Renesas HS2655ECH61H инструкция обслуживания

2004.1.29 H8S/2655 Group QFP-128 User System Interface Cable HS2655ECH61H User’s Manual Renesas Microcom puter Development Envi ronment System Rev.4.00[...]

Cautions Keep safety firs t in your circuit des igns! 1. Renesas Technology Corp. puts the maximum effort into making s emiconductor products better and more reliable, but there is always the poss ibility that trouble may occur with them. Trouble with se miconductors may lead to pers onal injury, fire or property damage. Remember to give due cons i[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attemp t to use the user system interface cable until you fully understand its mec h an is m. User Syst em Interf ace Ca ble: Thro ugho ut this d oc u ment, the t er m [...]

II LIMITED WARRANTY Renesas warrants its user s y stem interfa ce cabl es to be manufactured in accordance with published specifications and free from d efects in mater ial and/or workmanship. Renesas will re pair or replace a n y user sy stem interface cables deter mined to be defective in mate rial and/or workmanship. User s ystem interface cable[...]

III State Law : Some states do not allo w the exclusion or li mitation of imp lied warranties or liability for incidental or consequential da mages, so the above limitatio n or exclusion may not apply to you. Thi s warr an t y give s yo u spec i fic le gal ri ght s, and you ma y ha ve ot her rig hts wh ic h ma y var y fro m state to state. The Warr[...]

IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attemp t to use the user system interface cable until you fully understand its mec h an is m. DEFINITION OF SI GNAL WORDS This is the safety alert sy mbol. It is u sed to al ert[...]

V W ARNING Observe the pr ecautions listed b elow. Failure to do so will result in a FIRE H AZARD and will damage the user system and the emul ator product or will r esult in PERSONAL INJURY. The USER PROGRA M will be LOST. 1. Do not repair or remodel the emul ator product by yourself for elect ric shock pre vention and quality assurance. 2. Always[...]

i Preface Thank y ou for purch asing this us er sys tem in terface cable (HS2655ECH61H) f or the Renes as’s origin al m icrocom puter H8S/ 2655 group. The HS2655ECH61H is a u ser sy stem interface cable th at connects an H8S/2655 group E6000 emu lator (HS2655EPI61H; hereinaf ter referred t o as the em ulator) t o the IC sock et for a QFP- 128 pac[...]

ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 4 2.1 Connecting User Sy stem In terface Cable to Em ulator Station .......................................... 4 2.2 Connect[...]

1 Section 1 Configuration CAUTION Use an NQPACK 128RD socket (manuf actured by Tokyo Eletech Corporation) for the FP-128 package IC socket on the user syst em. Figure 1 s how s the conf iguration of the HS2655ECH 61H user sy stem interface cable f or the FP-128 packag e.[...]

2 Figure 1 HS2655EC H61H User System In terface Cable[...]

3 Table 1 li s ts t h e HS 2655EC H61H com ponen t s. Pl eas e m ake su re you h ave all of t h es e com ponen ts when unpacking. Table 1 HS2655ECH61H Com p onents No. Component Quantity Remar ks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the FP-128 package 4 Socket cover 1 For installing anFP-128 packaged M CU 5 Screws (M 2 x 10 mm[...]

4 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user syst em[...]

5 Figure 2 Connecting User System Interface Cable to Em ulator Station[...]

6 2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part . Before connecting, make sure that pin 1 on bot h sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage[...]

7 User system Bottom view of IC socket 4 projections to apply epoxy adhesice to IC socket (Tokyo Eletech Corporation NQPACK128RD) Guide pins Pin 1 Figure 3 Location Setting of IC Sock et 2.2.2 Soldering I C Socket Af ter fasten ing, s older the IC sock et for an FP-128 pack age to the user syst em. Be sure to completely solder the leads so that the[...]

8 2.2.4 Fas tening Cab le Head CAUTION 1. Use the screwdriber provided for t ightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the f orce required to turn th e screw becomes significantly greater th an that needed when first tightening. If a screw is tig[...]

9 Figure 4 Connecting User System Interface Cable to User Sys tem[...]

10 2.2.5 Fas tening Cab le Body Connect the cable body to the cable h ead. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 5 Fastening Cable Body[...]

11 2.3 Recomm ended Dimensions for User System Mount Pad Figure 6 sh ow s th e recom m en ded dim ension s f or th e m ount pad (footprint) for the user sys tem with an IC sock et for an F P-128 package (NQPA CK128RD: m anu factu red by Toky o Eletech Corporation). Note that th e dimens ions in f igure 6 are som ew hat diff erent from those of the [...]

12 2.4 Dimensions for User System Interface Cable Head The dimen sions for th e user sy stem interface cable h ead are show n in f igure 7. Figure 7 Dim ensions for User System Interface Cable Head[...]

13 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dim ens ions, after con necting th e user sy stem interface cable head to th e user sy stem , are show n in figu re 8. Figure 8 Resulting Dim ensions after Connecting User Sys tem I nterface Cable[...]

14 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for t ightening screws. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the f orce required to turn th e screw becomes significant[...]

15 User system Screws (M2 x 6 mm) IC socket Tokyo Eletech Corporation NQPACK128RD Socket cover MCU Pin 1 Figure 9 Installing M CU to User System[...]

16 Section 4 Verifying Oper ation 1. When u sing th e E6000 emu lator for the H8S/ 2655 group, turn on the em ulator accordin g to the procedures des cribed in th e H8S Fam ily E6000 Em ulator Us er's Man ual (HS 2000EPI61HE). 2. Verify the user sy stem in terface cable connections by accessing the external m emory and ports to check the bu s [...]

17 Section 5 Notice 1. Make s ure that pin 1 on the user sy stem IC socket is correctly aligned w ith pin 1 on the cable head before insertin g the cable head in to the user sy stem IC socket. 2. The dimen s ion s of the recom m ended m oun t pad f or th e u s er sy stem IC s ocket are dif ferent f rom those of the MCU. 3. This user sy stem interf [...]

18 6. The JP1 j um per socket is used f or testing. Do n ot remove th e inserted jum per pin. JP1 Figure 12 JP1 Jump er Socket[...]

H8S/2655 Group QFP-128 User System Interface Cable HS2655ECH61H User's Manual Publication Date: Rev.4.00, January 29, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd.  2004 Renesas Technology Corp. All rights rese[...]

H8S/26 55 Gr oup Q FP-128 User Sy stem Inte rface C able HS2655E C H61H U ser’ s Manual REJ10B0086-0400H[...]