Renesas REG10J0020-0200 инструкция обслуживания

REG10J0020-0200 Renesas Starter Kit LCD Application Board User's Manual RENESAS ST ARTER KIT Rev .2.00 Renesas T echnology Europe Ltd. Revision date ： 29. 1 1.2007 www .renesas.com[...]

T able of Content s Chapter 1. Preface .................................................................................................................................................. 3 Chapter 2. Purpose ............................................................................................................................... ...............[...]

Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this document, either in w hole or part is prohibited without the written permission of Rene sas Technology Europe Limited. Trademarks All brand or product names used in this manual are trademarks or registere[...]

Chapter 2.Purpose This RSK Application Board is an evaluation tool for Renesas microcontrollers with an LCD driver interface. It is used in con ju nction with the RSK for the microcontroller to be evaluated. Features include: • Mounting connections to allow RSK to be added to top of board. • Interface to standard RSK LCD expansion connector and[...]

Chapter 3.Board Layout 3.1.Component References The following diagram shows the component references for the board. Figure 3-1: Component Refer ences 5[...]

3.2.Board Component functions The following diagram the shows the functions of the components on the board. JA 5 JA 1 JA 6 JA 2 Appl ic at ion Boar d Int erfac e Appl ic at ion Boar d Int erfac e JA 4 LCD Sw it c h Co i n Ce l l H o l d er LC D A ppl ic at ion Int e r fac e Figure 3-2: Board Layout Caution: If processor is not in low power mode at [...]

3.3.Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connect ors are on a common 0.1” grid for easy interfacing. LCD connector 170.00m m 100.00mm Coin Cell Holder 115.00m m 14.00mm 86.36mm 85.00mm 80.01mm 50.80 m m 27.00m m 45.00m m Corners x4 3mm radius JA1 JA2 JA4 JA6 JA5 LCD ON OFF 5.0[...]

Chapter 4.User Circuitry 4.1.Fitting the Target RSK to the RSK LCD application board The board is supplied with 2x 24 way sockets, 2x 26 way sockets and 1 x 50 way socket. These should be soldered on the underside of the host RSK in JA1, JA2, JA5, JA6 and JA4 positions. The RSK should be plugged into the equivalent connectors on the RSK LCD applica[...]

Se g ment L K J I DP C B A DEFXMNGH Bit number 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Hex value for RAM A 0 1 0 0 0 1 1 1 0 1 1 0 0 0 1 0 4762 B 1 0 1 0 0 0 0 1 1 1 1 0 0 0 1 0 A 1E2 C 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 01E0 D 0 0 0 0 0 0 0 0 0 1 1 0 0 1 0 1 0065 E 0 1 0 0 0 0 0 1 1 1 1 0 0 0 1 0 41E2 F 0 1 0 0 0 0 0 1 0 1 1 0 0 0 1 0 4162 G 1 0 0 0 0 0 0 1 [...]

4.3.Coin Cell and switch. The board includes a coin cell holder to hold a 2032 3.6V coin cell. T o power the attached RSK from this cell the switch must b e in the “ON” position. IT IS IMPORT ANT NOT T O POWER THE A TT ACHED RSK VIA THE POWER SUPPL Y JACK OR VIA THE E8A IF THIS OPTION IS USED. Caution: If processor is not in low power mode at s[...]

Chapter 5.Headers 5.1.Application Headers This information is supplied for reference. Only JA1 pin 3 ( battery s upply voltage to RSK) and the ground pins are connected on this board. T able 5-1 and below T able 5-2 show the standard application header connections. JA1 Pin Generic Header Name CPU board Signal Name Pin Header Name CPU board Signal N[...]

JA2 Pin Generic Header Name CPU board Signal Name Pin Header Name CPU board Signal Name 1 Open drain RESn 2 External Clock Input EXTAL 3 Open drain NMIn 4 Regulated Supply 1 Vss1 5 Open drain output WDT_OVF 6 Serial Port SCIaTX 7 Open drain WUP IRQ0 8 Serial Port SCIaRX 9 Open drain IRQ1 10 Serial Port SCIaCK 11 Up/down MO_UD 12 Serial Port Handsha[...]

JA6 Pin Generic Header Name CPU board Signal Name Pin Header Name CPU board Signal Name 1 DMA DREQ 2 DMA DACK 3 DMA TEND 4 Standby (Open drain) STBYn 5 Host Serial SCIdTX RS232TX 6 Host Serial SCIdRX RS232RX 7 Serial Port SCIbRX 8 Serial Port SCIbTX 9 Serial Port Synchronous SCIcTX 10 Serial Port SCIbCK 11 Serial Port Synchronous SCIcCK 12 Serial P[...]

T able 5-5 below shows the LCD header connection s JA4 Pin Generic Header Name Signal Name Pin Header Name Signal Name 1 V0 V0 2 V1 V1 3 V2 V2 4 V3 V3 5 GROUND GROUND 6 GROUND GROUND 7 COM1 COM1 8 COM2 COM2 9 COM3 COM3 10 COM4 COM4 11 SEG1 SEG1 12 SEG2 SEG2 13 SEG3 SEG3 14 SEG4 SEG4 15 SEG5 SEG5 16 SEG6 SEG6 17 SEG7 SEG7 18 SEG8 SEG8 19 SEG9 SEG9 2[...]

Chapter 6.Code Development RSKs with appropriate LCD connections will include suitable sam ple software to drive the LCD on this board. Section 4.2 includes details of bit mapping for the LCD segments. 15[...]

Chapter 7.Additional Information For details on how to use High-performance Embedded Workshop (HEW), refer to the HEW man ual available on the CD or from the web site. Online technical support and information is available at: http://www.renesas.com/renesas_starter_kits T echnical Contact Details America: techsupport.rta@renesas.com Europe: tools.su[...]

Renesas S tarter Kit LCD Application Board User's Ma nual Publication Date Rev.2.00 29.11.2007 Published by: Renesas T echnology Europe Ltd. Duke’s Meadow , Millboard Road, Bourne End Buckinghamshire SL8 5F H, United King dom ©2007 Renesas T ec hnology Euro pe and Renes as Solutions C orp., All Ri ghts Reserved.[...]

Renesas S tarter LCD Application Board User's Manual Renesas T echnology Europe Ltd. Duke’s Meadow , Millboard Road, Bourne End Buckinghamshire SL8 5F H, United King dom[...]