Samsung 901B инструкция обслуживания

Install drivers Install programs SyncMaste r 913N/915N/912T/913T/913B /901B[...]

Notational Failure to follow di rections noted by this symbol could resul t in bodily harm or damage to equipment. Prohibited Important to read and understa nd a t all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an ele c tri c shock Power When not used fo r extended perio d of time, set your comput[...]

Do not use a damaged or loo se plug. z This may cause an electric shock or fire. Do not pull the plug out by the w ire nor touch the p lug with wet ha nds. z This may cause an electric shock or fire. Use only a pr operly grou nded plug a nd receptac le. z An improper ground may cause el ect ric shock or equipment damag e. Insert the pow er plug fir[...]

Do not drop the monitor whe n moving it. z This may cause d amage to the prod uct or human bo dy. Install the monitor base in a sho w cas e or shelf so that the end of the base does not protr ude from the showc as e or shelf. z Dropping the product may cause dama ge to the product or personal injury. Do not place the product on an unstable or sm al[...]

Do not place the monitor face down. z The TFT-LCD surfac e may b e damaged. Installin g a wall bracket must be done by a qualifie d profession al. z Installation by unqua lified personnel may resu lt in injury. z Always use the mounting device specifi e d in the owne r's man ua l . When instal ling the pr oduct, make su re to keep it away from[...]

Unplug the pow er cord from the power outlet and wip e the product usin g a soft, dry cloth. z Do not use an y chemicals such as wax, benzene, alcohol , thinners, insecticide, air freshener, lu bri cant or detergent. Contact the Service Center or Customer Center for interior cleaning once a year. z Keep the prod uct's interio r clean. Dust whi[...]

Do not try to move the monitor by pu lling on ly the wire or the signal cable. z This may cause a breakdown, elec tri c shock or fire due to damage to the cable. Do not move the mo nitor right or le ft by pulling o nly the wire or the signal cable. z This may cause a breakdown, elec tri c shock or fire due to damage to the cable. Do not cover the v[...]

Adjust the r esolution an d frequency to th e levels ap propriate for th e model. z Inappropriate resolution may cau se undesirable picture quality. 19 inch (48 cm) - 1280 X 10 24 Watching the monitor continuously at a too close angle may result in eyesight damage. To ease eye strain, take at least a fiv e-minu te break after every hour of using th[...]

Please make su re the followi ng items are in cluded with your mon itor. If any items are missing, co ntact your dealer . Contact a local deale r to bu y o p tional item s. Unpacking Option 1 Monitor & Sim p le stand Bottom MagicRotation™ prog ram can not be provided as Simple Stand does not support Pivot function. Option 2 Monitor & Pivo[...]

Quick Setup Gu ide Warranty Car d (Not available in al l locations) User's Guide, Monitor Driver, Natural Color software, MagicTune™ soft ware, Ma g icRotation software Cable D-Sub Cable Power Cord Front 1. Menu button [ ] Opens the OSD menu. Also use to ex it the OSD menu or return to the previous menu. 2. MagicBright bu tton [] MagicBright[...]

depending on your taste. If this is the case, adjust th e brightness and contrast by using the OSD menu. 2) Text : Normal brightness For documentations or works invol ving heavy text. 3) Internet : Medium brightness For working w ith a mixture of i mages such as text and graphics. 4) Entertain : High brightness For watchin g motion pictures su ch a[...]

For usin g a lockin g device, contact where y ou p urchase i t. See Connecting the Mon it or for further information re garding cable connections.[...]

Please make su re the followi ng items are in cluded with your mon itor. If any items are missing, co ntact your dealer . Contact a local deale r to bu y o p tional item s. Unpacking Option 1 Monitor & Sim p le stand Bottom MagicRotation™ prog ram can not be provided as Simple Stand does not support Pivot function. Option 2 Monitor & Pivo[...]

Quick Setup Gu ide Warranty Car d (Not available in al l locations) User's Guide, Monitor Driver, Natural Color software, MagicTune™ soft ware, Ma g icRotation software Cable D-Sub Cable Power Cord Sold se p aratel y DVI Cable Front 1. Menu button [ ] Opens the OSD menu. Also use to ex it the OSD menu or return to the previous menu.[...]

2. MagicBright bu tton [] MagicBright is a new feature pr oviding optimum viewing environment dependi ng on the contents of the image you are watching. Currently four differe nt mode s are available: Custom, Text, Internet, and Entertain. Each mode has its own pre- configured brightness value. You can e asily select one of four settings by simpl y [...]

(The configu ration at the bac k of the monitor may vary from produ ct to product.) 1. Power port Connect the power cord for your monitor to the power port on the b ack of the monitor. 2. DVI port Connect the DVI cable to the DVI port o n the back of your Monitor. 3. D-sub 15-pin po rt Connect the D-sub cable to the 15-pin, D - sub co nnector on th[...]

1. Connect the power cord for your monitor to the power port on t he back of the m onitor. Plug the power cord fo r the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) conne c to r on the video card. Connect the D-sub cable to the 15-pin, D-sub connector on the back of your moni tor. 2-2. Connected to a Macintosh. Connect the monitor to[...]

Monitor and Bo tt om Pivot Stand A . Stand Stoppe r Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.[...]

Simple st and Pivot stan d A. Monitor B. Mounting interface pad 1. Turn off your monitor and unplu g its po wer cord . 2. Lay the LCD monitor face-dow n on a flat surf ace with a cush ion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting in terface pad with the hole s in th[...]

4. Click the "Install" button i n the "Warning" window. 5. Monitor d river installation is completed. Windows XP/20 00 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose you r monitor model in the model list, then cl ick the "OK" button. 4. If you can see following messa ge window[...]

Installin g the Monitor Driver ( Manual ) Windows XP | Windows 2000 | Windows Me | Wind ows NT | Linux When prompte d by the operating sys tem fo r the monitor driver, insert the CD-ROM included with this moni tor. Driver installation is slight ly diff erent from one operating system to ano ther. Follow th e directions approp riate for the operatin[...]

5. Click " Update Driver.. " and select " Install from a list or.. " then click " Next " button. 6. Select " Don't search ,I will.. " then click " Next " and then click " Have disk ". 7. Click the " Browse " button then choose A: (D:Driver) and choose your monitor model in [...]

10. Monito r driver installatio n is comple ted. Microsoft ® Window s ® 2000 Operating System When you can see "D ig ital Signature Not Found" on your monitor, follow the se steps. 1. Choose " OK " button on the " Insert disk " w indow. 2. Click the " Browse " button on the " File Needed " window.[...]

Microsoft ® Window s ® NT Oper ati ng System 1. Click Start , Settings , Control Panel , and then double-click Display icon. 2. In Display Regi stration Information win dow, click Settings Tab an d th en click All Display Modes . 3. Select a mode that you wish to use (Resolutio n, Number of colo rs and Vertical frequency) and then click OK . 4. C[...]

For more information, re fer to Help (F1) in the software prog ram. How to install the Natural Co lor software Insert the CD included with the Samsun g mon itor into the CD-ROM Drive. Th en, the initial screen of the prog ram Natural Color w ill be execute d. Click Natural Color on the initial scre en to install the Natura l Co l or soft wa re . To[...]

1. Connect the power cord for your monitor to the power port on t he back of the m onitor. Plug the power cord fo r the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) conne c to r on the video card. Connect the D-sub cable to the 15-pin, D-sub connector on the back of your moni tor. 2-2. Using the DVI (Digital) connector on th e video [...]

Monitor Assembl y Monitor and Bo tt om Pivot Stand A . Stand Stopper Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.[...]

Simple st and Pivot stan d A. Monitor B. Mounting interface pad 1. Turn off your monitor and unplu g its po wer cord. 2. Lay the LCD monitor face-dow n on a flat surf ace with a cush ion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting in te rface pad with the holes i n th[...]

4. Click the "Install" button i n the "Warning" window. 5. Monitor d river installation is completed. Windows XP/20 00 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose you r monitor model in the model list, then cl ick the "OK" button. 4. If you can see following messa ge window[...]

Installin g the Monitor Driver ( Manual ) Windows XP | Windows 2000 | Windows Me | Wind ows NT | Linux When prompte d by the operating sys tem fo r the monitor driver, insert the CD-ROM included with this moni tor. Driver installation is slight ly diff erent from one operating system to ano ther. Follow th e directions approp riate for the ope rati[...]

5. Click " Update Driver.. " and select " Install from a list or.. " then click " Next " button. 6. Select " Don't search ,I will.. " then click " Next " and then click " Have disk ". 7. Click the " Browse " button then choose A: (D:Driver) and choose your monitor model in [...]

10. Monito r driver installatio n is comple ted. Microsoft ® Window s ® 2000 Operating System When you can see "D ig ital Signature Not Found" on your monitor, follow the se steps. 1. Choose " OK " button on the " Insert disk " w indow. 2. Click the " Browse " button on the " File Needed " window.[...]

Microsoft ® Window s ® NT Oper ati ng System 1. Click Start , Settings , Control Panel , and then double-click Display icon. 2. In Display Regi stration Information win dow, click Settings Tab an d th en click All Display Modes . 3. Select a mode that you wish to use (Resolutio n, Number of colo rs and Vertical frequency) and then click OK . 4. C[...]

For more information, re fer to Help (F1) in the software prog ram. How to install the Natural Co lor software Insert the CD included with the Samsun g mon itor into the CD-ROM Drive. Th en, the initial screen of the prog ram Natural Color w ill be execute d. Click Natural Color on the initial scre en to install the Natura l Co l or soft wa re . To[...]

AUTO SyncMaste r 913N/915N 1. [ ]Use this button to ope n the on-screen menu and exit from the men u scree n or close screen adjustment menu. 2. [ ]This button all ow s you to adj ust it ems in the menu. 3. [ ]This button all ow s you to adj ust it ems in the menu. 4. [ ]Press this button to activate a highlighted menu item. 5. [ AUTO ]Press to sel[...]

Menu Descripti on AUTO When the ' AUTO ' butto n is pressed, the auto adjustment screen appears as shown in the animated scree n on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coa r se an d position are adjusted automati cally. To make the au tomatic adju stment function [...]

Brightness Menu Descripti on Brightness When OSD is not on the screen, push the button to ad jus t brightness. 1. Picture Brightness Contrast 2. Color Color Tone Color Control Gamma 3. Image Coarse Fin e Sharpness H-Position V-Position 4. OSD Languag e H-Position V-Position Transparency Display Time 5. Setup Image R eset Color Reset 6. Information [...]

Menu Description Pl ay/Stop Brightness You can use the on-screen menu s to change the brightness according to perso na l preference. Direct Acce ss Feature : When OSD i s not on the s creen, Push the button to adj ust brig htn ess. Contrast You can use the on-screen me nus to change the contrast according to personal pre ference. Color Menu Descrip[...]

Gamma Select one of three pre-de fi ne d ga mmas. z Mode 1 : Shows normal gamma z Mode 2 : Shows high er ga mma(brighter) z Mode 3 : Shows lo wer gamma(darker) Image Menu Description Pl ay/Stop Coarse Removes noise such as ve rtical stripes. Coarse adjustment may move the screen image area . You may relocate it to the cen te r usin g the Horizontal[...]

Menu Description Pl ay/Stop Languag e Change the langua ge used in the menu. You can cho ose one of the se ven language s. Note :The language chose n affects only the language o f the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monit or. V-Positi[...]

Menu Description Pl ay/Stop Image Reset Image parameters are replaced with the factory d efau lt values. Color Reset Color parameters are repl ace d with the factory default values. Information Menu Descripti on Informatio n Shows a video source, display mode on the OSD screen.[...]

AUTO SyncMaste r 912T/913T/913B /901B 1. [ ]Use this button to ope n the on-screen menu and exit from the men u scree n or close screen adjustment menu. 2. [ ]This button all ow s you to adj ust it ems in the menu. 3. [ ]This button all ow s you to adj ust it ems in the menu. 4. [ ]Press this button to activate a highlighted menu item. 5. [ AUTO ]P[...]

Menu Descripti on AUTO When the ' AUTO ' butto n is pressed, the auto adjustment screen appears as shown in the animated scree n on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coa r se an d position are adjusted automati cally. (Available in ana log mode only) To make the[...]

- four different modes(Cust om/Text/Internet/Entertain) Brightness Menu Descripti on Brightness When OSD is not on the screen, push the button to ad jus t brightness. SOURCE Menu Descripti on SOURCE Selects the video si gnal while the OSD is off. 1. Picture Brightness Contrast[...]

2. Color Color Tone Color Control Gamma 3. Image Coarse Fin e Sharpness H-Position V-Position 4. OSD Languag e H-Position V-Position Transparency Display Time 5. Setup Auto Source Image Reset Color Reset 6. Information Picture Menu Description Pl ay/Stop Brightness You can use the on-screen menu s to change the brightness according to perso na l pr[...]

Menu Description Pl ay/Stop Color Tone The tone of the color can be changed an d one of four modes can be selected - Cool , Normal, Warm and Custom. Color Control Adjusts individual R,G,B color balance. Gamma Select one of three pre-de fi ne d ga mmas. z Mode 1 : Shows normal gamma z Mode 2 : Shows high er ga mma(brighter) z Mode 3 : Shows lo wer g[...]

Coarse adjustment may move the screen image area. You may relocate it to the cente r usin g the horizontal control menu. (Available in ana log mode only) Fine Removes noise such as horizo ntal stripes. If the noise persists even after fine tuning , rep eat it after adjusting the frequency (clock speed). (Available in ana log mode only) Sharpness C [...]

You can set the amount of time the menu will wait be fo re it is turned off. Setup Menu Description Pl ay/Stop Auto Source Select Auto Sourc e for the monitor to automatically select the signal source. Image Reset Image parameters are replaced with the factory d efau lt values. Color Reset Color parameters are repl ace d with the factory default va[...]

Menu Descripti on Informatio n Shows a video source, display mode on the OSD screen.[...]

Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubl eshooting Overview What is MagicTune™? Monitor performance can vary due to the graphics card, host computer lighti ng conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, [...]

Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Installation 1. Insert the install ation CD into the CD-ROM drive. 2. Click th e MagicT une™ insta llation fil e. 3. Select installation Language, Click "Next". 4. When the InstallationShield Wizard window appears, click "Next." 5. Select &quo[...]

6. Choose a folder to install the MagicTune™ program. 7. Click "Install." 8. The "Installation Status" window appears.[...]

9. Click "Finish." 10. When th e insta llation is complete , the Mag icTune ™ executable icon appears on your desk top. Double-click the icon to start the program. Installation Problems The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment. See "Troubleshooting&q[...]

OS z Windows™ 98 SE z Windows™ Me z Windows™ 2000 z Windows™ XP Home Edition z Windows™ XP Professional Hardware z 32MB Memory above z 25MB Hard disk space above * For more information, visit the MagicTune™ website . It is recommended using MagicTune™ in Windo ws™ 2000 or later .[...]

Overview | Installation | OSD Mode | Color Calibration | Uninstal l | Troubleshooting OSD Mode The OSD mode makes the adjustment of settings on all monitors easy. When selected , each tab on top of the control window displays the general descriptions of the sub-menu items for adjustment. When selected, each tab displays a list of menus. For quick a[...]

Picture Tab Definition Allows the user to adjust the scr een settings to the d esired values. Color Tab Definition Adjusts the "warmth" of the m onitor background or image color. Brightness Contrast Re solution MagicBright n m l k j i n m l k j n m l k j n m l k j Brightness Makes the entire sc re en brighter or darker. The detailed data [...]

Image Tab Definition Adjusts the Fine , Coarse and Position values. Color Tone C olor Control C alibration n m l k j i n m l k j n m l k j Color Tone The tone of the color can be changed. z Warm - Normal - Cool z Custom Color Control Adjusts of th e monitor im age color. You can change the monitor color t o your desired color. z R- G - B Calibratio[...]

Option Tab De finition You can configure MagicTune™ using the foll owing options. Image Set up Positi on n m l k j i n m l k j Image Setup z Fine : Removes noise such as horizontal stripes. If the noise persists even after Fi ne tuni ng, repeat it after adjusting the frequency (clock speed). z Coarse : Removes noise such as vertical stripes. Coar[...]

Support Tab Definition Shows the Asset ID and the version nu mber of th e pr ogram, and allows you to use the Help feature. Preferences z Enable task tray m enu . - To access the MagicTune™ menus, click the icon on the [task tray menu]. The menus are not displayed if the [E nable System Tray] is deselected in [Options] ' [Basic Settings]. z [...]

[...]

Overview | Installation | OSD Mode | Color Calibration | Uninsta ll | Troubleshooting Color Calibration 1. Color Calibration Color Calibration guides you to get opti mal color condition for your monit or. Proceed follow ing 5ste ps for ge tting o ptimal mo nitor c olor cond ition . 1. Control "Brightness control bar" for matching t he bri[...]

Press "Preview" button on the Color Calibration. The above picture will be shown. 1. Press "View Calibrated " button to see th e calibration effect which you adjusted. 2. Press "View Uncalibrated" button to see the original imag e.[...]

Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Uninstall The MagicTune™ program can be removed only by us ing the "Add or Remove Programs " option of the Windows™ Control Panel. Perform the following steps remove MagicTune™. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Contr[...]

Overview | Installation | OS D Mode | Color Calibration | Uninsta ll | Troubles hooting Troubleshooting The current compu ting system is no t compatible wi th MagicTune™. Please press OK a nd click on the "Sh ortcut to the MagicT une™ site" to vi ew our home page for further ref erence. An error ma y occur when your video/g raphic car[...]

Visit the v ideo card make r's homepa ge and download and install the latest driver. For more i nformati on about the vi deo card, c ontact the card manuf acturer. To ensure nor mal operation , please rest art your system . An error occurs when the system is not restarte d after installing MagicTune™. (This is for W in98SE and W inMe only.) [...]

z Visit the M agicTune™ website for technical support for MagicTun e™, FAQs (questions and an swers) and software upgrades. z Visit the M agicTune™ website and download the installation software for MagicTune™ MAC. the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/mon itor/magicTu[...]

Overview | Installation | Interface | Uninstall | Troubleshoo ting Overview What is Magi cRotation? Traditionally, computer displays allowed the user to view only in landscape mode. In today's information age, more users need to view do cuments, web pages, emails, etc. in there day to day life. These types of applications ca n be better viewed[...]

Overview | Installation | Interfa ce | Uninstall | Troubleshooting Installation 1. Insert the install ation CD into the CD-ROM drive. 2. Click the Magi cRotatio n instal lation f ile. 3. Select installation Language, Click "Next". 4. When the InstallShiel d Wizard window appears, click "Next." 5. Select "I agree to the ter [...]

6. Choose a folder to install the MagicRotation program. 7. Click "Install." 8. The "Installation Status" window appears.[...]

9. Click "Finish." Have to reboot the system in order fo r the MagicRotation to work properly. 10. When th e insta llation is complete , the Mag icRotat ion executable icon appears on your des ktop. Installation Problems The installation of MagicRotation can be affected by the factors such as vide o card, motherboard and the network envir[...]

{ Close the application. { Select the Orientation (90, 180, 270) you want to view the application. { Relaunch the applicati on. In most cases this should fix the problem. 3. User Applications using OpenGL and DirectDraw (3D drawing) will not function as per the orie ntation mode selected (90, 180, 270 ). e.g. 3D games 4. DOS ba sed app lication s i[...]

Ov ervi ew | Ins t all a t i on | Interfa ce | Uni ns ta ll | Troubleshooting z When Rotation is functioning, portion of MagicTune™ p rogram may not op erate no rmall y. z Au toRota tion : T he screens di splay wi ll au tomat ically rota te when the moni tor is rotate d. To ex ecu te Auto Rot ati on, i t s houl d b e don e as be lo w. z P lease i[...]

Rota te t o 90 : Dis p lay will be rot ate d 9 0 de gr ees fr om t he cur re nt an g le. Rota te t o 180 : Di splay wi ll b e rotated 180 degre es from the curren t angl e.[...]

Rota te t o 270 : Di splay wi ll b e rotated 270 degre es from the curren t angl e. Hot k ey : H ot Keys are availab le b y defaul t and can b e change d by us er. It can be assig ned by use r directly with k eyboard af ter changin g the existing HotKey . User can create the hot key with the comb ination of Sh ift, Ctrl, Alt and gene ra l keys. I n[...]

[...]

Overview | Installation | Interface | Uninstall | Troubleshoo ting Uninstall The MagicRotation program can be removed only by using the "Add/Remove Programs" option of the Windows™ Control Panel. Perform the following steps to remove MagicRotation. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the m[...]

Overview | Installation | Interf ace | Uninstall | Troub leshooti ng Troubleshooting Before You Call Technical Support z MagicRotat ion Software work s with the insta lled "Display Driver" supplied by your Graphic Card Vendor to provide screen rotation capabilities. If the installed "Display Driver" is working incorrectly or has[...]

Before calling for servic e, check the information in thi s section to see if you can remedy any problems yourself. If you do need assistance , please call th e phone number on th e Information section or contact your de al er . Symptom Check List Solutions No images on the screen. I cannot turn on the monitor. Is the power cord connected properly?[...]

mode duri ng this one -minute peri od. (The message is displ aye d again if the system is rebooted.) There is no image on th e screen. Is the pow er indicator on the monitor blinking at 1 second intervals? The monitor is in PowerS aver mod e. press any key on the keyboard to activate the monitor and restore the image on the screen. The screen shows[...]

monitor' by searchi n g ne w Hardware. MagicTune i s an additi onal software for the monito r. So me graphic cards may not support yo ur monitor. When you have a problem with the gra phi c card, visit our webs ite to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune MagicTune™ doe sn't work proper[...]

Self-Test Featu r e Che ck | Warning Messages | Environment | Useful Tips Y our monitor provides a s elf test featur e that allow s you to chec k whether your monitor is functioni ng properly . Self-Test F eature Check 1. Turn off both yo ur computer an d the monitor. 2. Unplug the vi deo cable from the back of the computer. 3. Turn on the monitor.[...]

Before calling for servic e, check the information in thi s section to see if you can remedy any problems yourself. If you do need assistance , please call th e phone number on th e Information section or contact your de al er . Symptom Check List Solutions No images on the screen. I cannot turn on the monitor. Is the power cord connected properly?[...]

85Hz, the display will work prop erl y but the "Not Optimum Mode","Recommand ed Mode 1280 x 1024 60Hz" message appears for one minute and the n disappears. Please change to the recommended mode duri ng this one -minute peri od. (The message is displ aye d again if the system is rebooted.) There is no image on th e screen. Is the[...]

have changed after changing the v ideo card. Has the video card been set properly? Set the video card by referring to the video card manual. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have you installed the monitor driver? Install the monitor driv er acco rdi n g to the Driver Installat[...]

manual for de tails.) How can I adjust the re solution? Windows ME/XP/2000 : Se t the resolution at the Control Panel → Display → Settings. * Contact the video card manufacturer for deta il s. How can I set the Power Saving function? Windows ME/XP/2000 : Set the fu nction at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Comp[...]

The location an d th e position of the mo ni tor may influenc e the quality and o t her features of the monitor. 1. if there are any sub woof er spea kers near the monitor, unplug and reloca te the woofer to anothe r room. 2. Remove all electronic devices such as ra dios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor[...]

General General Model Name Sync Master 913N LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Type a-si TFT acti ve matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,2M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution[...]

Less than 38W Dimensions (WxDxH)/ Weight ( Simple Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 215. 2 x 424.6 mm / 16.4 x 8.5 x 16. 7 inch(With Basi c Stand) / 5. 6 kg Dimensions (WxDxH)/ Weight ( Pivot Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 200. 0 x 420.6 mm / 16.4 x 7.9 x[...]

Preset Timing Modes If the signal transferred from the comp uter is th e same as the following Preset Timing Modes, the screen will be adjusted automa tically. However, if the signal differs, the screen may go blank whi le the power LED is on. Re fer to the video card manual and adjust the scree n as follows. Table 1. Prese t Timing Modes Display M[...]

General General Model Name Sync Master 915N LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Type a-si TFT acti ve matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,2M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution[...]

Less than 38W Dimensions (WxDxH)/ Weight 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 215. 2 x 424.6 mm / 16.4 x 8.5 x 16. 7 inch(With Basi c Stand) / 5. 6 kg VESA Mounting Interface 100mm x 100mm (for use with Spec ialty(Arm) Mounti ng hardware.) Environmen tal consider ations Operating Temperature : 50°F ~ 104°F(10°[...]

If the signal transferred from the computer is t he sa me as the following Preset Timing Modes, the screen will be adjusted automa tically. However, if the signal differs, the screen may go blank whi le the power LED is on. Re fer to the video card manual and adjust the screen as follows. Table 1. Prese t Timing Modes Display Mode Horizontal Freque[...]

General General Model Name Sync Master 912T LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Type a-si TFT acti ve matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16, 7 M C o l o rs Resolution Optimum resolution 1280 x 1024@60 Hz Maximum reso[...]

Less than 38W Dimensions (WxDxH)/ Weight 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 200. 0 x 420.6 mm / 16.4 x 7.9 x 16. 6 inch(With Basi c Stand) / 7. 2 kg VESA Mounting Interface 100mm x 100mm (for use with Spec ialty(Arm) Mounti ng hardware.) Environmen tal consider ations Operating Temperature : 50°F ~ 104°F(10°[...]

Preset Timing Modes If the signal transferred from the comp uter is th e same as the following Preset Timing Modes, the screen will be adjusted automa tically. However, if the signal differs, the screen may go blank whi le the power LED is on. Re fer to the video card manual and adjust the scree n as follows. Table 1. Prese t Timing Modes Display M[...]

General General Model Name Sync Master 913T LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Type a-si TFT acti ve matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,2M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution[...]

Less than 38W Dimensions (WxDxH)/ Weight ( Simple Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 215. 2 x 424.6 mm / 16.4 x 8.5 x 16. 7 inch(With Basi c Stand) / 5. 6 kg Dimensions (WxDxH)/ Weight ( Pivot Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 200. 0 x 420.6 mm / 16.4 x 7.9 x[...]

Preset Timing Modes If the signal transferred from the computer is t he sa me as the following Preset Timing Modes, the screen will be adjusted automa tically. However, if the signal differs, the screen may go blank whi le the power LED is on. Re fer to the video card manual and adjust the scree n as follows. Table 1. Prese t Timing Modes Display M[...]

General General M o d e l N a me Sy n c Mas t er 9 1 3B / 901B LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Type a-si TFT acti ve matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,2M Colors Resolution Optimum resolution 1280 x 1024@60 Hz[...]

Less than 38W Dimensions (WxDxH)/ Weight ( Simple Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 215. 2 x 424.6 mm / 16.4 x 8.5 x 16. 7 inch(With Basi c Stand) / 5. 6 kg Dimensions (WxDxH)/ Weight ( Pivot Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 200. 0 x 420.6 mm / 16.4 x 7.9 x[...]

Preset Timing Modes If the signal transferred from the computer is t he sa me as the following Preset Timing Modes, the screen will be adjusted automa tically. However, if the signal differs, the screen may go blank whi le the power LED is on. Re fer to the video card manual and adjust the scree n as follows. Table 1. Prese t Timing Modes Display M[...]

Service The address an d p hone number o f the com p an y can be chan g ed without p rior notice. CANADA : Samsung Electronics Cana da Inc., Cust omer Service 55 Standish Co urt Mississauga, Ontario L 5R 4B2 Canada Tel. 1-800 -SAMSUNG (7267 864) Fax. (905) 542-1 199 http://www.samsung. ca MEXICO : Tel. 01-800-SA MSUNG (7267864 ) Fax. 01.800.84 9.17[...]

Tel. 0800 -124-421 http://www.samsung. com/br CHILE : Samsung Electron ics Chile LTDA. A vda. Americo V espucio Sur 100 , Oficina 10 2 Las Condes, Sa ntiago, Chile Tel. 800-726 -7864(SAMSUNG) Fax. 56-2-485 -8502 http://www.samsung. com/cl COST RICA : Tel. 0-800 -507-7267 http://www.samsung. com/latin ECUADOR : Tel. 1-800 -10-7267 http://www.samsung[...]

Tel. 38 32 2 887 http://www.samsung. com/dk FINLAND : Tel. 09 69 3 79 554 http://www.samsung. com/fi FRANCE : Samsung Service Cons o mm ateurs 66 rue des Vanesses BP 50116 - Vi llepinte -95950 ROISSY cedex Franc e Tel. 08 25 0 8 65 65 (0,15 /min) Fax. 01 48 63 06 38 (0,15 /min) http://www.www.sa msung.fr GERMANY : Samsung Electronics GmbH Samsung H[...]

POLAND : Tel. 0 801 801 881 Fax. +48-22-607 4448 http://www.samsung. com/pl PORTUGAL : SAMSUNG ELECTRONICA PORTUGUESA, S.A Rua Cesario Ve rde, no 5-4, Pis o 2795-753 Queija s-Portugal Tel. 80 8 200 128 http://www.samsung. pt SLOVAKIA : Tel. 0850 123 989 SPAIN : Tel. 902 1 0 11 30 http://www.samsung. com/es SWEDEN : Tel. 08 58 5 367 87 http://www.sa[...]

Tel. 800-810 -5858, 010 - 6475 1880 http://www.samsungservice.com.cn HONG KONG : Customer Serv ice Center 11/F, Phas e 2, MTL warehou se Building, Berth One, Kwai Chun g, N.T., Ho n g Kong Tel. 2862 6001 Fax. 2862 69 71 http://www.samsung. com/hk INDIA : 2nd fl CC-28 , Ne hru Enclave Kalka ji New Delhi Indi a 110019 Tel. 3030 8282 1600 1100 11 http[...]

TAIWAN : Tel. 0800 -329-999 http://www.samsung. com/tw VIETNAM : Tel. 1 800 588 889 Fax. (084) 08-8965566 http://www.samsung. com/vn SOUTH AFRICA : Samsung Electronics South Africa (PTY) LTD Unit 5/6, Hi Tech Villiag e, Superior R oad, Midran d South Afric a Tel. 0860 72 6786 (SAMSU NG) Fax. 27-11-5 4 5-6112 http://www.samsung. com/za U.A.E : Tel. [...]

For Better Display 1. Adjust computer resolutio n and screen i njection rate (refresh rate) on computer as described belo w to enjoy the best quality of pictu re. You can have a n uneven qual ity of picture in th e screen if the best quality of picture is n ot provided in TFT-LCD . { Resolution: 1280 x 102 4 { Vertical f requency (ref resh rate): 6[...]

PRODUCT INFORMATION (I mage Retention Free) LCD Monitors and TVs may have image retentio n when switching from one image to an othe r especially after displaying a statio nary image for a long time. This guide is to demonstrate corre ct usag e of LC D products in order to protect them from Image retention. What is Ima g e retention ? During normal [...]

The best way to prote ct your monitor from Ima ge retention is to s et yo ur PC or S y stem to o p erate a Screen Saver p ro g ram when y ou are not usin g it. Image retention may not o ccur when a LCD panel is opera te d un der normal conditions. Normal conditions are defined as continuously changing vi deo patterns. When the LC D panel is operate[...]

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate col lection systems) This marking shown on t he product or its literature, indicates that it sho uld not be dispose d with other hous ehold wastes a t the end of it s working li fe[...]