Renesas H8S/2615 Series инструкция обслуживания

HS2615ECH61HE H8S/2615 Series FP-80Q User System Interface Cable (HS2615ECH61H) for E6000 Emulator User’s Manual ADE-xxx-xxx Rev. 2.0 4/1/03 Renesas Technology Corp.[...]

[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interf ace cable un til you fully understand its mechanism. User System Interfa ce Cable: Throughout this document, the term "user s[...]

II LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or rep lace any user system interface cables determ in ed to be defective in material and/or workmanship. User system interface cables are wear[...]

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequent ial dam ages, so the above limit ation or exclusi on may not apply t o you. This warranty gives yo u specific l egal rights , and you m ay have other rights w hich may vary from state to state. The Warranty is Void in [...]

IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interf ace cable un til you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert y ou t[...]

V W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZA RD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The U SER PROGRAM will be LOST. 1. Do not repair or rem odel the emulator product by yourself for electric s hock prevention and quality assurance. 2. Always swit[...]

Cautions 1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, t rademark, or other inte llect ual propert y rights for inform ation contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property [...]

[...]

i Preface Thank you for purchasing this user system interface cable (HS2615ECH61H) for the Renesas’s original mi crocomputer H8S/2615 seri es. The HS2615ECH61H is a user system interface cable that connects an H8S/2615 series E6000 emulator (HS2612EPI61H; herei nafter referred to as the emul ator) to the IC socket for a FP-80Q package for the H8S[...]

ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interf ace Cable to Emulat or Station ......................................... 3 2.2 Connectin[...]

1 Section 1 Configuration CAUTION Use an IC149-080-017-B5 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-80Q package IC socket on the user system. Figure 1 shows the configuration of the HS2615E CH61H user system interface cable for the FP-80Q package. User system IC socket Cable head Screws (M2 x 12 mm) with flat washers (for f[...]

2 Table 1 lists t he HS2615ECH61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2615ECH61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the FP-80Q package 4 Socket cover 1 For installing an FP-80Q packaged MCU 5 Screws (M2 x 12 mm) 4 For fastening ca[...]

3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system[...]

4 Emulator station E6000 Cable body connector User system interface cable Figure 2 Connecting User System Int erface Cable to Emulator Station[...]

5 2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage th[...]

6 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-80Q package on the user system with pin 1 on the user system interface cable head, and insert the user system interface cable head into the IC socket on the user system, as shown in fi gure 3. 2.2.4 Fastening Cable Head CAUTION [...]

7 Fasten the user system interface cable head to the IC socket fo r an FP-80Q package on the user system with the four screws (M2 x 12 m m ; with four flat washers) provided. Each screw should be tightened a little at a time, alternating between scre ws on opposing corners. Take special care, such as manually securing the IC socket soldered area, t[...]

8 2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig User system Removing Figure 4 Fastening Cable Body[...]

9 2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an FP-80Q package (IC149-080-017-B5: m anufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 5 are somewh at different from those of the actual chip&[...]

10 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 6. Unit: mm Tolerance: ±0.5 mm 63.5 63.5 17.0 14.46 29.5 29.5 Figure 6 Dimensions for User System Interface Cable Head[...]

11 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 7. 9.4 21.5 Cable head User system Unit: mm Tolerance: ±0.5 mm IC socket (IC149-080-017-B5 manufactured by YAMAICHI ELECTRONICS Co. Ltd.) Figure 7 Resulti[...]

12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.0785 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes[...]

13 MCU Pin 1 IC socket (IC149-080-017-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Screws (M2 x 8 mm) with flat washers Socket cover Figure 8 Installing MCU to User System[...]

14 Section 4 Verifying Operation 1. Turn on the emulator according to the procedur es described in the H8 S Series E6000 Emulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connec tions by accessing the exte rnal mem ory and ports to check the bus states of the pins with the ME MOR Y_ FI LL c omma nd (e mul ato r [...]

15 Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correctly aligned wit h pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU. 3. This user system interface cable is specif[...]