Renesas H8S/2646 Series инструкция обслуживания

H8S/2646 Series FP-144 User System Interface Cable (HS2646ECH61H) for E6000 Emulator User’s Manual HS2646ECH61HE(B)[...]

Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property[...]

i Preface Thank you for purchasing this user system interface cable (HS2646ECH61H) for the Renesas’s original mi crocomputer H8S/2646 series. The HS2646ECH61H is a user system interface cable that connects an H8S/2636 and H8S/2646 series E6000 em ulator (HS2646EPI61H; hereinafte r referred to as the emulator) t o the IC socket for a FP-144 packag[...]

ii Contents Section 1 Configuration ...................................................................................... 1 Section 2 Connection Procedures ....................................................................... 3 2.1 Connecting User System Interf ace Cable to Em ulat or Station ......................................... 3 2.2 Conne[...]

Section 1 Configuration CAUTION Use an NQPACK144SD socket (manufactured by Toky o Eletech Corporation) for the FP-144 package IC socket on the user system. Figure 1 shows the configuration of the HS2646E CH61H user system interface cable for the FP-144 package. Figure 1 HS2646ECH61H User System Interface Cable 1[...]

2 Table 1 lists t he HS2646ECH61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2646ECH61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the FP-144 package 4 Socket cover 1 For installing an FP-144 packaged MCU 5 Screws (M2 x 10 mm) 4 For fastening ca[...]

Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system a[...]

Emulator station E6000 Cable body connector User system interface cable Figure 2 Connecting User System Interf ace Cable to Emulator Station 4[...]

2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the [...]

IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) User system Guide pins 4 projections to apply epoxy resin adhesive to Bottom view of IC soket Pin 1 Figure 3 Location Setting of IC Socket 2. Solder the IC socket for a FP-144 package t o the user system. CAUTION Be sure to completely solder the leads so that the solder slops gently [...]

7 2.2.3 Fastening Cable Head CAUTION 1. Use a Philips-type screwdriver whose head matches the screw head. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a scre[...]

Fasten the user system interface cable head to the IC socket for an FP-144 package on the user system with the four screws (M2 x 10 m m) provided. Each screw should be tightened a little at a time, alternating between screws on opposi ng corners. Take special care, such as manually securing the IC socket soldered area, to prevent the soldered IC so[...]

2.2.4 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 5 Fastening Cable Body 9[...]

2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an FP-144 package (NQPACK144SD: m anufactured by Tokyo Eletech Corporation). Not e that the dimensions in figure 6 are somewhat different from those of t he actual chip's m ou[...]

2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 7. Figure 7 Dimensions for User System Interface Cable Head 11[...]

2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 8. Figure 8 Resulting Dimensions after Co nnecting User System Interface Cable 12[...]

13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes [...]

MCU Pin 1 IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) User system Screws (M2 x 6 mm) Socket cover Figure 9 Installing MCU to User System 14[...]

Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2646 series, turn on the emulator according to the procedures described in the E6000 Series Em ulator User's Ma nual (HS2000EPI61HE). 2. Verify the user system interface cable connec tions by accessing the exte rnal m emory and ports to check the bus states of the pins [...]

Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU. 3. This user system interface cable is specifi [...]