Renesas TFP-144 инструкция обслуживания

H8S/2169 Series TFP-144 User System Interface Cable (HS2169ECN61H) for E6000 Emulator User’s Manual HS2169ECN61HE(B)[...]

Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property[...]

i Preface Thank you for purchasing this user system interface cable (HS2169ECN61H) for the Renesas’s original mi crocomputer H8S/2169 series. The HS2169ECN61H is a user system interface cable that connects an H8S/2148 series E6000 emulator (HS2148EPI61H; hereinafter referred to as the emul ator) to the IC socket for a TFP-144 package and expansio[...]

ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interf ace Cable to Expansion I/O board ................................... 3 2.2 Connecting Us[...]

Section 1 Configuration CAUTION Use an NQPACK144SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-144 package IC socket on the user system. Figure 1 shows the configuration of the HS2169E CN61H user system interface cable for the TFP-144 package. Figure 1 HS2169ECN61H User System Interface Cable 1[...]

2 Table 1 lists t he HS2169ECN61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2169ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the TFP-144 package 4 Socket cover 1 For installing an TFP-144 packaged MCU 5 Screws (M2.0 x 10 mm) 4 For fastenin[...]

Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Expansion I/O board W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user syste[...]

Emulator station Expansion I/O board E6000 Cable body connector User system interface cable USER I N TER FA C E CAB L E6 0 0 0 E M UL A T O E6000 Figure 2 Connecting User System Int erface Cable to Expansion I/O Board 4[...]

2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the [...]

Use the guide pins provided to determ ine where to install t he IC socket, as shown in figure 3. User system IC socket (NQPACK100SE manufactured by Tokyo Eletech Corporation) Guide pins 4 projections to apply epoxy resin adhesive to Bottom view of IC socket Pin 1 Figure 3 Location Setting of IC Socket 2.2.2 Soldering IC Socket After fastening, sold[...]

7 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an TFP-144 package on t he user system wit h pin 1 on the user system interface cable head, and inse rt the user system interface cable head into the IC socket on the user system, as shown i n figure 4. 2.2.4 Fastening Cable Head CAUT[...]

Fasten the user system interface cable head to the IC socket fo r an TFP-144 package on the user system wit h the four screws (M2.0 x 10 m m) provided. Each screw should be tightened a little at a time, alternating between screws on opposi ng corners. Take special care, such as manually securing the IC socket soldered area, to prevent the soldered [...]

2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Unfastening jig Push the unfastening jig Removing User system Figure 5 Fastening Cable Body 9[...]

2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an TFP-144 package (NQPACK144SE: m anufactured by Tokyo Eletech Corporation). Not e that the dimensions in figure 6 are somewhat different from those of t he actual chip's m o[...]

2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 7. Figure 7 Dimensions for User System Interface Cable Head 11[...]

2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 8. Figure 8 Resulting Dimensions after Connecting User System Interface Cable 12[...]

13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a screwdriver w hose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantl[...]

Figure 9 Installing MCU to User System 14[...]

Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2148 series, turn on the emulator according to the procedures described in the H8S Series E6000 Em ulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connec tions by accessing the exte rnal m emory and ports to check the bus states of the pi[...]

Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU. 3. To avoid breaking wires in the cable body, d[...]