Samsung 650FP инструкция обслуживания

ii LCD MONITOR quick start guide 650MP , 650FP[...]

Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by holding the groov[...]

LCD Display Manuals Quick Setup Guide Warranty Card (Not available in all loca- tions) User's Guide Cables Power Cord D-Sub Cable Others Remote Control (BP59-00138A) Batteries (AAA X 2) (Not available in all loca- tions) BNC to RCA Adaptor Jack Ferrite Core for Power Cord Sold separately DVI Cable Network Box Wall Mount KIT Introduction 9[...]

Sold separately RGB to BNC Cable BNC to BNC Cable Semi Stand KIT Ferrite Core • The ferrite cores are used to shield the cables from interfer- ence. • When connecting a cable, open the ferrite core and clip it around the cable near the plug. Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to [...]

Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [ PC ] → [ DVI ] → [ AV ] → [ Component ] → [ HDMI ] → [ MagicInfo ] → [ BNC ] Note • MagicInfo can only be enabled when a network box is connected. • The HDMI port and network box cannot be connected at the same time. PIP button P[...]

POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB IN (PC Connection Terminal (In- put)) • Use a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) • Connect the RGB IN port on the mon[...]

DVI/RGB/HDMI AUDIO IN (PC/DVI/ HDMI Audio Connection Terminal (Input)) AV/COMPONENT AUDIO IN [R-AUDIO- L] Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the LCD Display. DVI OUT • Connect a monitor to another monitor through a DVI cable. • Connect the [DVI OUT] port on the mon- itor to the [HDMI IN] port on [...]

BNC OUT [R, G, B, H, V] (BNC Terminal (Output)) BNC (Analog PC) Connection: connecting the R, G, B, H, V ports. The number of LCD Displays that can be connected to the loopout depends on the ca- bles, signal source, etc. With cables or signal source where there is no degradation, up to 10 LCD Displays can be connected (May not be supported dependin[...]

POWER OFF Number Buttons DEL / GUIDE button + VOL - SOURCE D.MENU TOOLS Up-Down Left-Right buttons INFO COLOR BUTTONS TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P TV MENU RETURN EXIT MagicInfo 1. POWER Turns the product On. 2. OFF Turns the product Off. 3. Number Buttons Press to change the channel. 4. DEL / GUIDE but- ton The "-" button is us[...]

- This function does not work for this LCD Display. 9. Up-Down Left-Right but- tons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 10. INFO Current picture information is displayed on the upper left corner of the screen. 11. COLOR BUTTONS Press to add or delete channels and to store channels to the fav[...]

19. RETURN Returns to the previous menu. 20. EXIT Exits from the menu screen. 21. MagicInfo MagicInfo Quick Launch Button. Note MagicInfo can only be enabled when a network box is con- nected. Introduction 17[...]

Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector [...]

Using the HDMI (digital) output on the graphics card. • Connect the [HDMI IN] port on the LCD Display to the HDMI port on the PC using the HDMI cable. Note When the HDMI cable to the PC, ensure that you select HDMI from both the Source List and Edit Name before selecting PC or DVI device so that normal PC screen and sound can be outputted. Note t[...]

Connect the audio cable for your LCD Display to the audio port on the back of the LCD Display. Connect the power cord for your LCD Display to the power port on the back of the LCD Display. Turn on the power switch. Note • Turn on both your computer and the LCD Display. • Contact a local SAMSUNG Electronics Service Center to buy optional items. [...]

Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display . 2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder [...]

2. Select BNC for the Camcorder connection using the SOURCE button on the front of the LCD Display or on the remote control. Connecting Using a DVI Cable 1. Connect between the [DVI OUT] port on the LCD Display and the input port on another monitor using a DVI cable. 2. Connect between the [AUDIO OUT] port on the LCD Display and the audio input por[...]

Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI to HDMI Cable 1. Connect the DVI output terminal of a digital output device to the [HDMI IN] terminal of the LCD Display using a DVI to HDMI cable. 2. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digi[...]

2. Connect a Component cable between the [BNC/COMPONENT IN [R/Y, G/P B , B/P R ]] port on the LCD Display and the P R , Y, P B jacks on the DVD player. Note • Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control. • Then, start the DVD Player with a DVD disc inserted[...]

Connecting to an Audio System 1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and [AUDIO OUT] on LCD Display. Connections 30[...]

Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display. The f[...]

• Do not use benzene, thinner or other flammable sub- stances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user is responsible for any damage caused by using these substances. Symptoms and Rec[...]

A: Check if the signal cable between the computer and the LCD Display is securely con- nected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and th[...]

Q: The screen color is inconsistent. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The Power Indicator blinks. A: The LCD Display [...]

A: Check if the batteries are empty. A: Check if the power is on. A: Check if the power cord is securely connected. A: Check if a special fluorescent or neon lamp is on in the vicinity. Q & A Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card. Note That video card support can vary, depending on th[...]

Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the In- formation section or contact your dealer. Troubleshooting 88[...]