Ryobi OSS500 инструкция обслуживания

Y our new oscillating spindle sander has been engineered and manufactured to Ryobi's high standard for dependability , ease of operation, and operator safety . Properly cared for , it will give you years of rugged, trouble-free performance. W ARNING: To reduce the risk of injury , the user must read and understand the operator ’s manual. Tha[...]

2 INTRODUCTION ■ Introduction ........................................................................................................................................................ 2 ■ Rules for Safe Operation ....................................................................................................... ......................... 3-5 [...]

3 RULES FOR SAFE OPERA TION Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your tool works. READ ALL INSTRUCTIONS ■ KNOW YOUR POWER TOOL. Read the operator's manual carefully. Learn [...]

4 RULES FOR SAFE OPERA TION ■ DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by a qualified service technician at an authorized service center. ■ KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petro- leum-based products, or an[...]

5 RULES FOR SAFE OPERA TION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper acciden[...]

6 SPECIFICA TIONS Oscillating Range 5/8 in. (15.9 mm) Oscillations Per Minute 58 OPM Spindle Size 1/2 in. (12.7 mm) No Load Speed 2000 RPM Input 120 Volts, 60 Hz, AC only, 3.5 Amps Weight 49 lbs. (22.2 kg) UNP ACKING INFORMATION We have shipped the oscillating spindle sander completely assembled and ready to use with a 1 in. (25.4 mm) rubber spindl[...]

7 Before using the oscillating spindle sander, familiarize yourself with all operating features and safety requirements. However, do not let familiarity with the tool make you careless. W ARNING: Exercise caution when using the oscillating spindle sander. Careless actions, for even a fraction of a second, can result in serious personal injury. SWIT[...]

8 FEA TURES Fig. 1 W ARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. SPINDLE HEX NUT SANDING SLEEVE (1 in. (25.4 mm)) THROAT PLATE TABLE TOP THROAT PLATE STORAG[...]

9 ADJUSTMENTS W ARNING: The sander should never be connected to a power supply when you are assembling parts, making ad- justments, cleaning, or when not in use. Disconnect- ing the tool will prevent accidental starting that could cause serious personal injury. SELECTING SANDING SLEEVES Selecting the correct size diameter, correct size grit, and co[...]

10 ADJUSTMENTS REMOVING SANDING SLEEVES See Figure 3. Follow these directions to remove sanding sleeves. ■ Unplug the sander. W ARNING: Failure to unplug the tool could result in accidental starting causing serious injury. ■ Grasp and hold the sanding sleeve on the spindle. ■ Loosen the hex nut using the wrench provided. NOTE: If the hex nut [...]

11 ADJUSTMENTS Fig. 5 THROAT PLATE HEX NUT UPPER SPINDLE WASHER SANDING SLEEVE SPINDLE WRENCH LOWER SPINDLE WASHER INSTALLING 1/2 INCH (12.7 mm) SANDING SLEEVES See Figure 5. Follow these directions to install 1/2 inch (12.7 mm) sanding sleeves. ■ Unplug the sander. W ARNING: Failure to unplug the tool could result in accidental starting causing [...]

12 OPERA TION W ARNING: Always wear safety goggles or safety glasses with side shields when operating this tool. Failure to do so could result in dust, shavings, or loose particles being thrown into your eyes, resulting in possible serious injury. MOUNTING THE SANDER TO A WORK SURFACE See Figures 6 and 7. Follow these directions to mount the sander[...]

13 OPERA TION OPERATING THE SANDER See Figures 8 and 9. Follow these directions to operate the sander. ■ Insert the switch key. ■ Turn on the sander by lifting the switch. ■ Let the motor build to its full speed. ■ Feed the workpiece gradually against the sanding sleeve from right to left. W ARNING: Do not let the workpiece contact the sand[...]

14 W ARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. GENERAL Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carb[...]

15 NOTES[...]

OPERA T OR'S MANUAL Oscillating Spindle Sander OSS500 - Double Insulated R YOBI TECHNOLOGIES INC. 1428 Pearman Dairy Road Anderson, SC 29625 Post Office Box 1207 Anderson, SC 29622 www .ryobitools.com Phone 1-800-525-2579 983000-146 9-02 • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, s[...]