE MOUNTING. Craftsman Routers with Three-Hole and 6" Diame[...]

Other Brands of Routers It will be necessary for you to purchase a Craftsman Professional Router Adapter Plate, #25333, from your local Sears Retail Outlet, or through the Sears Catalogue. Routers with a total overall height of 13 inches or less, and a base diameter of 7 inches or less can be accommodated. m I NOTE I Because of vibration that occur[...]

4. Repeat steps 1 through 3 for the other side of the fence. 5. Make sure the adjustable jointing fence is inside the router table fence as far as it will go and that the clamping knob has been securely tightened. FIGURE 14 Fence Clamping Knob 114-20 x 1-3/4",ong II Round Head _./|l Square IL Neck Bolt / 9/32" LD. x 3/4" O.D. L_ / x[...]

I _'WARNINGI The vibrations from operating the router can, from time to time, cause the hex nut and the clamp plate to become loose on the clamp rod. PERIODICALLY CHECK THESE FASTENERS AND ALL FASTENERS to ensure that they are tight and secure. PUSH BLOCK ASSEMBLY TO THE ROUTER TABLE FENCE 1. Position the clamp plate relative to the push block[...]

surface before use. Failure to do so could cause the router table to tip over or slide, resulting in property damage and/or serious personal injury. 1. Set the router table on a workbench or other stable and sturdy surface. 2, While holding the router table in place, spot the loca- tion of the two mounting holes in each of the legs onto the workben[...]

GENERAL The power switch box is designed to be used with most Craftsman router tables. It provides the conven- ience of an "ON-OFF" switch box at the front of the table, thus eliminating the need to reach underneath the table to turn the router "ON" and "OFF". The power switch box also provides an optional simultaneous[...]

The switch box incorporates two positive features to prevent inadvertent switching on of the router and the unauthorized, and possibly hazardous, use by others. Inadvertent switching on of the router is prevented by the clear plastic switch box cover. The cover must be raised and the switch box manually toggled to the "ON" position to sta[...]

USING THE ROUTER TABLE The fence on your router table is provided as a guide to hold the work piece for accuracy in routing. I_I_WARNING] BEFORE each and every use, make sure the router table is SECURE on a work- bench and DOES NOT MOVE. ALIGNMENT OF UNITIZED FENCE TO MITER BAR SLOT 1. Line up the front of the fence with the "0" marks on [...]

section ADJUSTING DEPTH AND HEIGHT OFTHE CUT. Tightly secure the fence assembly and the router as described before. (MAKE SURE ROUTER IS UNPLUGGED WHEN MAKING ADJUSTMENTS.) 3. LOWER THE OVERHEAD GUARD to the operating position. (Overhead guard shown raised for reasons of clarity.) 4. Check you adjustments by turning the router "ON" using [...]

FIGURE 29 Fence Clamping Knob Fence Clamping Knob Fence.,. Clamping_ Knob', _crap Nood Adjustabk Jointing Fence flush with Router Table ' Piloted Router Bit Fence Overhead guard shown raised for reasons of clarity. FIGURE 30 Router Table Fence Work Piece Pilot Bearing rides against Router Pilot Bearing Piloted Router Bit "Work Piece [...]

Cutting Tenons 1. Make certain that the adjustable fence is locked in position with its face flush with the front face of the fence. 2. Mount the push block assembly on the fence, as described in the section PUSH BLOCK ASSEMBLY TO THE ROUTER TABLE UNITIZED FENCE. 3. Install the proper table top insert into the table top hole. 4. Mark line "A&q[...]

I I When cutting tenons, always clamp I NOTE the work piece with the end to be cut resting flat on the table top. This will minimize steps in the finished tenon surface due to variations in the table top flatness. See FIGURE 36 k Piece ////_ _" Previous cuts Figure 37. l I NOTE I Always cut full depth on all four J sides of tenon in one pass a[...]

PARTS LIST FOR CRAFTSMAN PROFESSIONAL MID-SIZED ROUTER TABLE MODEL NO. 26462 @ @ @ @ @@@ @ @ @@ @@@ @ @@ KEY! 1 2 '3 4 5 6 7 .-. 8 9 10 "-11 - "12 "13 _14 15 _16 17 _'- 18 _19 -"'- 20 PART NO. 29LCN-981 29LCN-1283 29LCN-996-1 29LCN-996-2 29LCN-996-3 29LCN-1255 29LCN-1019 29LCN-1018 29LCN-994 29LCN-758 29LCN-99[...]

TABLE ASSEMBLY FENCE ASSEMBLY U MISCELLANEOUS PARTS 2O[...]

MITER BAR ASSEMBLY @ PUSH BLOCK ASSEMBLY SWITCH ASSEMBLY 21[...]

When corresponding, always give the following information as shown in the list: Printed in U.S.A. 12/00 49LCN-84 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER: 26462 4. The ITEM NAME - PROFESSIONAL MID-SIZED ROUTER TABLE[...]