Renesas H8SX/1653 инструкция обслуживания

H8SX/1653 Group E6000 H TFP-120 User System Interface Board HS1653ECN61 H User’s Manual Renesas Micro computer Develo pment Enviro nment Syst em HS1653ECN61 HE Revision Date: Dec. 09, 2005 Rev.2.00 REJ10B0200- 0200[...]

[...]

1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp[...]

[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not atte mpt to use the user syste m interfa ce board until yo u fully understand its mec ha ni s m. User Syst em Interf ace Board : Thro ughout t his d o cume nt , the t e[...]

II LIMITED WARRANTY Renesas warrants its user s ystem interface boar ds to be manufactured in accordance with published specific ations and free from defects in material and/or workmanship. Renesas will repair or replace any user system inter face boards determine d to be defective in mater ial and/or workmanship. Us er system interf ace boards are[...]

III State Law : Some states do not allo w the exclusion or li mitation of implied warran ties or liab ilit y for incidental or consequential da mages, so the above limitation o r exclusion may not apply to you. Thi s warr an t y give s yo u spec i fic le gal ri ght s, and you ma y ha ve ot her rig hts wh ic h ma y var y fro m state to state. The Wa[...]

IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not atte mpt to use the user syste m interfa ce board until yo u fully understand its mec ha ni s m. DEFINITION OF SI GNAL WORDS This is the safety ale rt symbo l. It is used t o al[...]

V W ARNING Observe the pr ecautions listed b elow. Failure t o do so will result in a FIRE H AZARD and will damage the us er system and the emul ator product or will r esult in PERSONAL INJURY. The USER PROGRA M will be LOST. 1. Do not repair or remodel the emul ator product by yourself for elect ric shock pre vention and quality assurance. 2. Alwa[...]

i Preface The HS1653ECN61H is a us er system interface board that connects a us er system for the H8SX/1653 TFP -120 package to the H8SX/ 1650 E6000H emulator (HS 1650EPH60H). Emulation of the H8SX/1653 group is only poss ible when this user sys tem interface board is connected to the HS1650EP H60H.[...]

ii Contents Section 1 Configuration ..................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interface B oard to User System ................................................ 3 2.1.1 Insta[...]

1 Section 1 Configuration Figure 1 and table 1 show the configuration and components of the us er system interface board for the TFP-120 package. Pleas e make sure you have all of thes e components when unpacking. Evaluation chip board Spacer User system interface board User system IC socket Screws (M2 × 12 mm) with flat washers (for fastening cab[...]

2 CAUTION Use an IC149-120- 043-B51 socket (m anufactured by YAMAICH I ELECTRONICS Co., Lt d.) for th e TFP-120 package IC socket on the user syst em. Table 1 HS1653ECN61H C omponents No. Component Quantity Remarks 1 User system interface board 1 2 IC socket 1 For the TFP-120 package (to be mounted on the user system) 3 Socket cover 1 For installin[...]

3 Section 2 Connection Procedures 2.1 Connecting User System Interface Board to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part . Before connecting, make sure that pin 1 on bot h sides are correctly aligned. Failure to do so will result [...]

4 To connect the cable head to the user system, follow the ins tructions below. 2.1.1 Installing IC So cket After checking the l ocation of pin 1 on the IC s ocket, apply epoxy resin adhes ive to the bott om of the IC socket for a TF P-120 package, and fasten it t o the user system before s oldering. 2.1.2 Soldering IC Socket After fastening, s old[...]

5 2.1.4 Fastening I C Socket Connector CAUTION 1. Use the screwdriver provided for t ightening screws. 2. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the f orce required to turn t he screw becomes significantly greater th an that needed when first tightening. If a scre[...]

6 User system interface board User system Pin 1 Screws (M2 × 12 mm) with flat washers (for fastening cable head) IC socket (IC149-120-043-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) Figure 2 Connecting User System Interface B oard to User System[...]

7 2.2 Exchanging th e Spacer of the Evaluation Ch ip Board While the user system interface board is connected to the user system, be careful not to apply load. Exchange the spacer (2.6MP × 10 mm) of the evaluation chip board with another spacer (2.6MP × 25 mm) provided for the user system interface board. Evaluation chip board Spacer (2.6MP × 25[...]

8 2.3 Connecting User System Interface Board to Evaluation Chip Board W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user syst em and the emulator product b[...]

9 Connector No. UCN1 UCN1 UCN2 UCN2 User system interface board Evaluation Chip Board Connector No. Board Connector No. Evaluation chip board Figure 4 Connecti ng User System Interface Board to Evaluation C hip Board[...]

10 2.4 Recommended Dimensions for User System Mount Pad (Footprint) Figure 5 shows the recommended dimensions for the mount pad (footprint ) for the user sys tem with an IC s ocket for a TFP-120 package (IC149-120-043-B 51: manufactured by YAMA ICHI ELECTRONICS Co., Ltd). Note that the dimensions in figure 5 are somewhat different from those of the[...]

11 2.5 Dimensions for Evaluation Chip Board and User System Interface Board The dimensions for the evaluation chip board and the user s ystem interface board are shown in figure 6. Unit: mm Tolerance: ± 0.5 mm 140.0 Evaluation chip board User system interface board 102.5 16.0 118.5 100.0 84.5 69.0 78.5 34.5 Figure 6 Dime nsions for E valuation Ch [...]

12 2.6 Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user s ystem interface board to the user sys tem, are shown in figure 7. Unit: mm Tolerance: ±1.0 mm 35.6 16.0 57.6 User system Evaluation chip board IC socket (IC149-120-043-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) 56[...]

13 2.7 Using the Emulator without Connecting User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part . Before connecting, make sure that pin 1 on bot h sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage th[...]

14 P1 SW1 ON USER OFF Figure 8 SW1 Jumper Socket Spacer (2.6MQ x 16 mm) Figure 9 Attaching Spacers[...]

15 Section 3 User System Interface Circuits The following user interface circuits are required for the emulator when the user s ystem interface board is in use. Sub-MCU MD control circuit Monitoring circuit LPT16244 MD_CLK Vcc 47 k Ω PM0-PM4 User system VBUS MD_CLK DrVss DrVss PM0-PM4 VBUS DrVcc DrVcc USD- USD- USD+ USD+ Power-supply circuit EPM7[...]

16 P23 P27 P23 P27 SN74CB3Q3306A SN74CB3Q3306A MCU User system Figure 11 User System Interface Circuit (2) MCU User system Sub-MCU P14 P14 SN74CB3Q3306A TXD SN74CB3Q3306A Figure 12 User System Interface Circuit (3)[...]

17 MCU VHC244 UHC14 _RES Vcc User system EPM7128 EPM7128 _RES 47 k Ω Figure 13 User System Interface Circuit (4)[...]

18 Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H Emulator User' s Manual (HS1650EPH 60HE). 2. Verify the user system interface cable connections by checking the pin st ates with the CHECK command (emulator command) and checking the bus states with the FILL command (emulator [...]

19  To use the crystal oscillator mounted on the evaluation chip board Install the cry stal o scillato r in to the crystal oscillator terminals on th e evaluation ch ip board. Evaluation chip board Crystal oscillator terminals Crystal oscillator Enlarged view X1 X2 Figure 15 Insta lling the Clock Oscillator[...]

20 Section 5 Notice 1. Before connecting any parts or cables, make sure that pin 1 on the both s ides are correctl y aligned. 2. Do not apply excessive force to the user system interface board while it is connected to the user sy stem. 3. The dimensions of the recommended mount pad for the IC socket for this user sys tem interface board are differe[...]

21 8. When this emulator is used without connecting to the user s ystem, ensure that t he SW1 jumper pin is inserted to [OFF]. Failure to do so will damage the emulator product, user s ystem interface cable, and user system. 9. To connect the emulator to the user system, ensure that the SW1 jumper pin is ins erted to [ON]. Failure to do so will dam[...]

22 Section 6 Restrictions There are the following res trictions on emulation of the H8S X/1653 group when the user s ystem interface board is connected to the emulator. 1. The USB clock frequency is fixed to 48 MHz regardl ess of the EXTA L input. 2. P14 cannot be used as a port if t he serial output function has already been s elected. The port pi[...]

Renesas Microcomputer Development Environment System User's Manual H8SX/1653 Group E6000H TFP-120 User System Interface Board HS1653ECN61H Publication Date: Rev.1.00, November 11, 2004 Rev.2.00, December 9, 2005 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communic[...]

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to " http://www.renesas.com/en/network " for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) [...]

2- 6 -2, Ote-machi, Chiyoda-ku, Tokyo, 100-0004, Japan H8SX/1653 Group E6000H TFP-120 User Syste m In terface Board HS1653ECN61H User’s Manual[...]