Samsung 7100 инструкция обслуживания

Ed. 00 Of ficeSer v 7100 Call Ser v er Pr og r amming Guide[...]

COPYRIGHT This guide is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright. No information contained herein may be copied, translated, transcribed or duplic ated for any commercial pur- poses or disclosed to the third p arty in any form w ithout the prior written consent of SAMSUNG Electronics Co., Ltd. TRADEMARKS is the tra[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications I INTRODUCTION Purpose This guide describes a programming method for the Of ficeServ 7100 system users. OfficeServ 7100 allows you to utilize a digital phone to sim ply change the system setup. Likewise, using a phone to change the sy stem setup is called MMC(Man Machine[...]

Ошибка ! Стиль не определен . II Samsung Business Communications Conventions The following types of paragraphs contain speci al information that must be carefully read and thoroughly understood. Such information ma y or may not be enclosed in a rectangular box, separating it from the main text, but is al ways preceded by an ic[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications III Reference Guides The following guides are also provided with your OfficeServ 7100 system. OfficeServ 7100 Install ation Guide Describes the installation procedures and sp ecifications for the OfficeServ 7100 system. OfficeServ 7100 General Description Describes the b[...]

Ошибка ! Стиль не определен . IV Samsung Business Communications This p age is intentionally left blank.[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications V SAFETY CONCERNS For product safety and correct operation, the following information must be given to the operator/user and shall be read before the installation and operation. Symbols Caution Indication of a general caution Restriction Indication for prohibiting an act[...]

Ошибка ! Стиль не определен . VI Samsung Business Communications Warning Caution Before using the Auto Record feature Before using the Auto Record feature, ma ke sure that you are not violating any laws. Samsung is not responsible for any i llegal use of this feature. Caution CALL COST(MMC 508) Changing this value w hen there [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications VII T ABLE OF CONTENTS INTRODUCTION I Purpose ........................................................................................................................ ...................I Audienc e .........................................................................[...]

Ошибка ! Стиль не определен . VIII © SAMSUNG Electronics Co., Ltd. 1.6.7 Diagnosis F unction ........................................................................................................1-27 1.6.8 Hotel Func tion .......................................................................................................[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications IX [209] ASSIGN ADD- ON MODUL E .............................................................................................2-54 [210] CUSTOMER ON/OF F PER TENA NT ...............................................................................2-55 [21 1] DOOR RING ASSIG[...]

Ошибка ! Стиль не определен . X © SAMSUNG Electronics Co., Ltd. [412] ASSIGN TRUNK SIGNAL ............................................................................................... 2-1 12 [414] MPD/PR S SIGN AL ......................................................................................................... 2- 11[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications XI [606] ASSIGN SPEED BLOCK ................................................................................................2-177 [607] UCD OP TIONS .............................................................................................................. .2-179 [608[...]

Ошибка ! Стиль не определен . XII © SAMSUNG Electronics Co., Ltd. [750] VM CARD REST ART ......................................................................................................2-24 6 [751] ASSIGN MAILBOX ..........................................................................................................2 [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications XIII [835] MGI DSP OP TIONS ........................................................................................................2- 307 [836] H.323 GK OPTIONS .......................................................................................................2- 310[...]

Ошибка ! Стиль не определен . XIV © SAMSUNG Electronics Co., Ltd. LIST OF FIGURES Figure 1.1 24B LCD DCS Euro Ph one ..................................................................................... 1-2 Figure 1.2 DS- 5038S Phone .............................................................................................[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-1 CHAPTER 1. Overview of MMC Pro- gramming In this chapter , the things to know befor e you start MMC programming, and the phone but- tons and cautions will be discussed. 1.1 Introduction to Programming The MMC means the changes on the data that is used for the system [...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-2 Samsung Business Communications 1.2 Digital Phones Y ou need a digital display(LCD) phone in order to car ry out programming. These include DCS Euro keysets and DS/ITP 5000 Series key sets, and some examples are described in the following sections. All use special programmi ng butto[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-3 The special buttons are referred to within th e relevant MMCs. For example, button ‘A ’ is used to toggle between uppercase and lowerc ase characters when entering text on the dis- play . All programmable buttons can be prog rammed with functions as required. The[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-4 Samsung Business Communications Figure 1.3 DS/ITP-5014D/5021D Phone Microphone DS/ITP-5014D (Programmable Buttons: 14) DS-/ITP5021D (Programmable Buttons: 21) Soft Buttons Transfer Button Programmable Buttons Scroll Button Telephone Status Indicator Conference Button Redial Button V[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-5 Figure 1.4 DS-5014S/5007S Phone The DS/ITP-5000 series phones have 38, 21, 14 or 7 programmable buttons that can be programmed with functions. Also, there are sever al other function buttons: the dial buttons, the volume control buttons , the redial button that allow[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-6 Samsung Business Communications Using large LCD Phones Large LCD phones(DS/ITP-501 2L) do not have programmable b uttons. Instead, they display programming functions o n the LCD to be selected via the selection buttons. Refer to your keyset user guide for more i nfor- mation. 1.3 Ca[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-7 1.4 Program List by User’s Level The MMC program can be divided into pr ogrammable one and non -programmable one. The programmable MMC is classified into 3 levels, such as technician, operator , and sta- tion level. In this section, the programma ble MMC for each l[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-8 Samsung Business Communications 1.4.2 Operator Level Programming A technician can do programming within the range set by the MMC [802] CUSTOMER ACCESS MMC NUMBER. Programming is allowed for any phone within the tena nt group, but it can be done for only one phone at a time. 1.4.2.1 [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-9 1.4.2.2 Station Related MMC The MMC programs related to the function of the station are as follows: T able 1.3 St ation Related MMC list MMC No. MMC Name MMC: 300 CUSTOMER ON/OFF PER ST A TION MMC: 301 ASSIGN ST A TION COS MMC: 302 PICKUP GROUPS MMC: 303 ASSIGN BOSS/[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-10 Samsung Business Communications 1.4.2.3 Trunk Related MMC The MMC programs related to the function of the trunk are as follows: T able 1.4 T runk Related MMC list MMC No. MMC Name MMC: 400 CUSTOMER ON/OFF PER TRUNK MMC: 401 TRUNK LINE/PBX LINE MMC: 402 TRUNK DIAL TYPE MMC: 403 TRUN[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-11 1.4.2.4 Timer and Tone Related MMC The MMC programs related to the function of the timer and tone are as follows: T able 1.5 Timer and T one Related MMC lis t MMC No. MMC Name MMC: 500 SYSTEM-WIDE COUNTERS MMC: 501 SYSTEM TIMERS MMC: 502 ST A TION-W ID E TIMERS MMC:[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-12 Samsung Business Communications T able 1.6 Group Related MMC list(cont inued) MMC No. MMC Name MMC: 614 ST A TION/TRUNK USE GROUP MMC: 615 MGI GROUP MMC: 616 MGI USER 1.4.2.6 Tables, Codes, AA, DECT and VM MMC The MMC programs related to the function of th e tables, codes, AA, DECT[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-13 T able 1.7 T ables, Codes, AA, DECT and VM MMC list( continued) MMC No. MMC Name MMC: 727 SYSTEM VERSION DISPLA Y MMC: 728 CID TRANSLA TION T ABLE MMC: 740 ST A TION P AIR MMC: 746 COSTING DIAL PLAN MMC: 747 RA TE CALCULA TION T ABLE MMC: 750 VM CARD REST ART MMC: 7[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-14 Samsung Business Communications 1.4.3 Technician Level Programming This level is allowed to program every level of program. This level of programming can be done on every phone within the system, but it can be done for only one phone at a tim e. T able 1.8 T echnician L ev el Progr[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-15 T able 1.8 T echnician Level Programming list(cont inued) MMC No. MMC Name MMC: 837 SIP OPTIONS MMC: 838 PRIV A TE IP ADDRESSES MMC: 839 SIP USER MMC: 840 IP PHONE INFORMA TION MMC: 841 SYSTEM IP OPTIONS MMC: 845 WLAN P ARAMETERS MMC: 846 WIP INFORMA TION MMC: 848 W[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-16 Samsung Business Communications 1.5 Programming List by Name This programming list is arranged alphabetically T able 1.9 Alphabetically arranged Programming list MMC Name MMC No. ACCOUNT CODE MMC: 708 ALARM AND MESSAGE MMC: 1 16 ALARM REMINDER CLOCK MMC: 1 12 ALARM REPORTING MMC: 8[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-17 T able 1.9 Alphabetically arra nged Programming list(continued) MMC Name MMC No. ASSIGN SYSTEM LINK ID MMC: 820 ASSIGN SYSTEM REFERENCE CLOCK MMC: 826 ASSIGN SYSTEM SPEED DIAL MMC: 705 ASSIGN TRUNK GROUP MMC: 603 ASSIGN TRUNK MOH SOURCE MMC: 408 ASSIGN TRUNK SIGNAL [...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-18 Samsung Business Communications T able 1.9 Alphabetically arra nged Programming list(continued) MMC Name MMC No. CONFIRM OUTGOING CALL MMC: 314 CONNECTION ST A T US MMC: 434 COPY COS CONTENTS MMC: 700 COPY KEY PROGRAMMING MMC: 720 COPY ST A TION USABLE MMC: 316 COST RA TE MMC: 433 [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-19 T able 1.9 Alphabetically arra nged Programming list(continued) MMC Name MMC No. HARDW ARE VERSION DISPLA Y MMC: 859 HOLIDA Y ASSIGNMENT MMC: 512 HOT LINE/OFF HOOK SELECTION MMC: 306 HOTEL OPERA TION MMC: 813 HOTEL TIMER MMC: 513 IDLE DISPLA Y MMC: 719 INITIALIZE PO[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-20 Samsung Business Communications T able 1.9 Alphabetically arra nged Programming list(continued) MMC Name MMC No. PICKUP GROUPS MMC: 302 PRESET FOR W ARD NO ANSWER MMC: 320 PRI OPTIONS MMC: 420 PRIV A T E IP ADDRESSES MMC: 838 PROGRAM DOWNLOAD MMC: 818 PROGRAMMED ST A TION MESSAGE M[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-21 T able 1.9 Alphabetically arra nged Programming list(continued) MMC Name MMC No. ST A TION-W ID E TIMERS MMC: 502 SYSTEM ALARM ASSIGNMENTS MMC: 852 SYSTEM KEY PROGRAMMING MMC: 723 SYSTEM SIO MODE MMC: 804 SYSTEM IP OPTIONS MMC: 841 SYSTEM OPTIONS MMC: 861 SYSTEM RES[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-22 Samsung Business Communications T able 1.9 Alphabetically arra nged Programming list(continued) MMC Name MMC No. VIRTUAL EXTENSION TYPE MMC: 822 VM ALARM MMC: 755 VM CARD REST ART MMC: 750 VM DA Y/NIGHT MMC: 758 VM HAL T MMC: 754 VM IN/OUT MMC: 757 V oIP ACCESS CODE MMC: 832 V oIP [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-23 1.6 Program List by Function This section describes MMC programs are classified by the function of the OfficeServ 7100. 1.6.1 Phone Function The MMC programs related to the function of a phone that is connected with the Of fice- Serv 7100 are as follows: T able 1.10[...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-24 Samsung Business Communications 1.6.2 Networking Function The MMC programs related to the function of networking are as follows: T able 1.1 1 Networking Function Programming list MMC Program No. Program Description MMC: 820 ASSIGN SYSTEM LINK ID MMC: 821 ASSIGN NETWORK TRUNK MMC: 8[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-25 T able 1.12 V oIP Function Programming list(continued ) MMC Program No. Program Description MMC: 835 MGI DSP OPTIONS MMC: 836 H.323 GK OPTIONS 1.6.4 WLAN Function The MMC programs related to the function of WLAN(W ireless Lo cal Area Network) are as follows: T able [...]

CHAPTER 1. Ошибка ! Стиль не определен . 1-26 Samsung Business Communications 1.6.6 Auto Attendant/Voice Mail Function The MMC programs related to the function of AA(Auto Attendant) or VM(V oice Mail) are as follows: T able 1.15 Auto A ttendant/V oice Mail Function Programming list MMC Program No. Program Description MMC: 207 [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 1-27 1.6.7 Diagnosis Function The MMC programs related to the function of diagnosing the s ystem are as follows: T able 1.16 Diagnosis Function Progra mming list MMC Program No. Program Description MMC: 434 CONNECTION ST A T US MMC: 851 ALARM REPORTING MMC: 852 SYSTEM AL[...]

[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-1 CHAPTER 2. MMC Programming This chapter describes how to use each MMC program as it was listed. 2.1 Overview of Programming Procedure The order of programming will be discussed before explaining programming method of each list. Please read the description carefully b[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-2 Samsung Business Communications 2.2 Programming Procedure This section describes a procedure of each program. Refer to the programming procedure corresponding to the MMC. [100] STATION LOCK Allows the system administrator or technician to lock or unlock an individual station or all [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-3 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 100. Display shows: [201] STN LOCK UNLOCKED 2) Dial station number .(e.g., 205) OR [205] STN LOCK U NLOCKED Press V olume button to select station and press Right Soft button to move cursor . OR Select all[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-4 Samsung Business Communications [101] CHANGE USER PASSCODE Allows the system administrator or technician to reset any phone’ s passcode to its default value of ‘1234’. This MMC cannot display sta tion passcodes; it can only reset them to de- fault. Phone users can set or chang[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-5 [102] CALL FORWARD Allows the system administrator to program the call forward destinations for other station users. This MMC also allows call forward to be set after the destination has been entered. Allows several types of call forwarding: FOR W ARD ALL, FOR W ARD [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-6 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 102. Display shows: [201] FORWARD 0:FORWARD CANCEL 2) Dial station number .(e.g., 205) OR [205] FORWARD 0:FORWARD CANCEL Press V olume button to select station and press Ri g ht Soft button[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-7 [103] SET ANSWER MODE Allows the system administrator to change the answer mode of any phone. Each phone can have its answer mode set to one of the following opti ons: No Ty p e Description 0 RING MODE The phone will ring in one of eight custom rin g p atterns. Calls[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-8 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 103. Display shows: [201] ANS MODE RING MODE 2) Dial phone number .(e.g., 205) OR [205] ANS MODE RING MODE Press V olume button to select phone and press Right Soft button to move cursor .[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-9 [104] STATION NAME Allows the system administrator or technician to enter a name up to 1 1 characters to iden- tify an individual station. ENTERING CHARACTERS Names are written using the keypad. Each key press selects a ch aracter . Pressing the dial pad key moves th[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-10 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 104. Display shows: [201] STN NAME 2) Dial station number .(e.g., 205) OR [205] STN NAME _ Press V olume button to select station and press Right Soft button to move cursor . 3) Enter the [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-11 [105] STATION SPEED DIAL Allows the system administrator or technici an to assign phone numbers to a station’ s per- sonal speed dial locations. CONDITIONS Each station may have up to 50 locations(or bins) assigned to it in MMC 606(Assign Speed Block). The speed d[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-12 Samsung Business Communications 4) Enter trunk access code(e.g., 9) followed by the number to be dialed.(e.g., 4264100) [205] SPEED DIAL 05:9-4264100_ OR Press Right Soft button to return to step 2. OR Press Left Soft button to return to step 3. Press Hold button to clear an entry [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-13 [106] STATION SPEED DIAL NAME Allows a name up to 1 1 characters to be ente red for each personal speed dial location. This allows speed dial numbers to be selected by na me when the directory dial feature is used. ENTERING CHARACTERS Refer to ‘ENTERING CHARACTERS[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-14 Samsung Business Communications [107] KEY EXTENDER Use this program to view the programmable buttons assigned to stations. In addit ion, it al- lows the system administrator to assign key extenders to some keys to make a general ac- cess feature key more specific. The feature keys [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-15 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 107. Display shows first station: [201] EXT (MAST) 01:CALL1 Æ 2) Dial station number .(e.g., 205) OR [205] EXT (MAST) 01:CALL1 Æ Use V olume button to scroll through station numbers and press Right Soft[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-16 Samsung Business Communications [108] STATION STATUS This is a READ-ONL Y MMC. Displays the following attributes of a station port. No Statu s Description 0 PORT NO Cabinet(1)/Sl ot(MP ,1,2)/Port(1-12) 1 TYPE Phone T ype 2 PICKUP GROUP None, 01-99 3 SGR S tation Group Number 4 BOSS[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-17 RELATED ITEMS MMC 301 ASSIGN ST A TION COS MMC 302 PICKUP GROUPS MMC 303 ASSIGN BOSS/SECRET AR Y MMC 601 ASSIGN ST A TION GROUP MMC 604 ASSIGN ST A TION T O P AGE ZONE[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-18 Samsung Business Communications [109] DATE DISPLAY Allows the system administrator or technician to select the date and time display mode on a per-station basis or system-wide. No Mode Description 0 COUNTRY Sets overall display format and has t w o options: 0 = ORIENT AL MM/DD DA Y[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-19 5) Press T ransfer button to save and exit. OR Press Speaker button to save and advance to next MMC. RELATED ITEMS MMC 505 ASSIGN DA TE AND TIME[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-20 Samsung Business Communications [110] STATION ON/OFF Allows the system administrator to set any of the phone features listed below . No Feature Default Description 00 AUTO HOLD OFF Automatica lly places an existing T runk Line call on hold if a CALL key , trunk key or trunk route k[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-21 (continued) No Feature Default Description 14 NOT CONT .CID ON When OFF , the Caller ID will be displa yed for the dura- tion of the call. When ON, displays timer for duration of call(if AUT O TIMER also set on). 15 AUTO ANS CO OFF W hen ON, keyset will automaticall[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-22 Samsung Business Communications RELATED ITEMS MMC 301 ASSIGN ST A TION COS MMC 701 ASSIGN COS CONTENTS[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-23 [111] PHONE RING TONE Allows the system administrator or technician to select the ring tone heard at each phone. Eight ring tones are available. A short tone burst of the selection will be heard when the dial keypad is pressed. DEFAULT DATA FREQUENCY : 5 A C T I O N[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-24 Samsung Business Communications [112] ALARM REMINDER CLOCK Allows the system administrator or technician to set or change the alarm clock/appointment reminder feature for any station. Three alarms may be set for each station and each alarm may be defined as a one-time or T ODA Y al[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-25 RELATED ITEMS MMC 1 16 ALARM AND MESSAGE[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-26 Samsung Business Communications [113] VIEW MEMO NUMBER Allows a station user the ability to view a memo left by the user . A memo can be left by en- tering it via the dial keypad using the table below . A memo of up to and including 13 char- acters can be entered. ENTER CHARACTERS [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-27 [114] PHONE VOLUME Allows the station user or system administrator to set the ring volume, off-hook ring vol- ume, handset receive volume, speaker volume, background music volume and page volum e for any or all phones. No Ty p e Description 0 RING VOLUME This is the[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-28 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 1 14. Display shows: [201] STN VOLUME RING VOLUME :4 2) Dial phone number .(e.g., 205) [205] STN VOLUME R ING VOLUME :4 3) Dial volume type.(e.g., 3) OR [205] STN VOLUME SPEAKER VOL :13 Pr[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-29 [115] SET PROGRAMMED MESSAGE Allows the system administrator to set a programmed message at any or all display phones. There are 20 messages(01-20) available. The last five message can be modified by each phone user . CONDITIONS These messages are as set up in MMC 7[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-30 Samsung Business Communications [116] ALARM AND MESSAGE Allows the system administrator or technician to set or change the alarm clock/appointment reminder feature for any station. Three alarms may be set for each station and each alarm may be defined as a one-time or T ODA Y alarm[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-31 5) Dial valid entry from above list for alarm type. (e.g., 2) [205] ALM REM HHMM:1300 Æ DAILY OR Press V olume button to select alarm type and press Right Soft button to move cursor . 6) Enter message and press R ight Soft button to return to step 2. [205] ALM REM [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-32 Samsung Business Communications [117] EDIT TEXT MESSAGE Allows the system administrator or technician to set or change text messages for any sta- tion. One station can use up to 10 text messages. CONDITIONS Only stations allowed to use text messages in MMC 61 1 can be selected here[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-33 [118] CONFERENCE GROUP Allows the system administrator or technician to set conference groups for any station. A station is allowed up to five conference groups, and each group can include 4 members (excluding the station itself). Names can be allocated to groups. C[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-34 Samsung Business Communications 5) Enter conference member dial number and press Right Soft button to return to step 4. [205] GRP(1)MBR1 9-2794296 6) Press T ransfer button to save and exit. OR Press Speaker button to save and advance to next MMC. RELATED ITEMS MMC 612 ALLOW GROUP [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-35 [119] CALLER ID DISPLAY Allows the technician to set the individual st ation display preference on a per-station basis. Caller ID or CLI can be selected to either s how the name, number first, or no display de- pending on the type of call. Caller ID or CLI displays [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-36 Samsung Business Communications [120] LARGE LCD OPTIONS Allows the system administrator to set any of the following options for lar ge LCD phones. No Option Description 0 IDLE DISPLA Y Sets whether to display ‘ CALENDAR ’ or ‘ INFORMA TION ’ on LCD when idle. 1 DS KEY DISPL[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-37 4) Press V olume button to select display type and pre ss Ri g ht Soft button. [203] DS KEY DSP EXT NAME 5) Press T ransfer button to save and exit. OR Press Speaker button to save and advance to next MMC. RELATED ITEMS MMC 719 IDLE DISPLA Y[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-38 Samsung Business Communications [121] PHONE LANGUAGE Allows the system administrator to assign an LCD display based on the user ’ s ow n lan- guage. No Language 00 ENGLISH 01 GERMAN 02 PORTUGAL 03 NORSK 04 DANISH 05 DUTCH 06 IT AL Y 07 SP ANISH 08 SWEDISH 09 SP ANISH/USA 10 FRENC[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-39 RELATED ITEMS NONE[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-40 Samsung Business Communications [122] NEWS DISPLAY SPEED Used to set the Smart News display speed between 0300 mS(fastest) and 1 sec(slowest). This timer is related to the Smart News PC Application Package. DEFAULT DATA 03(0300 mS) A C T I O N D I S P L A Y 1) Press T ransfer butto[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-41 [125] EXECUTIVE STATE Allows the system administrator or technician to set an executive station’ s options, as fol- lows. No Option Description 0 EX EC ST A T E When working with EASYSET , t he state of the executive station can be displayed.(e.g., IN A MEETING) 1[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-42 Samsung Business Communications RELATED ITEMS NONE[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-43 [199] SHOW LICENSE STATUS Allows the system administrator or technician to confirm the status(V alid or Invalid) of the inserted license key . No F eature Description 0 MGI MAX The license status for MGI port 1 VMS MAX The license status for VMS port 2 SOFT MAX The [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-44 Samsung Business Communications [200] OPEN CUSTOMER PROGRAMMING Used to open(enable) and close(disable) cu stomer-level programming. If pr ogramming is not opened and an attempt is made to access a system MMC, the error message [NOT PERMIT] will be displayed. A four digits passcode[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-45 [201] CHANGE CUSTOMER PASSCODE Used to change the passcode allowing access to MMC 200, Open Customer Programming, from its current value. CONDITIONS y The passcode is four digits long. Each digit can be 0-9. y The current(old) passcode is required for this MMC. DEFA[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-46 Samsung Business Communications [202] CHANGE FEATURE PASSCODE Used to change the passcodes for the following features. No F eature Description 0 RING PLAN The passcode required to place the system in different Ring Plans(RP) or change the Ring T ime Override(RTO). 1 DISA ALARM T he[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-47 4) Press T ransfer button to save and exit. OR Press Speaker button to save and advance to next MMC. RELATED ITEMS MMC 410 ASSIGN DISA TRUNK MMC 507 ASSIGN RING PLAN TIME[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-48 Samsung Business Communications [203] ASSIGN UA DEVICE Assigns ringing device to be accessed when a Un iversal Answ er(UA) key is pressed or the UA pickup code is dialled. UA assign ment is made in MMC 601, Assign Station Group, for a group and then the group is entered here. The d[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-49 [204] COMMON BELL CONTROL Determines whether the common bell relay contact s have an interrupted or continuous clo- sure when activated. If interrupted is chosen, the relay follows an internal T runk Line ring pattern of one second closed followed by three seconds o[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-50 Samsung Business Communications [205] ASSIGN LOUD BELL Designates the station that controls the loud bell ring output of a MIS card.(Each MIS card provides one loud bell port.) The loud bell w ill follow the ring cadence of the designated station. CONDITIONS Only a station can be a[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-51 [206] BARGE-IN TYPE Sets the type of barge-in that is permitted. No Ty p e Description 0 NO BARGE-IN Barge-i n feature is unavail able regardless of a st ation’s barge-in status. 1 WITH TONE Barge-i n will have an in trusion tone and display at the station barged-[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-52 Samsung Business Communications [207] ASSIGN VM/AA PORT Enables SLI ports to be designated as NORMAL or VM/AA. VM/AA ports receive digits and also receive a true disconnect signal on completion of a call. Only SLI cards, not key- set daughter-boards, support disconnect signal. Do n[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-53 [208] ASSIGN RING TYPE Allows programming of single lines to have ICM ringing, T runk Line ringing and data se- cure. W ith the many ty pes of external ringing devices, all configurations can be met. All devices will also have a positive disconnect si gnal. Do not m[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-54 Samsung Business Communications [209] ASSIGN ADD-ON MODULE Designates to which phone an add-on module( AOM) is assigned. There is no limit to the number of AOMs that can be assigned in the system. A maximum of four AOMs can be as- signed to a keyset. CONDITIONS An AOM cannot be des[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-55 [210] CUSTOMER ON/OFF PER TENANT Allows the system administrator to set system features on a per-tenant basis. Each system option has a corresponding dialling number , as listed below . All options toggle ON/OFF . No Option Default Description 00 DISA PSWD ON W hen [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-56 Samsung Business Communications (continued) No Option Default De scription 1 4 I C M E X T FW D O F F When ON, call for ward external is allowed when intercom calls are placed to a station that has Call For w ard External pro- grammed and set. 16 DID ERR TONE OFF This option pro vi[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-57 (continued) No Option Default Description 39 SGR ALL OUT OFF When ON, the last remaining station group member can leave a group. 40 CHAIN FWD ON If ON, an incoming call for w arded from a station to another station may then be forwarded to the mailbox of the second [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-58 Samsung Business Communications (continued) No Option Default Description 56 VOIP REALRBT OFF When ON, the system wi ll connect the real path of the outgo- ing trunk to the incoming V oIP trunk user instead of providing virtual ringback tone. 57 CO-CO TM ALL OFF When ON, the system[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-59 DEFAULT DATA SEE DESCRIPTION SOME OPTIONS DEPEND ON COUNTR Y A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 210. Display shows: TEN. ON AND OFF D ISA PSWD :OFF 2) Dial option number .(e.g., 00) Press Right Soft button to move cursor . TEN. ON AND OFF[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-60 Samsung Business Communications [211] DOOR RING ASSIGNMENT Designates which station or group of stations will ring when a door phone button is pressed. If the ring plan destinations are not entered the default ring plan 1 is used. A vailable ring plans are 1 to 6. DEFAULT DATA ST A[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-61 [214] DISA ALARM RINGING STATION Assigns the DISA alarm to ring at a specific phone. It is recommended that the person who can clear the alarm also receives the notification. CONDITIONS y A valid destination can be either a station group or an individual station. y [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-62 Samsung Business Communications [217] TRAFFIC REPORT OPTION This MMC is used to print a traf fic report and select options. The traf fic report can be printed on demand, or every hour , or at a programmed time each day , or for up to three separately-timed shifts. Automatic printin[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-63 A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 217. Display shows: TRAFFIC REPORT M ANUAL PRINTOUT 2) Dial 0 for manual or 1 for automatic print. OR TRAFFIC REPORT A UTO PRINT OPTN Press V olume button to select and press Right Soft button. 3) If AUT[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-64 Samsung Business Communications [219] RELAY TYPE Assigns the service type of three relay ports of misc card. Service consists of External Page, Common bell , loud bell, NOT USED. DEFAULT DATA External Page A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 219. Display [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-65 [220] ISDN SERVICE TYPE Assigns the ISDN service type of a single line telephone port. Service consists of BC (Bearer Capability) and HLC(High Layer Capability). No Ty p e Description BC HLC 0 VOICE V oice service S peech - 1 F AX 3 G3 F AX service 3.1 kHz Audio FAX[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-66 Samsung Business Communications [221] EXTENSION TYPE This MMC assigns station ports for a specific use. Each phone can be designated as one of five types(see table). These types can be cha nged by dialling the type number or by scroll- ing through the types and pressing the Right S[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-67 3) Dial 0 - 5 to select station type. OR [214] PHONE USE G UEST NO SMOKING Press V olume button to select option and press Right Soft button. 4) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. RELATED ITEMS MMC 813 HOTEL OPER[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-68 Samsung Business Communications [222] FAX PAIR Enables a guest room to have a normal phone line and fax line simultaneously . Only a Guest No Smoking Room or Guest Smoking Room can be assigned a fax pair station which is already assigned as a fax station in MMC 221. DEFAULT DATA NO[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-69 [224] WAKE-UP ANNOUNCEMENT This MMC is an enhanced W ake Up feature. The s ystem will play a recorded message when a W ake Up call is answered by the user . The W ake Up Announcem ent feature re- quires an SVMi-20 card to be installed in the system. When a W ake Up [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-70 Samsung Business Communications 3) Enter the AA group num ber . OR WAKE-UP ANNOUNCE AA GROUP :5 20 Press V olume button to select and press Right Soft button to return to step 2. 4) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. RELATED ITE[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-71 [300] CUSTOMER ON/OFF PER STATION Allows the following features to be enab led/disabled on a per-station basis. No Optio n Default Description 00 ACCESS DIAL ON Determines whether a user can select a trunk or trunk group by dialling its Directory Number(DN). This se[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-72 Samsung Business Communications DEFAULT DATA SEE DESCRIPTION SOME OPTIONS DEPEND ON COUNTR Y A C T I O N D I S P L A Y 1) Press T ransfer button and enter 300. Display shows: [201] CUS.ON/OFF ACCESS DIAL :ON 2) Dial station number .(e.g., 205) OR [205] CUS.ON/OFF A CCESS DIAL :ON P[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-73 [301] ASSIGN STATION COS Used to assign a class of service to each phone. There are 30 dif ferent classes of service (defined in MMC 701, Assign COS Contents) and six ring plans based on the Ring Plan T ime in MMC 507 that can apply to the COS. Classes of service ar[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-74 Samsung Business Communications 5) Enter the next ring plan class of service.( e.g., 05) OR [205] STN COS 1:05 2:01 3:01 Use V olume button to scroll through classes of service and press Right Soft button to move cursor to the next ring plan. OR Use V olu me button to scroll throug[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-75 [302] PICKUP GROUPS Allows the assignment of stations into call pickup groups. There is a maxim um of 20 pickup groups. An unlimited number of member s can belong to each group. S tations can only be in one pickup gr oup at any given time. DEFAULT DATA NO PICKUP GRO[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-76 Samsung Business Communications [303] ASSIGN BOSS/SECRETARY Assigns BOSS phones to SECRET AR Y phones. One BOSS station can have up t o and in- cluding four SECRET AR Y stations and one SECRET AR Y station can have up to and in- cluding four BOSS stations. CONDITIONS y A dedicated [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-77 [304] ASSIGN EXTENSION/TRUNK USE Allows you to select which stations are a llowed to make calls through C.O. lines or to answer calls for C.O. lines.(on a station and trunk use group basis) CONDITIONS y Stations are set within use group numbers 001~100and trunks are[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-78 Samsung Business Communications 4) Press V olume button to select YES/NO option. OR (005) USE (101) DIAL:NO ANS:Y ES Dial 1 for YES or 0 for NO and press Right Soft button to m ove cursor to ANS option. Press V olume button to select YES/NO Option. OR (005) USE (101) DIAL:NO ANS:YE[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-79 [305] ASSIGN FORCED CODE This MMC allows one of the four options to be selected: the assignment of account codes with verification, account codes without verifi cation and authorization codes(or n one of these) on a per- station basis or on an all-station basis. The[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-80 Samsung Business Communications [306] HOT LINE/OFF HOOK SELECTION Allows a station to make a predetermined call, similar to a ring-down circuit, upon the ex- piration of a timer .(see MMC 502, ST A TION TIMERS, Of f-Hook Selection T imer) CONDITIONS y The hotline destination can be[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-81 [308] ASSIGN BACKGROUND MUSIC SOURCE Assigns a background music source to phones. Th ere is one internal music source/external music source. The default directory numbers for the music sources are 371. CONDITIONS T o use an external sound source, connect th e corres[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-82 Samsung Business Communications [309] ASSIGN STATION MOH SOURCE Assigns a Music On Hold source to phones. Th ere is one internal music source/external music source. The default directory numbers for the music sources is 371. CONDITIONS T o use an external sound source, connect th e[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-83 [310] LCR CLASS OF SERVICE Assigns the LCR class of service allowed on a per-station/per -trunk basis. There are eight classes which may be assigned. LCR class of service allows specifi c users to ‘trunk ad- vance’ up to a matching LCR class of service programme[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-84 Samsung Business Communications [312] ALLOW CALLER ID Allows the system administrator or technician to allow or deny CID data to be sent from, or displayed at, LCD phones. Option Description RCV Set whether to display CID. SND Set w hether to send CID for ISDN calls. DEFAULT DATA R[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-85 [314] CONFIRM OUTGOING CALL Allows outgoing call restriction by call duration tim e: calls can be disconnected or the user can receive ‘confirm tone’.(refer to the CO Confirm timer in MMC 501) No Ty p e Description 0 NONE No action 1 CONFIRM TO NE Caller hears c[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-86 Samsung Business Communications [315] CUSTOMER SET RELOCATION Customer Set Relocation allows the system admi nistrator or technician to exchange similar stations in the system without hardware chang es. All the button settings, features, etc. for a phone can be copied to another . [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-87 Relocate All ow ed Ta b l e SL T EURO 6B EURO 12B EURO 24B 48B AOM 64B AOM i DCS 28D i DCS 18D SL T YES NO NO NO NO NO NO NO EURO 6B NO YES NO NO NO NO NO NO EURO 12B NO NO YES YES NO NO NO NO EURO 24B NO NO YES YES NO NO NO NO 48B AOM NO NO NO NO YES YES NO NO 64B [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-88 Samsung Business Communications Relocate All ow ed Ta b l e i DCS 8D DS- 5012L DS- 5014D DS- 5021D DS- 5007S DS- 5014S DS- 5038S IP Phone* SL T NO NO NO NO NO NO NO NO EURO 6B NO NO NO NO NO NO NO NO EURO 12B NO NO NO NO NO NO NO NO EURO 24B NO NO NO NO NO NO NO NO 48B AOM NO NO NO[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-89 [316] COPY STATION USABLE Provides a tool for copying station/trunk use assignments in MMC 304 from one station user group to another . This can be done o n a station use group basis or for all station use groups. Use groups are set up in MMC 614. DEFAULT DATA NONE [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-90 Samsung Business Communications [317] ASSIGN STATION/STATION USE This MMC is used to determine whether stati ons in one use group can make intercom calls to stations in other use groups.(within the same tenant) Use groups are set up in MMC 614. DEFAULT DATA DIAL: YES A C T I O N D [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-91 [318] DISTINCTIVE RINGING Allows the technician to select the ring tone h eard at a keyset when called by a specific sta- tion or when a specific trunk rings that keyset. There is also a cadence control option to perform a similar function for SL T s. There are eigh[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-92 Samsung Business Communications DEFAULT DATA T : NO (FOLLOW ST A TION SET TING) C: NO (FOLLOW ST A TION SETTING) A C T I O N D I S P L A Y 1) Press T ransfer button and enter 318. Display shows first station: [201] RING TONE T:NO C:NO PRI:NO 2) Dial trunk or station number .(e.g., [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-93 [319] BRANCH GROUP Assign stations to branch groups. There is a maximum of four branch groups. When a C.O. line is ringing at a station, other stations assigned the same branch group can answer the in- coming call by going of f hook. MMC [319] This MMC is currently [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-94 Samsung Business Communications [320] PRESET FORWARD NO ANSWER Allows a technician to assign a default des tination for Forward No Answer(FNA) to each station on the system. These destinations may be the same or different for each station. The preset FNA destination will be tempora[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-95 4) Dial call type 0, 1 or 2.(e.g., 1) OR [205] PRESET FNA 202 OPT:EXT Press V olume button to make selection and press Right Soft button to return to step 2. 5) Press T ransfer button to save and exit. OR Press Speaker button to save and advance to next MMC. RELATED[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-96 Samsung Business Communications [323] CALLING PARTY NUMBER Allows a number up to 16 digits to be entered and associated with a station or trunk num- ber on a per PRI/BRI basis. When this station makes an outgoing call on this PRI, the number entered here will be the Calling Party N[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-97 [326] RINGBACK TONE MESSAGE Assigns Color Ring Message by using SVMi message. DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button and enter 326. Display shows: [301] RBT MSG NONE 2) Enter the VM station number . OR [302] RBT MSG NONE Press V olume [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-98 Samsung Business Communications [400] CUSTOMER ON/OFF PER TRUNK Assigns several options(listed below) on a per -trunk basis. No Option Default Description 0 1A2 EMULA TION OF F When this opti on is set to ON up to 4 internal stations can participate in a conversation on this trunk [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-99 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 400. Display show: [701] TRK ON/OFF 1A2 EMULATE:OFF 2) Dial trunk number .(e.g., 704) OR [704] TRK ON/OFF 1A2 EMULATE:OFF Press V olume button to select trunk. OR Select all trunks and press Right Soft bu[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-100 Samsung Business Communications [401] TRUNK LINE/PBX LINE Used to select the mode of the trunk lines: CO LINE or PBX LINE. If PBX m ode is chosen, this allows PBX access codes to be recognized, thus allowing more complete toll restriction. (call barring) This m ode is assigned on [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-101 [402] TRUNK DIAL TYPE Used to determine the dialling type of each trunk line. There are two options: No Ty p e Description 0 DTMF TYPE Dual T one Multi-Frequency 1 DIAL PULSE TYPE Dial Pulse DEFAULT DATA ALL TRUNKS: DTMF A C T I O N D I S P L A Y 1) Press T ransfer[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-102 Samsung Business Communications [403] TRUNK TOLL CLASS Assigns to ll class level assignments on a per-tr unk or all-trunk basis in a day or night con- dition. The options for toll level will follow either the station class or the class of service defined in MMCs 702, T oll Deny T [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-103 4) Enter day toll class.(e.g., 2 for CLS-B) OR [704] TOLL CLASS 1:CLS-B 2:F-STN Press V olume button to scroll through toll classes and use Right Soft button to move the cursor . 5) Press T ransfer button to save and exit. OR Press Speaker button to advance to next[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-104 Samsung Business Communications [404] TRUNK NAME Allows a name up to 1 1 characters long to be entered to identify an individual trunk. ENTERING CHARACTERS Refer to ‘ENTERING CHARACTERS’ in MMC 104, ST A TION N AME. DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfe[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-105 [405] TRUNK CO TEL NUMBER Allows a number up to 1 1 digits long to be entered to identify an individual trunk. ENTERING NUMBERS Numbers are written using the keypad. Each press of a key selects the digit and moves the cursor to the next position. The # button can b[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-106 Samsung Business Communications [406] TRUNK RING ASSIGNMENT Enables ringing to a specific station or to a group of stations when incoming calls are re- ceived. This MMC controls ring plan destinations for ring down trunks. If the ring plan destinations are not entered, the default[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-107 [407] FORCED TRUNK RELEASE Provides a positive forced trunk release to a specific trunk or all trunks in the event of a trunk lock-up. DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 407. Display shows: [701] TRK RELS. RELEASE?_Y:1,[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-108 Samsung Business Communications [408] ASSIGN TR UNK MOH SOURCE Allows the system administrator to select which Music-On-Hold(MOH) source can be heard on each trunk. There is one internal m usic source/external music source (371). CONDITIONS T o use an external sound source, connec[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-109 [409] TRUNK STATUS READ This is a READ-ONL Y MMC. Allows the status of trunks to be read in a format that will enable the servicing personnel to quickly id entif y the ownership and position of a trunk. No Ty p e Description 00 PORT Port Number(Cabin et/Slot/Port) [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-110 Samsung Business Communications RELATED ITEMS MMC 400 CUSTOMER ON/OFF PER TRUNK MMC 401 TRUNK LINE/PBX LINE MMC 402 TRUNK DIAL TYPE MMC 403 TRUNK T OLL CLASS MMC 404 TRUNK NAME MMC 406 TRUNK RING ASSIGNMENT MMC 408 ASSIGN TRUNK MUSIC ON HOLD SOURCE MMC 410 ASSIGN DISA TRUNK[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-111 [410] ASSIGN DISA TRUNK Allows the system to have Direct Inward System Access(DISA). Because there is a possi- bility that unauthorized calls will be made via this feature, several safeguards have been added. Users must be informed of these to prevent unnecessary s[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-112 Samsung Business Communications [412] ASSIGN TRUNK SIGNAL Allows the assignment of analogue DID or E & M cards for proper signalling. Th ese trunks can also use the translation tables in MMC 714. No Signalling c ondition type 0 IMMEDIA TE ST AR T 1 DELA YED ST AR T 2 WINK ST A[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-113 [414] MPD/PRS SIGNAL Used on a per-trunk basis t o define if a T runk line is to be either a Metering Pulse Detec- tion(MPD) or a Polarity Reversal Signal(PRS) trunk. An MPD T runk will detect a C.O-provided mete r pulse. A Polarity Reversal trunk will de- tect the[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-114 Samsung Business Communications 3) Dial 0 for PRS 1, 1 for PRS 2, 2 for PRS 3, 3 for MPD or 4 for NORMAL. [705] TRK PRS PRS 2 OR Press V olu me button to scroll through options and use Left or Right Soft button to return to step 2. 4) Press T ransfer button to save and exit. OR Pr[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-115 [415] REPORT TRUN K ABANDON DATA Allows the system administrator or technician to enable or disable the reporting of aban- doned T runk Line calls for which CLIP information has been collected on a per -trunk basis. There are two options for this MMC: No Option De [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-116 Samsung Business Communications [417] E1/PRI CRC4 OPTION This option is used to enable/disable CRC4 generation and checking. CONDITIONS y This is useful with some networks which do not support CRC4 framing but only PCM30 framing. y After changing this option, MMC 418 must be used [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-117 [418] BRI AND PRI CARD RESTART This MMC is used to restart a BRI or PRI card at the card level. This action is required to update the processor on the BRI or PRI card w ith any changes in the card setup MMCs and to put these changes into effect. CONDITIONS y A BRI [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-118 Samsung Business Communications [419] BRI OPTIONS Assigns several options on a per -BRI basis. There are dif ferent options depending on whether the BRI is programmed as a trunk or station in MMC 423. OPTIONS FOR BRI PORTS PROGRAMMED AS TRUNKS No Option Description 0 CHANNEL ANY W[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-119 (continued) No Option Description NB P LAN Used to select the type of the Calling Party Number Plan to send to the net- wor k. UNKNOWN Unknown numbering pl an ISDN ISDN numbering plan(CCIT T E.163-164) DA T A Data numbering plan(CCITT X.121) TELEX T elex n umbering[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-120 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 419. Display shows first BRI channel. [725] BRI-TRK CHANNEL ANY:YES 2) Dial BRI trunk number .(e.g., 727) OR [727] BRI-TRK CHANNEL ANY:YES Press V olume button to select BRI trunk and pre[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-121 RELATED ITEMS MMC 323 CALLING P AR TY NUMBER MMC 405 TRUNK CO TEL NUMBER MMC 418 BRI & PRI CARD REST AR T MMC 421 MSN DIGIT MMC 423 S/T MODE MMC 714 DID NAME AND NUMBER TRANSLA TION[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-122 Samsung Business Communications [420] PRI OPTIONS This MMC allows the technician to program a PRI trunk card. No Option Description 0 CHANNEL ANY When this option is set to YES, the system will place calls on any free channel of that PRI if the channel chosen by the user is busy .[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-123 CONDITIONS y Before setting the PRI program, the J2 jumper of the TEPRI or TEPRI2 card must be set to ‘ON’ for PRI mode. y After changing this program, run MMC 418, BRI AND PRI CARD REST AR T , to ap- ply the new setting. DEFAULT DATA CHANNEL ANY : YES PRI MODE[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-124 Samsung Business Communications [421] MSN DIGIT Provides a method of assigning an incoming MSN call to a specific station. If any entry in the MSN DIGIT T ABLE matches an incoming call’ s called party number , either the spe- cific station is alerted, if it is programmed to acce[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-125 5) Enter destinations for the six ring plans via the dial keypad.(e.g., 204 for ring plan 1) [704] MSN DGT (4) 1:204 2:NONE OR Press V olu me button to make selection and press Right Soft button. 6) Enter 1 for YES or 0 for NO. OR [704] MSN DGT (4) CW:NO OPT:ACEPT [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-126 Samsung Business Communications 2) Dial trunk number .(e.g., 705) OR [705] TRK COS 1:01 2:01 3:01 Use V olu me button to scroll through trunks. Press Right Soft button to advance to step 3. OR Use V olu me button to scroll through trunks and press Left Soft button to advance to st[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-127 [423] S/T MODE Allows the technician to select whether a BRI circuit is a station port or a trunk port. No Ty p e Description 0 TRUNK T he BRI trunk port used for ISDN trunk. 1 ST A TION The BRI trunk port used for ISDN phone. CONDITIONS The BRI card must be instal[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-128 Samsung Business Communications [424] BRI S0 MAPPING This MMC assigns an ISDN terminal number to a BRI station port. CONDITIONS This function can be used only when the BRI card or BRM is installed in the system. DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-129 [425] CID TRUNKS This MMC assigns a TRUNK number to a CID TRUNK. CONDITIONS This function can be used only when the TRM or trunk card is installed in the s ystem. DEFAULT DATA NORMAL TRUNK A C T I O N D I S P L A Y 1) Press T ransfer button and enter 425. Display s[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-130 Samsung Business Communications [426] TRUNK GAIN CONTROL Allows loss levels to be adjusted on a per -tr unk basis. There are two adjustments available in this MMC: ‘TX’ is the transmission level adju stment of the trunk to the station. ‘RX’ is the receiving level adjustmen[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-131 [428] ASSIGN TRUNK/TRUNK USE This MMC is used to allow or restrict tr unks from making outgoi ng calls to other trunks within the same system. By default(DIAL=YES) all trunks can use other trunks. T o prevent use, select NO. DEFAULT DATA DIAL: YES A C T I O N D I S[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-132 Samsung Business Communications [432] SET H-TRK This MMC is used to select the type of si gnalling for each H- trunk. There are three opera- tion types available.(E & M, DID, R/D) DEFAULT DATA E & M A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 432. Displa[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-133 [433] COST RATE In this MMC, the TRUNK COST RA TE flags ar e entered for each trunk. DIAL PLANs are defined in MMC 746(Costing Dial Plan). RA TE CALCULA TION T ABLES are defined in MMC 749. Each trunk may be defined with up to ei ght cost rates. Enter one or more o[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-134 Samsung Business Communications [434] CONNECTION STATUS This read-only MMC will confirm the connecti on status of stations or trunks. Dis play status displays the status of a station or trunk at the time requested. If a conference is in progress with the selected trunk or station,[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-135 Display trunk status in conference 1) Press T ransfer button and enter 434. DISPLAY STATUS 2 01 IDLE 2) Enter station or trunk number . Display shows connection status: DISPLAY STATUS 7 02 227 ,215 Æ 3) Press Right Soft button to display the next station or trunks[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-136 Samsung Business Communications Display connection status with invalid trunk or station number 1) Press T ransfer button and enter 434. DISPLAY STATUS 2 01 IDLE 2) Enter invalid station or trunk number Display show INV ALID DA T A: DISPLAY STATUS INVALID DATA 3) Enter another stat[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-137 [436] TRUNK TMC GAIN Allows loss levels of TMC for analogue trunks to be adjusted on a per -trunk basis. There are two adjustments available in this MMC: ‘T X’ is the transmission level adjustment of the trunk to the station. ‘RX’ is the recei ving level ad[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-138 Samsung Business Communications [437] 16TRK GAIN CONTROL Allows gain levels to be adjusted on a per - trunk basis. There are two adjustments available in this MMC: ‘TX’ is the transmission level adju stment of the trunk to the station. ‘RX’ is the receiving level adjustmen[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-139 [500] SYSTEM-WIDE COUNTERS Used to set the values of the system counters. The counters are listed below with a brief de- scription of each. No Counter Default Description 0 ALARM REM. CNTER 5 The number of times that an alarm reminder will ring a station before can[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-140 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 500. Display shows: ALARM REM.CNTER 05 Æ 2) Enter number from above list.(e.g., 6) OR UCDS AUDIO ALARM 00 Æ Press V olume button to make selection and press Right Soft button to move c[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-141 [501] SYSTEM TIMERS Allows the technician to adjust individual timers as necessary . TIMER TABLE Timer Name Default Range Unit Description ALARM TIME 100 0-2500 MIN This is the time the system alarm key will start ringing after the alarm key has been silenc ed. ALE[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-142 Samsung Business Communications (continued) Timer Name Default Range Unit Description CO CONFIRM TIME 3 0-250 MIN According to MMC 314 CO CO NFIRM ty pe, the outgoing call will be disconnecte d after this timer expires or the outgoing caller w ill hear the confirm tone. CO-CO DISC[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-143 (continued) Timer Name Default Range Unit Description FIRST DIGIT TIME 10 1-250 SEC This timer controls how long the system will wait for dialling to begin before drop ping the dial tone and returning the yo u to error tone. H O K F L AS H M A X T M 120 20-2500 MSE[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-144 Samsung Business Communications (continued) Timer Name Default Range Unit Description MS LED ON TIME 5 1-10 SEC This timer controls the duration a Manu al Sig- nalling key will remain on after use. OFF HOOK RING INT 15 1-250 SEC This timer controls the time between ring bursts to [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-145 (continued) Timer Name Default Range Unit Description TRANSFER RECALL 20 0-250 SEC This timer determines ho w long transferred calls ring before recalling. This is a system- wide timer . TRK AUTOMOH DISC 60 1-25 0 SEC When set to ON, incoming trunk calls are connec[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-146 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 501. Display shows first timer value: AA INT DGT TIME 05 SEC Æ 2) Press V olume button to select timer and press Right Soft button to move cursor . KMMC LOCK OUT TM 060 SEC Æ 3) Enter n[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-147 [502] STATION-WIDE TIMERS Allows certain station timer values to be cha nged on a per -station basis or for all stations. No Item Description 0 NO ANS FWD This timer controls how lo ng the station will ring before For ward on No Answer takes place.(1-250 sec) 1 DTM[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-148 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 502. Display shows: [201] NO ANS FWD 015 SEC Æ 2) Dial station number .(e.g., 205) OR [205] NO ANS FWD 015 SEC Æ _ Press V olume button to select station and press Right Soft button. OR[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-149 [503] TRUNK-WIDE TIMERS Allows certain trunk timer values to be changed on a p er -trunk basis or for all trunks. No Item Description Range 00 ANS.BAK TM ANSWER BACK TIME. This timer is used for certain types of E & M signalling and does not affect normal CO li[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-150 Samsung Business Communications (continued) No Item Description Range 13 DISA ANSWR T his is a delay time to answer the DISA trunk call or to answer the trunk when TRK AUT O ANSWER is set to ON(MMC400). 0-9 SEC 14 CONN DELA Y This is the delay time to connect a voice path when use[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-151 5) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. RELATED ITEMS NONE[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-152 Samsung Business Communications [504] PULSE MAKE/BREAK RATIO Allows the ability to change the value of pulses per second and the duration of the make/break time. This will only af fect rotary dial trunks. No Item Description 0 MAKE/BREAK RA TIO Make/Break ratio of dial puls e(01-9[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-153 [505] ASSIGN DATE AND TIME Allows the system date and time to be set. This will set the system-wide clock. Ty p e Description Range YY Y ear 00-99 MM Month 01-12 DD Date 01-31 W D ay 0-6(0: SUN, 1: MON, 2: TUE, 3: WED, 4: THU, 5: FRI, 6: SA T) HH Hour 00-23 MM Minu[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-154 Samsung Business Communications [506] TONE CADENCE Provides the ability to customize the tone caden ce on a system-wide basis. The system pro- vides 1 1 types of tone and three types of tone provide d from Central Office or a PBX sys- tem can be detected. When changin g the MMC [5[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-155 (unit: milliseconds) TON E ON OFF ON OFF DND/NO MORE TONE 250 250 250 250 ERROR TONE 500 500 500 500 H O LD /C AM P- ON T O N E 500 3500 500 3500 M E SS A GE W A I T T O N E 1000 250 1000 250 RING BACK T ONE 400 200 400 2000 RING T ONE 100 0 3000 1000 3000 TRANSFER[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-156 Samsung Business Communications [507] ASSIGN RING PLAN TIME Use this MMC to program Ring Plans time settings. Ring Plans provide six sep arate ring- ing destinations based on day of the week and time of day . The start time within a plan is the time the system will switch from one[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-157 Ring Plan 1 Ring Plan 1 is the default Ring Plan for each day . If no Ring Plan destination is entered, the operator group is the default des tination. DEFAULT DATA ST AR T : NONE END: NONE A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 507. Display[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-158 Samsung Business Communications [508] CALL COST Set the Call Cost attributes generated by the system during a call. This information can be displayed on the phone during a call or as an SMDR record. No Display Description 0 UNIT COST PER MP When t he system is installed to receive[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-159 [510] SLI RING CADENCE Provides the ability to customize the ring cad ence for single line ports on a system-wide basis. There are five cadences available. When changin g the MMC [510] MMC [510] should not be changed from t he default levels without the ass ist anc[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-160 Samsung Business Communications 4) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. RELATED ITEMS NONE[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-161 [511] MSG WAITING LAMP CADENCE This MMC defines the cadence(flash rate) of single line telephone message waiting lamps on phones connected to systems with an MW SLI card. There are two choices for the MW lamp cadence: continuous and interrupte d. No Item Descriptio[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-162 Samsung Business Communications [512] HOLIDAY ASSIGNMENT This MMC defines up to 60 holiday dates throughout the year . The system will override the normal ring plan for these days and remain in the ring plan associated with the holiday . Dates are entered in a month-day format: fo[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-163 [513] HOTEL TIMER This MMC is where the Hotel timers for guest-rooms are set. These are system-wide timers that affect all rooms. Refer to your Hotel docum entation for more details. No Item Description 0 CHECK OUT TIME If a room is occupied after the checkout time[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-164 Samsung Business Communications [514] TONE SOURCE This program can assign an external tone sour ce(e.g., a music source) instead of the normal system tone(TONE) for certain calls. The tones that can be changed are: No Ty p e 0 BUSY TONE 1 DIAL TONE 2 DND TONE 3 TRANSFER TONE 4 MSG[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-165 [515] DAYLIGHT ASSIGNMENT Defines up to 10 summertime periods. The system time will automatically increase by an hour at 2 a.m. on the assigned S tart date and will automatically decrease by an hour at 3 a.m. on the assigned End date. Dates are entered as follows: [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-166 Samsung Business Communications [600] ASSIGN OPERATOR GROUP Used to assign an operator group for each ring plan. DEFAULT DATA RING PLAN 1-6: 500 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 600. Display shows: OPERATOR GROUP 1:500 2:500 2) Dial the ring plan numbe[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-167 [601] ASSIGN STATION GROUP This MMC is used to build all station groups . There are 40 programmable groups available. The options for setting up these groups are as follows: No Option Description 0 TYPE T his is the type of group you ar e creating and can be one of[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-168 Samsung Business Communications (continued) No Option Description 0 TYPE(contd) d) T he callers place in queue is always maintained. Additional programming for this type of UC D group is in MMC 607. There is a maximum of 20 UCD groups available on a s y s- tem due to availability [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-169 (continued) No Option Description 2 OVERFLOW This is the timer value that will cause unans wered calls to a group to begin also ringing the NE XT POR T(see below) after this timer has elapsed. If set to 000, no overflow will take place. 3 GROUP TRANSFER This is a t[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-170 Samsung Business Communications CONDITIONS y A station can be assigned to all station gr oups. A station group can accommodate up to 32 me mbers . y T o enable off -hook ring for incom ing calls to busy members, set OFFHOOK RING in MMC 300, CUST OMER ON/OFF PER ST A TION, to ON. E[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-171 7) Dial next feature option and continue. OR [505] STN GROUP RING:SEQUENTIAL Press V olume button to select option and press Right Soft button. OR Press Left Soft button to return to step 2. 8) Press T ransfer button to save and exit. OR Press Speaker button to adv[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-172 Samsung Business Communications [602] STATION GROUP NAME Allows the system administrator or technician to enter a name up to 1 1 characters to iden- tify an individual station group. ENTERING CHARACTERS Refer to ‘ENTERING CHARACTERS’ in MMC 104, ST A TION N AME. DEFAULT DATA N[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-173 [603] ASSIGN TRUNK GROUP Allows the assignment of trunks to a specific trunk group or to several trunk groups. This is useful in the programming of LCR when more than one trunk is to be in several dialling plans. There are two dif ferent modes of operation: (1) seq[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-174 Samsung Business Communications 5) Enter valid trunk number .(e.g., 729) OR [9] TRK GROUP MEMBER 01:729 Press V olume button to make selection and press Right Soft button to return to step 2. 6) Repeat steps 1-5 to remove trunk from group 9 if necessary . 7) Press T ransfer button[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-175 [604] ASSIGN STATION TO PAGE ZONE Allows the technician to assign a phone to any of the five internal paging zones. Each page zone can have up to 32 members. A phone ma y be assigned to more than one zone. Page zone(*) will page all external page zones as well as a[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-176 Samsung Business Communications [605] ASSIGN EXTER NAL PAGE ZONE Determines which relays will close when one of the four external page zones is accessed. DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 605. Display shows first page zone: EXT. PAGE [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-177 [606] ASSIGN SPEED BLOCK Provides a means of adding or deleting speed dial blocks to the system or an indi vidual phone. W ith the ability to delete a block or blocks of speed dial, it will not be necessary to waste these on such items as voice mail, DPIMs or stati[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-178 Samsung Business Communications 5) Enter valid number for bins. (e.g., 0-5 for EXT or 00-50 for SYSTEM) FREE LIST:20 EXT205:5 OR Press V olu me button to make selection. OR Press Hold button to delete bin(s). 6) Press T ransfer button to save and exit. OR Press Speaker button to a[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-179 [607] UCD OPTIONS Sets up UCD options when an AA card has b een instal led. MMC 601 m ust have already been used to define a UCD group with an overflow destination of a n AA port or group. (A group is preferred over a port because a group allows multiple paths into[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-180 Samsung Business Communications (continued) No Option Description 04 FINAL DESTINA TION This is the final destination for the caller if not answered by a UCD agent. This destination is only reach ed if(a) the caller dials an exit digit during a message or(b) the retr y count has e[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-181 (continued) No Option Description 09 AUTO LOG OUT This YES/NO option determi nes if a station will automatically log out of the UCD group when the RING NEXT timer expires. This setting will be ignored if the RING NEXT timer is set to 000. 10 ALLOUT Æ FINAL T his Y[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-182 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 607. Display shows: [530] UCD OPTION FIRST MSG :61 2) Press V olume button to select UCD group or dial group number . [542] UCD OPTION FIRST MSG :61 OR Press Left Soft button to position [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-183 [608] ASSIGN REVIEW BLOCK Provides a means of adding or deleting CID revi ew blocks to an individual phone. W ith the ability to delete a block or blocks of CID review , it will not be necessary to waste these on items such as voice mail and DPIMs or phones that do[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-184 Samsung Business Communications [609] CALL LOG BLOCK Provides a means of adding or deleting Call L og blocks for an indi vidual phone. W ith the ability to delete blocks it will not be necessary to waste these on items such as voice mail and DPIMs or phones that do not have displa[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-185 [611] ALLOW TEXT MESSAGING This program allows stations to send text messag es to other stations if they are busy or dur- ing an OHV A. Up to 20 stations can be allowed text messaging. DEFAULT DATA y NOT USED(no text m essaging allowed) y ITP-5012L(Large LCD) keyse[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-186 Samsung Business Communications [612] ALLOW GROUP CONFERENCE This program allows a station to use the Group Conference call feature. Up to 20 stations can be allowed this feature. Each allowed st ation can have up to five pre-programmed con- ference groups. CONDITIONS This feature[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-187 [614] STATION/T RUNK USE GROUP This program allows you to assign stations to station use groups and trunks to trunk use groups. This i s useful if you want to r estrict calling between stations, outgoing calls through a trunk lines, or call answering. CONDITIONS St[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-188 Samsung Business Communications [615] MGI GROUP This program assigns designated MGI ports to sp ecific services. This allows ‘grading’ of MGI card(s) for traffic conditions. The MGI por ts can be segregated into groups. Any en- tries made here may be ineffective if conflicting[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-189 A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 615. Display shows the first available option: USER: LOCAL ITP MODE:SEQUENTIAL 2) Press V olume button to select an user type. Press Right Soft button to move cursor . USER: LOCAL ITP M ODE:SEQUENTIAL 3[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-190 Samsung Business Communications [616] MGI USER This program selects which specific MGI ports will be dedicated on a per-port basis for IP station/trunk devices. If this MMC is not used, allocation of MGI ports will be controlled by MMC 615. By defining dedicated MGI port usage, th[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-191 [700] COPY COS CONTENTS This MMC allows the technician to duplicate classes of service. DEFAULT DATA NONE PROGRAM BUTTONS ‘F’ KEY Used to advance to MMC 701 A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 700. Display shows: COPY COS ITEMS COS01 [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-192 Samsung Business Communications [701] ASSIGN COS CONTENTS Similar to MMC 700 but does not allow a copy comm and. This MMC is primarily used for creating a new class of service(COS). If the unsupervised conference featur e is allowed, a programmed CONF key must be available to allo[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-193 (continued) No Category Des cription 1 USABLE FEA TURE No COS Default Description 20 FEA TURE YES Transfer button 21 FLASH YES T runk flash 22 FO L LO W -M E YES Call for w ard-follow me 23 FORW ARD YES Call for w arding 24 FWDTOVMS YES Call forward to SVM-800 25 G[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-194 Samsung Business Communications (continued) No Category Description 1 USABLE FEA TURE No COS Default Description 53 REM. HOLD YES Remote Hold 54 RNG PLAN YES Ring Mode Change 55 SECURE YES Barge-In secure 56 SET RLOC NO Set Relocation 57 SSPD TOL YES System S peed dial toll check [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-195 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 701. Display shows: COS CONTENTS(01) TOLL LEVEL:A 2) Dial COS.(e.g., 06) OR COS CONTENTS(06) T OLL LEVEL:A Press V olume button to select COS number and press Right Soft button to move cursor . 3) Dial C[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-196 Samsung Business Communications [702] TOLL DENY TABLE Provides a way to make toll restriction(call barring) very easy and flexible. There are 500 entries allowed in the deny table and each entry index can be assigned to a class of service. Each index can have up to 12 digits. W it[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-197 5) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. RELATED ITEMS MMC 703 TOLL ALLOW ANCE T ABLE MMC 704 ASSIGN WILD CHARACTER [703] TOLL ALLOWANCE TABLE Provides a way to make toll restriction very easy and flexible. There a[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-198 Samsung Business Communications 4) Press V olume button to move cursor along line until under toll class mark.(e.g., E). ALOW(001):BCDEFG 202 :0001 00 Enter a 1 for ‘Y es’ or 0 for ‘No’. Press Right Soft button to store and return to step 1. OR Press Left Soft button to re[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-199 [704] ASSIGN WILD CHARACTER Provides flexibility to toll restriction(call barring) when a specific numbering plan is de- sired. There are only three entry tables but more than one digit can be assigned per table if needed. DEFAULT DATA X ENTRIES SET TO 1 Y AND Z EN[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-200 Samsung Business Communications [705] ASSIGN SYSTEM SPEED DIAL Enables the assignment of system speed dialling numbers. There are up to 450 entries available for programming.(or 950 entries if set in MMC 861 SYSTEM OPTIONS) Each speed dial number consists of a trunk or trunk group[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-201 5) If you want to save the speed dial number and name to the CID translation table.(MMC 728) SYS SPEED DIAL ADD CLI XLT ?NO Press the ANS/RLS button and dial 1 for YES. (The speed dial name must exist) 6) Press T ransfer button to save and exit. OR Press Speaker bu[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-202 Samsung Business Communications 3) Enter name using dial keypad and press Right Soft button to return to step 2. SYS SPEED NAME 505:TELECOMS OR Press the F key to return to MMC 705, step 3. SYS SPEED DIAL 505: 4) If you want to save the speed dial number and name data to the CLI t[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-203 [707] AUTHORIZATION CODE Enables the authorization feature on a per -cl ass of service selection. There are 500 avail- able entries. Authorization codes must be 4-10 digits long. DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button and enter 707. D[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-204 Samsung Business Communications [708] ACCOUNT CODE Enables the account code entry feature. There are 999 available entries. DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button and enter 708. Display shows: ACCOUNT CODE 0 01: 2) Dial code index number .(e.g., 005)[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-205 [709] TOLL PASS CODE/SPE CIAL CODE TABLE This MMC provides a means to program trunk code tables as described below . No S pecial Code Description 0 PBX CODE This table contains up to five entries and is used to identify the trunk access codes needed for toll restri[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-206 Samsung Business Communications 4) Enter via dial keypad the desired access/feature code.(e.g., 91 1) TOLL OVERRIDE 3:911 Press Right Soft button to enter and return to step 3 and enter more entries. 5) Press T ransfer button to save and exit. OR Press Speaker button to advance to[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-207 [710] LCR DIGIT TABLE The LCR DIGIT T ABLE contains all numerical digits for the completion of outgoing call placement. This table works in conjunction with LC R ROUTE T ABLE, LCR TIME T A- BLE and LCR MODIFY DIGITS T ABLE. There is a maximum 2000 entries with a di[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-208 Samsung Business Communications [711] LCR TIME TABLE This table, through the LCR ROUTES, allows calls placed at any given time of day to use the least cost trunk route that is available. When LCR ROUTE ADV ANCE is allo wed, it is possible for calls to be placed on more expens ive [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-209 [712] LCR ROUTE TABLE The LCR ROUTE T ABLE is responsible for selecting a specific trunk group in the comple- tion of an outward bound call. This table works in conjunction with LCR DIGIT T ABLE, LCR TIME T ABLE, LCR COS T ABLE and LCR MODIFIED DIGITS T ABLE. After[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-210 Samsung Business Communications 6) Dial MODIFY DIGITS index number .(e.g., 050) OR LCR ROUTE (05:2) C:4 G:801 M:050 Press V olume button to selected index number and press Right Soft button to move cursor . OR Press Right Soft button to skip step and move LCR ROUTE (05:2) C:4 G:80[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-211 [713] LCR MODIFY DIGIT TABLE This program is sometimes referred to as Outgoi ng Dial Rules. It enables the system to add or delete a digit string or singular digit if needed to com plete a call. W ith these digits in- serted, a long distance call will be placed ove[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-212 Samsung Business Communications 5) Enter digits to be appended.(e.g., 45678) OR LCR MODIFY (005) A:_ Press Right Soft button to skip step or to store infor- mation and return to step 2. 6) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. REL[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-213 [714] DID NUMBER AND NAME TRANSLATION Assigns an incoming DID call to a specific ring plan destination. It also provides a call waiting option, if needed, so that a second inco ming DID call can be received. The table is also used to define which MOH source a calle[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-214 Samsung Business Communications DEFAULT DATA INDEX DIGIT MOH PRI 1-6 CW MC DC NAME 001 2*** NONE NO B N 99 0 NONE 002 3*** NONE NO B N 99 0 NONE 003 5*** NONE NO B N 99 0 NONE 004 8*** NONE NO B N 99 0 NONE A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 714. Displa[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-215 7) Enter call wait option via dial keypad. (1 for YES, 0 for NO) DID DIGIT (005) CW:N MC:99 DC:0 OR Press V olu me button to make selection and press Right Soft button to advance to next step. 8) Enter maximum call count via dial keypad.(00-99) OR DID DIGIT (005) C[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-216 Samsung Business Communications [715] PROGRAMMED STATION MESSAGE Allows custom messages to be programmed or default messages to be changed. ENTERING CHARACTERS Refer to ENTERING CHARACTERS in MMC 104, ST A TION NAME. There are 15 messages in the system: MESSAGES 01-10 are 16-chara[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-217 [716] UK LCR OPTION This MMC provides UK LCR options. No Option Description 0 NETWORK CODE This table is used to network access code when the call is routed to the secondary net work. This table contains up to 16 entries. Each code has 4 d i gi t s ma xi m um i n l[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-218 Samsung Business Communications 5) Enter use option number .(0-3) OR NETWORK CODE 02:1234 USE:CCC Press V olume button to make selection and press Right Soft button to save and return to step 3. 6) Press T ransfer button to save and exit. OR Press Speaker button to advance to next[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-219 [717] UCD AGENT ID This MMC defines UCD agent ID numbers or PIN numbers. These numbers are used to log UCD agents into the UCD groups. There are 100 available entries and each entry is tied to a specific UCD group. Agent ID codes can be up to 4 digits long. DEFAULT[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-220 Samsung Business Communications [718] MY AREA CODE This MMC defines the home area code and count ry code. This information is used for caller ID and ISDN calls in defining the ar ea code on incoming calls. This MMC removes the local area code to allow callback without digit modifi[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-221 [719] IDLE DISPLAY This program allows you to enter guidance data to be displayed on large LCD phones. ENTERING CHARACTERS Refer to ‘ENTERING CHARACTERS’ in MMC 104, ST A TION N AME. DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button and ente[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-222 Samsung Business Communications [720] COPY KEY PROGRAMMING Provides a tool for duplicating key assignment s from one phone to another . This can be done on a per -station basis or on all stations, but not o n a group of stations. A limitation is that the original and target phones[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-223 [721] SAVE STATION KEY PROGRAMMING Provides a service tool which minimizes the accidental loss of programmable buttons on phones. First the data is saved and then the sta tion can be replaced with another station type or the keys can be reprogrammed to other featur[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-224 Samsung Business Communications [722] STATION K EY PROGRAMMING Allows the customizing of programmable buttons on specific phones and add-on modules (AOMs). For phones, buttons 1 and 2 are set as CALL buttons b y default. For AOMs, all buttons are set as DS keys by default. Feature[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-225 (continued) Feature Des cription Feature De scription CA D CALL ACTIVITY DISPLA Y OHV A OFF-HOOK VOICE ANNOUNCE CALL CALL BUTTON OPER OPERA TOR CA MP ST A TION CAMP-ON PA G E PA G E CA NMG MESSAGE CANCEL PA G P K PICKUP P AGE HOLD CBK CALLBACK PA R K CALL P ARK ORB[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-226 Samsung Business Communications (continued) Feature Des cription Feature Description DT DTS KEY ST A TE SET EXECUTIVE ST A T E ECT EXPLICIT CALL TRANSFER EP EST ABLISHED CALL PICKUP STORE STORE DISPLA YED NUMBER EXTMIC EXTERNAL MIC SYSALM SYSTEM ALARMS TCLIP T EMP CLIP FAU TO FORC[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-227 DEFAULT DATA For phones, buttons 1 and 2 are set as CALL bu ttons by default.(Other settings depend on the keyset type.) For AOMs, all buttons are set as DSS buttons by default. A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 722. Display shows: [201[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-228 Samsung Business Communications [723] SYSTEM K EY PROGRAMMING This MMC is similar to MMC 722, S tation Key Programming, except that changes are made system-wide rather than on a per-station basis. Features are entered via the dial key- pad by pressing numbers as shown in the table[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-229 DEFAULT DATA SEE DEF AUL T DA T A IN MMC 722 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 723. Display shows: TYPE:24 BTN SETS 01:CALL1 Æ 2) Enter type of set via dial keypad.(e.g.,1) OR TYPE:12 BTN SETS 01:CALL1 Æ Press V olume button to make se[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-230 Samsung Business Communications [724] DIAL NUMBERING PLAN This MMC allows the technician to change di rectory numbers for stations, trunks, station groups, trunk groups and feature access codes. The s ystem can be pre-programmed with default 3- or 4-digit numbering for stations , [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-231 (continued) No T y pe of Dial No Description 10 VIRT EXT DIAL NO This is w here virtual station directory numbers are changed or assigned. Default: SL T : 3501- 3508, DGP: 3401-3416 1 1 MGI DIAL NO. T his is where MGI port directory numbers are changed or assigned.[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-232 Samsung Business Communications Feature Code Assignments and Default Feature Default Description ABAND 64 ABANDONED CALL ABS NONE ABSENCE ABW NONE AGENT BUSY/WRAP UP ACCT 47 ACCOUNT ALLCLR NONE ALL CLEAR AUTH NONE AUTHORIZA TION CODE BARGE NONE BARGE-IN BILL NONE BILL(Hotel Featur[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-233 (continued) Feature Default Description GRPK 66 GROUP PICKUP HDSET NONE HEADSET MODE HLDPK 12 HOLD PICKUP HOLD 1 1 HOLD HOTEL NONE HOTEL( Hotel Feature) ICONF NONE ISDN 3-P ARTY CONFERENCE IDISC NONE ISDN 3-P AR TY DISCONNECTION IG 53 IN/OUT GROUP IHOLD NONE ISDN 3[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-234 Samsung Business Communications (continued) Feature Default Description SETMG 41 SET MESSAGE W/O RING SLOCA T NONE ST AFF LOCA TOR(Hotel Feature) SL T ALM NONE EASY ALARM SET T O SELF ST A TION SL TMMC 15 NORMAL PHONE PROGRAMMING SNR 17 SA VED NUMBER REDIAL SPEED 16 SPEED DIAL SRE[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-235 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 724. Display shows: STN DIAL NUM:C1 S2-P01:201 Æ 2) Dial option number to make selection.(e.g., 06) OR FEAT DIAL NUMBER ABAND :64 Æ _ Press V olume button to make selection and press Right Soft button [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-236 Samsung Business Communications [725] SMDR OPTIONS Allows the system administrator to select th e information printed on the SMDR report. The following options may be selected: No Option Default Description 00 P AGE HEADER YES This option determines whether a page header will prin[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-237 (continued) No Option Default Description 15 INCOMING ANSWER NO If this option is set to YES, the duration of calls ringing before being answered w ill print on SMDR. 16 INTERCOM CALL NO This option determines w hether intercom calls w ill print on SMDR. 17 KEY MMC[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-238 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 725. Display shows: PAGE HEADER PRINT: YES 2) Dial the option number .(e.g., 01) OR LINE PER PAGE 60 LINE/PAGE Use the V olume buttons to scroll through the options and press Right Soft b[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-239 [727] SYSTEM VERSION DISPLAY This MMC is used for system version display only .(READ ONL Y) The displays depend on which modules are included in the system DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button and enter 727. Display shows: MP10-MAIN[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-240 Samsung Business Communications [728] CID TRANSLATION TABLE Allows the system administrator or technici an to associate a CID number received from the central office with a name programmed in this translation table. If t here is no match be- tween a received number and a name in t[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-241 [740] STATION PAIR Assigns a secondary station to a phone. This secondary station can be a keyset or single line phone. The secondary station assumes the Call Forwarding, Class of Service, LCR Class, and DND attributes of the primary sta tion. The secondary station[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-242 Samsung Business Communications [746] COSTING DIAL PLAN The COSTING DIAL PLAN is used to analyze the leading dialled digits of a dialled num- ber and determine what DIAL PLAN it is to follow . Data entry for this program is in three fields: ENTR Y , DIGITS and COST RA TE table ref[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-243 DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 746. Display shows: COST DP (0 01) DIGIT: 2) Dial CALL COST entry .(e.g., 005) OR COST DP (005) DIGIT:_ Press V olume button to select entry and press Right Soft button to move cursor [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-244 Samsung Business Communications [747] RATE CALCULATION TABLE The RA TE CALCULA TION T ABLE is used to define the billing charges for each COST RA TE. These rate tables correlate with the T r unk Cost Rate and the Costing Dial Plan. There are eight call costing rates. Each rate has[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-245 3) Dial option number 0-4.(e.g., 1) OR COST RATE (3) 1ST COST:000 Press V olume button to select option and press Right Soft button to move cursor . 4) Enter data via dial keypad.(e.g., 125=1.25) OR COST RATE (3) 1ST COST:125 Press V olume button to select data and[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-246 Samsung Business Communications [750] VM CARD RESTART This MMC is used for the Samsung Built-In V oice Mail card. There are four options available in this MMC: No Option Description 0 MBX DOWNLOAD When the Built-In V oice Mail module starts, p art of the power up procedure will do[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-247 A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 750. Display shows: M BX DOWNLOAD NO 2) Press V olume button to make selection and press Right Soft button. VM RESTART RESET NOW ? NO 3) Press V olume button to make selection and press Right Soft butto[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-248 Samsung Business Communications [751] ASSIGN MAILBOX This MMC is only used for the Samsung Built -In V o ice Mail card. I t assigns mailboxes to each station or group as required. During V o ice Mail card power up, mailboxes will be cre- ated for each directory number with a ‘YE[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-249 [752] AUTO RECORD This MMC is only used for the Samsung Built-In V oice Mail card. Specific stations in the phone system can be assigned to automatically record conversations. When this option is set, all incoming, all outgoing, or all calls(incoming and outgoing) [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-250 Samsung Business Communications 4) Dial VM number via dial keypad. OR AUTO RECORD PORT:2 09 CALL:I Press V olume button to make selection and press Right Soft button to move cursor . 5) Dial call type via dial keypad.(0: I, 1: O or 2: B) OR AUTO RECORD PORT:209 CALL:B Press V olum[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-251 [753] WARNING DESTINATION This MMC is only used for the Samsung Built-In V o ice Mail card. It provides an em er- gency destination for calls destined for the card if the card is removed or is offline. In addition, any calls that are forwarded to the card will not [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-252 Samsung Business Communications [754] VM HALT This MMC is only used for the Samsung Built-In V oice Mail. It is used to halt the V oice Mail Module. If the V oice Mail module is halted by using this MMC, system has to restart to use the V oice Mail m odule again. At that time, ‘[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-253 [755] VM ALARM This MMC is only used for the Samsung Built-In V oice Mail. It will generate an alarm message in the mailbox defined in MMC 751 when ever the V oice Mail disk drive reaches a threshold. The threshold is measured as a percentage of capacity . This mea[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-254 Samsung Business Communications [756] ASSIGN VMMOH This MMC is only used for the Samsung Built-In V oice Mail. It is used to assign each port a Music-On-Hold source for the system from a sound file located on the V oice Mail card hard disk drive. The 100 available sound files are [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-255 [757] VM IN/OUT This MMC is only used for the Samsung Built -In V o ice Mail. It is used to assign each V oice Mail port as used for incoming, outgoing or both-way calls. This MMC must support outgoing calls if of f-premises notification(beeper , outbound follow me[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-256 Samsung Business Communications [758] VM DAY/NIGHT This MMC is only used for the Samsung Built-In V oice Mail. The module can operate in either a DA Y or NIGHT operating mode. The mode determ ines what main menu greetings and options are played to callers and can cha nge automatic[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-257 [759] CLI RINGING This MMC assigns a specific CID number received from the central office to a specific ring plan destination. Also allows you to reject a specific CID number and assign priorities. There are 9 priority levels: priority 1 is the highest and priority[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-258 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 759. Display shows: CLI RINGING(001) CLI: 2) Dial entry number .(e.g., 005) OR CLI RINGING(005) CLI:_ Press V olume button to make a selection and press Right Soft button to move cursor .[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-259 [760] ITEM COST TABLE This MMC provides a means to assign a code to a billable item along with a 10-character name for the item. There are a maximum of 10 0 entries(00 to 99) in the table with item 00 reserved as the code for room deposits, 01 r eserved as the code[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-260 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 760. Display shows: ITEM CODE (00) NAME:RM Deposit 2) Enter valid code number(e.g., 02) via dial keypad. ITEM CODE (02) NAME: OR Press V olu me button to make selection and press Right S[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-261 [761] TAX RATE SETUP This MMC allows the technician to set up th e eight tax rates used in MMC 760. Each tax rate may be defined as a fixed value or as a pe rcentage of the item cost. In addition, a 10- character name may be used to define the reas on for the tax. [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-262 Samsung Business Communications 4) Enter the tax rate or value via dial keypad. OR TAX RATE (2) TYPE:C VAL:01.25 Press V olume button to make selection. If valid entry , system advances cursor . 5) Enter name and press Right Soft button to return to step 2. TAX RATE (2) NAME:MIA B[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-263 [762] ROOM COST RATE This MMC allows the technician to set up the cost rates for a week. Each room cost rate can be assigned with a percentage of the actual room cost from Sunday to Saturday . EXAMPLE: If you set SUN: 150%, 1. MON: 100%, 2.TUE: 090% . Then, if you [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-264 Samsung Business Communications [763] SECOND LCR This MMC allows the technician to in put the Extended LCR information table. Max table index is 200. This table have transl ation and route inform ation for input digits. The last table(index 200) has only ‘NEXT ROUTE’ option. T[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-265 5) Enter OUT DIGIT maximum 16 digits, and press Right Soft button to move cursor . (001)O UT DI GIT 7500 6) Enter USE LCR NUM option number([2]). OR (001)USE LC R NUM Press V olume button to select USE LCR NUM and press Right Soft button to move cursor . 7) Enter U[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-266 Samsung Business Communications [800] ENABLE TECHNICIAN PROGRAM Used to open and close technician-level programming. If programming is not opened and an attempt is made to access a system MM C, an error message will be displayed. CONDITIONS A 4-digit passcode is required to access[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-267 [801] CHANGE TECHNICIAN PASSCODE Used to change the passcode which allows access to MMC 800, Enable T echnician Pro- gram, from its current value. CONDITIONS The passcode is four characters long. Each char acter can be digits 0-9. The current or old passcode is req[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-268 Samsung Business Communications [802] CUSTOMER ACCESS MMC NUMBER Allows the System Admini strator(customer) to have acc ess to certain MMCs. For example, it is required that the customer has access to MMC 102, Call Forward, for call forwarding but it is not required that the custo[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-269 [805] TX LEVEL AND GAIN Allows the system administrator to set the base level of TX volume on phones. There are eight levels that can be controlled by the V olume buttons on phones, and 10 co ntrollable levels in the system. This MMC allows the system administrator[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-270 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 805. Display shows: TX LEVEL CONTROL LEVEL 0 Æ 0 2) Press V olume button to make selection(0-3) and press Right Soft button to move cursor . TX LEVEL CONTROL LEVEL 1 Æ 1 3) (When the T[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-271 [806] CARD PRE-INSTALL Allows the pre-programming of a card slot for a specific card type. A card inserted into a system will not be recognized by the system until it is enabled using this MMC. Cards in- stalled using this MMC will not be assigned in the system num[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-272 Samsung Business Communications Press V olume button to make selection and press Right Soft button. 5) Dial 1 for YES to reset card or dial 0 for NO. OR C:1–S:6 ARE YOU SURE?NO Press V olume button to make selection and press Right Soft button.[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-273 6) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. RELATED ITEMS MMC 724 DIAL NUMBERING PLAN [807] PHONE VOLUME CONTROL Allows the system administrator to set phone volume levels. Phone Volume Lev el FX No T ype No T ype 0 K[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-274 Samsung Business Communications DEFAULT DATA DEPENDS ON PHONE TYPE(SHOWN FOR 21D) 21D FX T ype Default T ype Default KEY TONE VOL 1 LINE VOLUME 3 SIDETONE VOL 1 SPEAKER VOLUME 14 HANDSET TX 4 NOR.LP A TTEN 4 MIC TX LEVEL 3 MIC LP A TT EN 5 NOISE GUARD 8 ACOU DECOUPL 8 NOISE THRES [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-275 [810] HALT PROCESSING Used only in the event that all data processing needs to be stopped either in a single cabinet slot or in the entire system. DEFAULT DATA PROC A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 810. Display shows: HALT/PROCESSING C[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-276 Samsung Business Communications [811] RESET SYSTEM Provides a means of restarting the system. The system can simply be reset or it can be reset and all memory cleared to default values. Ex treme care should be taken when using this MMC. If the system is restarted, all voice/da ta [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-277 [812] SET COUNTRY CODE Selects the country for correct sy stem programming and operation. When changin g the MMC [812] ‘ MMC [812] SET COUNTR Y CODE ’ should not be used from the default levels without the assistance of t he local SAMSUNG distributor . DEFAULT [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-278 Samsung Business Communications [813] HOTEL OPERATION Allows the installing technician to enable the HOTEL feature. DEFAULT DATA DISABLE A C T I O N D I S P L A Y 1) Press T ransfer button and enter 813. Display shows: HOTEL OPERATION D ISABLE 2) Dial 1 for ENABLE or 0 for DISABLE[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-279 [815] CUSTOMER DATABASE COPY This enables the on-board customer datab ase(SRAM) to be copied to the MC Data- base(MCDB) and also allows the MCDB datab ase to be copied to the SRAM. A daily save can be programmed to automatically save the SRAM to the MCDB. This ensu[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-280 Samsung Business Communications 2) Press Right Soft button to move cursor . CUST DBASE:MCDB S:12/01/01 00:00 3) Press V olu me button to make selection and press Right Soft button to move cursor . CUST DBASE:MCDB CLEAR SMDB :NO 4) Press V olu me button to select YES or N O and pre[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-281 [818] PROGRAM DOWNLOAD Change the system version by downloading th e new version stored on the MC card to the APP/SYS/DR V/WEB/RUT /MSP/CSP and TEPRI cards. Option Description APP T o upgrade ap plication (including MP and VM module) SYS Include all modules. (?) DR[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-282 Samsung Business Communications [819] MC FILE CONTROL Displays the size(in bytes) of various system program files on the MC card. Files included in MC card are described below: File Name Description Star t up .i ni If user designates an MCP program in MMC 818, related data are sav[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-283 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 819. Display shows: S tartup.ini sz:512 bytes 2) Press V olu me button to confirm program type C s10v101.pkg sz:14418432 bytes 3) Press T ransfer button to save and exit. OR Press Speaker button to advan[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-284 Samsung Business Communications [820] ASSIGN SYSTEM LINK ID This MMC is used to assign the system link ID for PRI and V oIP networking. Up to 100 link IDs can be entered including SELF ID. In a ddition, each Link ID is associated with the IP address and IP address type of the MCP [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-285 [821] ASSIGN NETWORK TRUNK Assigns the Q-signalling PRI trunk for networki ng. I t is assigned data on a per-TEPRI card basis. DEFAULT DATA NORMAL A C T I O N D I S P L A Y 1) Press T ransfer button and enter 821. Display shows: [701] Q-SIG TRK NORMAL 2) Enter firs[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-286 Samsung Business Communications [822] VIRTUAL EXTENSION TYPE Assigns the virtual extension port type. The virtual extension port types are followed: No Ty p e Desc ription 00 SL T Emulates SLI port 01 24 BTN SET 24 buttons pho ne 02 12 BTN SET 12 buttons pho ne 03 7 BTN SET 7 butt[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-287 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 822. Display shows: [3501]PORT TYPE SLT 2) Enter virtual extension number. OR [3501] PORT TYPE S LT Press V olume button to make selection and press Right Soft button to move cursor . OR Select all ports[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-288 Samsung Business Communications [823] ASSIGN NETWORK COS Assigns the class of service for networking. No Option Default Description 01 CALL OFFER Y Call Offer 04 CC SIG CONN Y CC Retention of Signal Con nection 05 CC SVC RETN Y CC Service Retention 06 CCBS N Call Completion to Bus[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-289 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 823. Display shows: NETWORK COS (01) 01:CALL OFFER :Y 2) Dial the class of service number .(01-30) OR NETWORK COS (02) 01:CALL OFFER :Y Press V olume button to select and press Right Soft button to move [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-290 Samsung Business Communications [824] NETWORK DIAL TRANSLATION Assigns the digit translation table used fo r networking. Generally , under networking condi- tions, you must dial the node ID and extension num ber to call the another node extension. In this MMC, the system provides [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-291 7) Enter YES/NO to assign Mailbox to remote extension automatically . 01:601 Æ 60201 DISP:Y MBX:N OR Press V olu me button to select and press Right Soft button to move cursor . 8) Press T ransfer button to save and exit. OR Press Speaker button to advance to next[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-292 Samsung Business Communications [825] ASSIGN NETWORKING OPTIONS Assigns the options used for networking. No Option Description 0 ADD NUMBER TO NAME Assign to include the extension number in th e name field of Q-SIG standard message. 1 USE REMOTE VM Assign to use SVMi on remote s y[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-293 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 825. Display shows: A DD NUMB TO NAME YES 2) Dial the option number . OR USE REMOTE VM N O Press V olume button to select and press Right Soft button to move cursor . 3) Dial 1 for YES or 0 for NO. OR US[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-294 Samsung Business Communications [826] ASSIGN SYSTEM REFERENCE CLOCK The system clock may be synchronized with an external clock source from the TEPRI or BRI card, or it can use the internal clock source. This MMC can assign the system clock source pr iority when the external clock[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-295 [829] LAN PRINTER PARAMETERS This program sets the various parameters required for printing to a LAN-connected device. The data listed below can be printed. 01. SMDR 02. UCD REPOR T 03. TRAFFIC REPOR T 04. ALARM REPOR T 05. UCD VIEW 06. PERIODIC UCD 07. HOTEL REPOR[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-296 Samsung Business Communications DEFAULT DATA SEE DESCRIPTION A C T I O N D I S P L A Y 1) Press T ransfer button and enter 829. Display shows: [01] DATA TYPE SMDR 2) Enter type of data to be printed. OR [02] DATA TYPE UCD REPORT Press V olume button to select the type and press th[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-297 [830] ETHERNET PARAMETERS This MMC provides a mean to configure the Internet Protocol(IP) addressing of the MCP card. No Parameter Des cription 00 SYST EM IP ADDR S pecifies the IP address for the MCP card. 01 SYST EM GA TEW A Y Specifies the designated gateway IP [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-298 Samsung Business Communications ETHERNET P A RAMETERS - The first three parameters: SYST EM IP ADDR, SYSTEM GA TEWA Y , and SYS- TEM NET MASK are stored separately fr om the main system database and thus will not be defaulted when MMC81 1 ‘ CLEAR MEMORY ’ is performed. Further[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-299 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 830. Display shows the system IP address. S YSTEM IP ADDR 165.213. 97.185 2) Press V olume button to make selection and Press Right Soft button to move cursor . SYSTEM IP ADDR 1 65.213. 97.185 3) Using t[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-300 Samsung Business Communications [831] MGI PARAMETERS This MMC provides a mean to configure the Internet Protocol(IP) addressing of the MGI card(s) in the system. No Parameter Des cription 0 IP ADDRESS Specifies the IP address for the MGI card. 1 GA TEWA Y Specifies the designated [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-301 CONDITIONS This MMC cannot be accessed unless there is an MGI card installed in the system. DEFAULT DATA IP ADDRESS: 1.1.1.1 GA TEW A Y : 1.1.1.1 SUB MASK: 255.255.255.0 IP TYPE: PRIV A TE IP ONL Y PUBLIC IP: 1.1.1.1 PUB POR T : 00000 VERSION: V4 CARD RESET : NO IP[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-302 Samsung Business Communications [832] VoIP ACCESS CODE Provides a means to apply the Internet Prot ocol(IP) address to the V o IP gateway . This MMC also assigns the number of channels that can be used for IP faxes. T ABLE(00~62) : Outbound or Inbound table used for specific acces[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-303 DEFAULT DATA ACCESS DGT : 00~09(digits 0~9), 10~62 NONE DGT LENGTH: 1 DEL.LENGTH: 1 INSER T DGT : NONE IP T ABLE 1: 00 IP ST AR T : NONE SER VER USE: NO A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 832. Display shows the outbound and first access [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-304 Samsung Business Communications [833] VoIP IP TABLE This MMC provides the IP addresses in tables pointed to by the V oIP code entry(MMC 832). There are 63 tables with up to 16 entri es each. The destination IP address is required to route dialled digits based on the access code a [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-305 [834] H.323 OPTIONS This MMC provides various V oIP support options. The options set in this MMC apply sys- tem wide. No Parameter Description Default 00 GA TEW A Y CALL ID Numeric identif ier for system(up to 12 digits) 1234 01 H.323 FAST SETUP Enables or disables[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-306 Samsung Business Communications DEFAULT DATA SEE DESCRIPTION A C T I O N D I S P L A Y 1) Press T ransfer button and enter 834. Display shows the first option. G ATEWAY CALL ID 1234 2) Enter H.323 option number(00-20) via dial keypad. H.323 FAST SETUP D ISABLE OR Press V olu me bu[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-307 [835] MGI DSP OPTIONS This MMC provides various MGI DSP options. No Parameter Description Default 00 CODEC-FRAME Selects which audio CODEC compression will be used and the transmission interval time of V oIP p ackets gen- erated by the MGI card. MGI3 card supports [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-308 Samsung Business Communications (continued) No Parameter Description Default 13 DT MF TYPE T here are two types of DTMF transmission: INBAND, which is industry standard(H.245) type DTMF transport, and OUTBAND which is a Samsung propr ietary method. OUTBAND 14 TOS FIELD An 8-bit bi[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-309 Press V olume button to make selection and press Right Soft button to move cursor . 4) Enter MGI DSP parameter . OR MGI3:CODEC-FRAME G .729A –20 MS Press V olume button to make selection and press Right Soft button to save and return to step 3. 5) Press T ransfer[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-310 Samsung Business Communications [836] H.323 GK OPTIONS Provides a means to set the H.323 gatekeeper pa rameters for an optional, external industry- standard H.323 network gatekeeper , using Re gistration, Admissions and Status signalling (RAS). The settings apply system wide. When[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-311 No Parameter Description Default 13 GRQ SEND Select ON or OFF fo r use of Gatekeeper RAS Re- quest(GRQ) messages. OFF 14 USE MUL TI E.164 When this option is set to ENABLE, t he E.164 iden ti- fier can be assig ned. DISABL E 15 E.164 LIST S This is th e E.1 64 i de[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-312 Samsung Business Communications [837] SIP OPTIONS This MMC permits the adjustments of opti onal Session Initiation Protocol(SIP) trunk pa- rameters. The MCP supports SIP and H.323 on a per -call-per -port basis. The settings are system wide. When changing IP When changing any IP a[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-313 (continued) No Parameter Description Default 14 PROVISIONAL TIME After receiving the Provision Response, the User Agent waits for this length of time until Timeout ends. The range is 0~999900 ms. 180000 m 15 INV . NO RESP TIME Before sending C anc el for the Invite[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-314 Samsung Business Communications (continued) No Parameter Description Default 3 8 S I P REGISTERED Display the status of registration to the SIP Server. NO 39 GW SERVICE When usi ng SIP Server , if this option is ENABLE, then register by user and if DISABLE then register by system [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-315 4) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. RELATED ITEMS MMC 323 CALLING P AR TY NUMBER MMC 405 TRUNK CO TEL NUMBER MMC 306 TRUNK RING ASSIGNMENT MMC 714 DID NUMBER AND NAME TRANSLA TION MMC 724 DIAL NUMBERING PLAN M[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-316 Samsung Business Communications [839] SIP USER This MMC is used to register sip user and password. DEFAULT DATA A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 839. Display shows the first table number . R EG-01 : USER NUM 2) press Right Soft button to move cursor .[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-317 [838] PRIVATE IP ADDRESSES This MMC is used to select which SYSTEM IP Address(PRIV A TE or PUBLIC) is used to connect other devices via an H.323 or SIP trunk. The device that use the PRIV A TE IP Ad- dress assigned in this MMC, the PRIV A TE SYSTEM IP Address will [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-318 Samsung Business Communications [840] IP PHONE INFORMATION This MMC provides a means to register IP phones with the Of ficeServ 7100 system. Dur- ing registration, the IP and MAC addresses are also registered. The User ID and Password must match the table entry in this MMC for th [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-319 (continued) No Option Description Default 1 1 JITT ER BUF Decides the minimum time to consider delay for jitter adjustment. This data uses MMC 841 ITP DSP P ARA DOWN = PHONE DA T A only . The range is 10~90 ms. 20 m 12 TOS FIELD An 8-bit binar y value that will be [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-320 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 840. Display shows: [3 201]USER ID 3201 2) Enter IP phone number via dial keypad. OR [3210]U SER ID 3210 Press V olume button to make selection and press Right Soft button to move cursor[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-321 [841] SYSTEM IP OPTIONS This MMC provides various proprietary Sa msung V oIP and IP integ ration options. The options set in this MMC apply system wide. No Option Description Default 00 PHONE VERSION Sets running IP-based phone and ne w phone soft- ware version wit[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-322 Samsung Business Communications (continued) No Option Description Default Sets CTI link via LAN option with the system. 0 S MD R R E PO RT : Sets YES or NO for SM DR data to CTI link via LAN. NO 1 UCD REP OR T : S e t s YES or NO for UCD data to CTI link via LAN. NO 04 CTI LINK OP[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-323 (continued) No Option Description Default 08 ITP TX GAIN/MIC Sets IP-based phone MI C gain valu e of each level. Depends on country 09 ITP RX GAIN/SPKR Sets IP-based phone SPKR gain value of each level. Depends on country Sets IP-based phone software upgrade option[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-324 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 841. Display shows the first available option. P HONE VERSION LARGE DGP: 0000 2) Enter option category number 0-13 via dial Keypad.(e.g., 2) ITP REGISTRATION T YPE: SYS PSWD OR Press V ol[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-325 [845] WLAN PARAMETERS This MMC modifies the WLAN parameters. The SYSTEM KEY is used internally to dis tinguish between systems when registering a terminal. The default value is ‘00000’, but this must be changed to another value to enable the use of WLAN termina[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-326 Samsung Business Communications (continued) No Parameter Description Default 07 VERSION WLAN module version. V e r s i o n 20 MAX AP CH. Set the maximum channel nu mber of AP 0 0 2 1 W L AN S WT C H S up p or t W LA N sw it c h fu n ct i o n DISABLE SIP P ARAMETER No Parameter Des[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-327 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 845. W LAN: SYSTEM ID WBS24 2) When the cursor is on WLAN, press V olume button and select WLAN, WBS, or SIP . W LAN: SYSTEM ID WBS24 3) Press Right Soft button to move to the SYSTEM ID. When the cursor [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-328 Samsung Business Communications 5) Set the items below at the WBS24 menu. The se- lected WBS is as set in MMC 849(SELECT AP TYPE option) i.e. CWBS=COMBO WBS, BWBS=BASIC WBS. Register the WBS24 IP ADDRESS. CWBS1: IP ADDR 0. 0. 0. 0 Register the WBS24 NET MASK. CWBS1: NET MASK 255.2[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-329 Register the RE-TRANS T4. The time the User Agent Server waits after receiving the ACK message. SIP : RE-TRANS T4 005000MS Based on the RFC2543 spec ification. The range is 0-9900 ms.(Default: 5000 ms) Register the GEN RING TM. The server retransmits the response f[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-330 Samsung Business Communications [846] WIP INFORMATION This MMC sets up the WIP-5000M wireless terminal information. No Parameter Description Default 00 REGIST ERED Sho w s if the terminal is registered. NO 01 LOCA TED Shows if the terminal is connected to the system. DET ACH 02 PH[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-331 Displays the location of the registered terminal. [3301] LOCATED DETACH Displays the PHONE TYPE of the registered termi- nal. [3301] PHONE TYPE Displays the WLI NUMBER of the registered ter- minal.(currently not used) [3301] WLI NUMBER Displays the WBS NUMBER of th[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-332 Samsung Business Communications [848] WLAN IP/MAC LIST This MMC is used when viewing the IP list assigned to WLAN, or when creating a new IP list. This IP address is automatically assi gned to WIP-5000M during a new registration procedure. If the IP address is already assigned, th[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-333 [849] WLAN CONFIGURATION This MMC is used to set the WLAN configuration. Parameter Description REGISTER V oWLAN Enable or disa ble registration of new WIP-5000M mobile phone. WIP REGIST CLEAR Used to clear the registration of WIP . FORCED mode clearing is used when[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-334 Samsung Business Communications 6 ) Enter WEP KEY values wh en the WBS WEP SER - VICE is enabled.(13 characters only) W EP KEY 7 ) Select ENAB LE to use the static WBS IP . S TATIC WBS IP DISABLE 8 ) Select ENAB LE to use the static WIP IP . S TATIC WIP IP DISABLE 9 ) Select AP TY[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-335 [850] SYSTEM RESOURCE DISPLAY This MMC is used for system resource disp lay .(used and free resources) This is a READ- ONL Y MMC. 0. DTMFR DSP’S 1. CID DSP’S 2. R2MFC DSP’S 3. CONF GROUP’S DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer butto[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-336 Samsung Business Communications [851] ALARM REPORTING This MMC is used to view , store, print or clear system alarms. T wo levels of faults are dis- played via an alarm code: major alarms and minor alarms. Major alarms codes are usually service affecting and require a certified te[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-337 A C T I O N D I S P L A Y 1) Press T ransfer button and enter 851. Display shows: SYS ALARM REPORT V IEW ALARMS 2) Enter desired option. OR SYS ALARM REPORT V IEW ALARMS Press V olume button to make selection and press Right Soft button to move cursor . 3) System d[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-338 Samsung Business Communications [852] SYSTEM ALARM ASSIGNMENTS This MMC allows the assignment of system alarms to ring and display on stations that have an Alarm key assigned. The Alarm key is assigned in MMC 722(Station Key Pro- gramming). Alarm key programming is tenant wide(ten[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-339 (continued) No Code Alarm Name Definition - MJB-- LC P /T A SK Er r or LCP or T A SK Fault 08 MJB01 HD L C C o m E r r o r Communications to LCP lost or faulty . 09 MJB02 Me m o r y Al a r m 1 A RAM diagnostic check error has occurred in the MCP2. 10 MJB03 Me m o r[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-340 Samsung Business Communications (continued) No Code Alarm Name Definition - MJD-- DTRK Error ISDN or E1 ca rd Fault 33 MJD01 Sync Failure Clocking on TEPRI cards has become async hronous. 34 MJD02 Sync Recovery Clocki ng on TEPRI cards has become s ynchronous. 35 MJD03 Red Alarm L[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-341 (continued) No Code Alarm Name Definition - MJD-- DTRK Error ISDN or E1 ca rd Fault 50 MJD18 E1 Restart T he E1 card has restarted. Alarm Data = Cabinet, Slot(Cx-Syy) 51 MJD19 PRI Restart The PRI card has restarted. Alarm Data = Cabinet, Slot(Cx-Syy) 52 MJD20 BRI R[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-342 Samsung Business Communications (continued) No Code Alarm Name Definition MNF-- Minor Error Minor Faul t with A larm Buffer saving 64 M NF 01 C ard O ut A circuit card mounted in a universal slot has been re- moved from service o r is not re cognized by the system. Alarm Data = Ca[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-343 (continued) No Code Alarm Name Definition 80 MNF17 PSU Alarm Rec Over-configuration of c abinet has been corrected. Alarm Data = Cabinet, Slot(Cx-Syy) 81 MNF18 SLI Fault An SLI card has been detect ed as out of service via an internal CODEC test. Alarm Data = Cabin[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-344 Samsung Business Communications DEFAULT DATA ALL OFF A C T I O N D I S P L A Y 1) Press T ransfer button and enter 852. Display shows: 01:MJA01 ACT:OFF POR Restart 2) Enter desired Alarm Display number .(e.g., 64) OR 64:MNF01 ACT:OFF Card Out Press V olu me buttons to select desir[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-345 [853] MAINTENANCE BUSY This MMC is used to place stations, trunks and common resources equipment in a mainte- nance busy condition. Thi s can be used to isol ate suspected intermittent problems. S tations placed in maintenance busy will behave like a station in DND[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-346 Samsung Business Communications A C T I O N D I S P L A Y 1) Press T ransfer button and enter 853. Display shows busy functions: MAINTENANCE BUSY TRK :NONE Æ 2) Enter busy function type(0-8) via dial keypad. OR MAINTENANCE BUSY STN :NONE Æ Press V olume button to make selection [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-347 [854] DIAGNOSTIC TIME Provides a means to set the Diagnostic T ime. The system diagnostics tests include memory audits, internal loopback tests on digital trunks, and DSP , AA DSP tests. Additional tests include CODEC tests on analogue trunk and sta tion cards and [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-348 Samsung Business Communications [856] TECH PROGRAMMING LOGS This MMC lists the date, time and entry location of the last eight times that technician- level programming was accessed. This allows a technician to determine if there was unau- thorized access to system programming and [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-349 [857] VIRTUAL CABINET SET This MMC is the program that specifies the type of virtual cabinet card. The type of virtual cabinet card is as follows: Ty p e Range Ty p e Range SL T C2S01 ~ C2S03 BRI S T N C4S02 ~ C5S01 DGP C2S0 1 ~ C2S03 GCONF STN C4S02 ~ C5S01 WIRED [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-350 Samsung Business Communications 3) Press V olume botton to scroll card type and Select card type by pressing Right soft botton. C4-S01:SL T D GP 4) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. RELATED ITEMS MMC 724 NUMBER PLAB MMC 822 VI[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-351 [859] HARDWARE VERSION DISPLAY This MMC is used for system hardware EPLD/PCB version display . This is a READ- ONL Y MMC. No Option Description 1 MP CARD Shows the EPLD/PCB version of MCP . 2 C1S1 Shows the EPLD/PCB version of card in ca binet1/slot1. 3 C1S2 Shows [...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-352 Samsung Business Communications [861] SYSTEM OPTIONS Sets a number of system options. DEFAULT DATA AUTO UPDA TE TIME: DISABLE SYSTEM SPEED BIN: MAX 500 IDLE WHEN ENBLOC: DISABLE 2 LINE ENBLOCK: DISABLE 2 ZONE EXT P AGE: DISABLE USE LB FOR P AGE: NONE LP TRK T ONE DISC: DISABLE ISD[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-353 A C T I O N D I S P L A Y 1) Press T ransfer button and e nter 861. Display shows: A UTO UPDATE TIME DISABLE 2) Enter the option number . OR AUTO UPDATE TIME D ISABLE Press V olume button to select and press Right Soft button to move cursor .[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-354 Samsung Business Communications 3) Enter 1 or 0 to enable or disable. OR A UTO UPDATE TIME ENABLE Press V olume button to select and press Right Soft button to store. 4) Press T ransfer button to save and exit. OR Press Speaker button to advance to next MMC. RELATED ITEMS MMC 107 [...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications 2-355 [863] NODE INFO This MMC allows 1000 systems to be connected by u spnet service. No Option Description 1 ACCESS NUM Set s the system node ID 2 IP ADDR Sets the system IP address 3 TEL NUMBER Sets the system CO tel number 4 MAX COUNT Sets this value to support ENBLO[...]

CHAPTER 2. Ошибка ! Стиль не определен . 2-356 Samsung Business Communications [890] INITIALIZE PORT This MMC clears a call process or initializes the database for specif ic station or trunks. This will return the port to default condition. DEFAULT DATA NONE A C T I O N D I S P L A Y 1) Press T ransfer button and enter 890. Di[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications I ABBREVIA TION A AAA Authentication, Author ization and Accounting AC Alternating Current ACD Automatic Call Distribution ALG Application Level Gateway AME Ans wering Machine Emulation AMI Alternate Mark Inversion AOM Add On Module AP Access Point B BGM Background Music[...]

Ошибка ! Стиль не определен . II Samsung Business Communications D DASL Digital Ada pter Subscriber Loops DID Direct Inward Dialling DECT Digit al Enhanced Cordless T elecommu nications DGP Digital Phone DHCP Dynamic Host Conf iguration Protocol DLI Digital Line Interface DND Do Not Disturb DPIM Door Phone Interface Module DSP[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications III IP Internet Protocol IPC Inter-Processor Communication IPDC Internet Protocol Device Control IPM Inter-Processor Communica tions and Memory Module IP-SCP Internet Protocol Service Control Point ISDN Integrated Services Digital Network ISUP ISDN User Par t ITM IP T el[...]

Ошибка ! Стиль не определен . IV Samsung Business Communications O OPX Off Premises Extension P P A T Port Address T ranslation PBA Printed(circuit) Board Assembly PCB Printed Circuit Board PCM Pulse Code M odulation PCMMC PC-based Man Machine Communication PLL Phase Locking Loop POP3 Post Office Protocol version 3 PPP Point t[...]

OfficeServ 7100 Call Server Programming Guid e Samsung Business Communications V SLI Single Line Interface SL T Single Line T eleph one SMDR S tation Message Detail Recording SMTP Simple Mail T ransfer Protocol SoL Server optimized Linux ST A S panning Tree Algorithm STP Signalling T ransfer Point SVMi Samsung V oice Mail(integrated) T T API T elep[...]

Ошибка ! Стиль не определен . VI Samsung Business Communications W W AN Wide Area Network WBS Wireless Base S tation WIM W AN Interface Module WLI Wireless LAN I nterface X xDSL x-D igital Subscriber Line[...]

Of ficeSer v 7100 Call Ser ver Prog ra mming Guide ©2007 Samsung Electronics Co., Ltd. All rights reserved. Information in this giude is proprietary to SAMSUNG Electronics Co., Ltd. No information contained here may be copied, translated, tran- scribed or duplicated by any form without the prior written con- sent of SAMSUNG . Information in this g[...]