Q-Logic 3000 инструкция обслуживания

59060-07 D Reference Guide Fibre Channel Event Message QLogic 3000/5000/9000 Seri es Fibre Channel Switch QLogic Intelligent Pass-thr u Module for IBM BladeCenter QLogic 20-Port SAN Switch Module for IBM BladeCenter QLogic V irtual Fabric Extens ion Module for IBM BladeCenter Firmware V ersion 7. x , 8. x , 9. x[...]

ii 59060-07 D Reference Guide Fibre Channel Event Me ssage QLogic 3000/500 0/900 0 Series Fibre Channel Switch Information fu rnished in this manual is believed to be accurate and reliab le. However , QLogic Corporation assumes no responsibility for its use, nor for any infringements of patent s or other right s of third part ies which may result f[...]

59060-07 D iii T able of Content s Preface Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Documentation Con ventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

iv 59060-07 D Reference Guide Fibre Channel Event Me ssage QLogic 3000/500 0/900 0 Series Fibre Channel Switch[...]

59060-07 D v Preface This manual describes the alarm messages for QLog ic Fibre Channel switches. This manual is organized as follows:  This preface describes the inte nded audience, related ma terials, and technical support.  Section 1 describes event logging concept s, including definitions of severity levels, how to configure the event log[...]

Preface Documentati on Conventions vi 59060-07 D  Te x t i n blue font indicates a hyperlink (jump) to a figure, t able, or section in this guide, and links to W eb sites are shown in underlined blue . For example:  T able 9-2 lists problems related to the user int erface and remote agent.  See “Installatio n Checklist” on page 3-6 . ?[...]

Preface T echnical Support 59060-07 D vii T echnical Support Customers should cont act their authorized maintenance provider for technical support of their QLogic product s. QLogic- direct customers may cont act QLogic T echnical Support; others will be redirected to their authorized mainte nance provider . Visit t he QLogic support Web site listed[...]

Preface T echnical Support viii 59060-07 D Knowledge Base The QLogic knowledge base is an extensive collection of QLogic product information that you can search for specific solutions. W e are constantly adding to the collection of information in our knowledge base to provide answers to your most urgent questions. Access the knowledge ba se from th[...]

59060-07 D 1-1 1 Event s and Event Logging Messages originate from the switch, from En terprise Fabric Suite, or from the QuickT ools web applet in response to e vent s tha t occur in the fabric. This chapter describes the following topics:  Understanding Severity Levels  Displaying Events using the Event Browser  Displaying the Events Usi[...]

1–Events and Eve nt Logging Displaying Events usi ng the Event Browser 1-2 59060-07 D Displaying Event s using the Event Browser Both Enterprise Fabric Suite and QuickT ools have an e vent browse r that displa ys a list of events generate d by the switches in the fabric and by the applications themselves. Event browser messages ar e permanently d[...]

1–Events and Eve nt Logging Displaying the Events Usin g the Command Line Interface 59060-07 D 1-3 In the CLI, each message has the followin g format: [ordinal][time_stamp][severity][source][message_ID][message_text] Here is a sample of an informative-level message from the Switch source : [1][Wed May 26 12:30:29.965 UTC 2004][I][8400.0022][Switc[...]

1–Events and Eve nt Logging Configuring the Event Log 1-4 59060-07 D Configuring the Event Log Y ou can customize what events are recorded in the switch e vent log using the Set Log command. With the Set Log comman d, you can filter the event s to be recorded by component, specific port s, and severity level. Y ou can choose from the following co[...]

1–Events and Eve nt Logging Configuring Port Alarm Thresholds 59060-07 D 1-5 Configuring Port Alarm Thresholds Y ou can configure the switch to generate alarms for selected events. Co nfiguring an alarm involves choosing an event type, rising and falling triggers, a sample window , and finally enabling or disabling the alarm. Y ou can configure p[...]

1–Events and Eve nt Logging Configuring Port Alarm Th resholds 1-6 59060-07 D[...]

59060-07 D 2-1 2 Event Messages This section lists even t messages from the command line interface and Enterprise Fabric Suite in message ID sequen ce by the following severity levels:  Fault Event s  Alarm Events  Critical Events  W arning Event s  Informative Events Y ou can look up a message by its messag e ID or by searching for [...]

2–Event Messages Fault Events 2-2 59060-07 D F AN1_MISSING Meaning: F AN1 is not installed. FW_APP_F AIL Meaning: Internal application failure. FW_APP_PEER_F AUL T Meaning: Application declared an e rror communicating with other CPU. FW_APP_SELF_F AUL T Meaning: Application declared an int ernal fault. FW_APP_ST ARTUP_F AIL Meaning: Application i[...]

2–Event Messages Fault Events 59060-07 D 2-3 HW_BAD_SEA TING Meaning: Blade is improperly seated. HW_MP_ACCESS_CPU0 Meaning: The maintenance p anel SPROM dat a accessed through CPU0 is either inaccessible or invalid. HW_MP_ACCESS_CPU1 Meaning: The maintenance p anel SPROM dat a accessed through CPU1 is either inaccessible or invalid. HW_MP_DA T A[...]

2–Event Messages Alarm Events 2-4 59060-07 D Alarm Event s An alarm event requires action before you can proceed any further . The following lists each alarm event ID numbers and message displayed, and provides a description of the meaning of the message and recommended a ction to take. (A1000.000F) (The switch is canceling the hotreset - try aga[...]

2–Event Messages Alarm Events 59060-07 D 2-5 (A1003.0010) (Segmenting, zoneset zone_ set_name not defined) Meaning: In non-interop mode, there is a co nflict in the zoning configuration, causing the Inter-Switch Link (ISL) to isola te. The zone set is not found within the local zoning dat a base while interop mode is disabled. Action: Contact you[...]

2–Event Messages Alarm Events 2-6 59060-07 D (A1003.0016) (Releasing Lock held too long by domain_ID ) Meaning: A zone merge could not be completed in the a cceptable time. Action: Check the status of th e switch given by doma in_ID . (A1003.0017) (Activation of zoneset by management server failed due to po rt port_number out of range.) Meaning: [...]

2–Event Messages Alarm Events 59060-07 D 2-7 (A1003.0021) (Failing remote zoning c onfiguration, Zoneset is empty) Meaning: An empty zone set was included a s part of a zo ne merge and was rejected. Action: Modify the zoning database o n the remote switch to remove or correct the empty zone set. (A1003.0022) (Unable to up date dat abase with newl[...]

2–Event Messages Alarm Events 2-8 59060-07 D (A1003.002A) (No response received from switc h with domain ID domain_ID ) Meaning: A S taged Fabric Configu ration (SFC) frame was sent to the switch given by domain_ID , but a response was not received. Action: Check the status of th e remote switch at the given domain ID. There could be an issue wit[...]

2–Event Messages Alarm Events 59060-07 D 2-9 (A1003.0031) (Error reading zoneset from a ctivate direct.) Meaning: A device supporting th e management server has sent an Activate Zoneset Direct $(AZSD) command that did not follow the expected standard layout. Action: Contact your autho rized maintenance provider . (A1003.0032) (Zoneset zone_se t_n[...]

2–Event Messages Alarm Events 2-10 59060-07 D (A1003.0038) (Merge failed, T otal zones in zoneset s limit would be exceeded.) Meaning: A fabric merge failed because the tot al number of zon es in zone sets exceeds the zoning data base limit. Action: Remove zones either from the local switch or the remote switch so that the combined sum is less th[...]

2–Event Messages Alarm Events 59060-07 D 2-1 1 (A1003.0040) (Zone Member type member_type unsupported.) Meaning: An invalid zone member type wa s discovered in a zone. ACL hard zone membership must be defined by domain_ID and port numb er . Action: Correct the member type. (A1003.0041) (Zoning object s which conta in Fibre Channel (FC) Address Me[...]

2–Event Messages Alarm Events 2-12 59060-07 D (A1003.004F) (No Zone Merge Response) Meaning: A merge request was sent ou t to all switches in the fabric but a response was not received from at least one switch. Action: Check other switches in fabric to determine why a response was not sent. (A1003.0050) (ISL group does not cont ain entry for this[...]

2–Event Messages Alarm Events 59060-07 D 2-13 (A1003.0058) (Active ZoneSet zon e_set no longer in dat abase, please deactivate zoneset if not already in progress or fabric will be inconsistent) Meaning: A zone set with the same name as th e current active zone set no longer resides in the zoning dat abase. The active zone se t will not be added t[...]

2–Event Messages Alarm Events 2-14 59060-07 D (A1003.0069) (Failing remote zoning c onfiguration, invalid zone dat a received) Meaning: Zoning activation failed because t he switch detected invalid zoning data that is not supported in the local interop mode. Action: Check your zoning configuration and remove incomp atible zone members. (A1004.000[...]

2–Event Messages Alarm Events 59060-07 D 2-15 (A1004.000C) (Eport Isolating due to Domain ID Locke d, Domain ID unavailable) Meaning: An E_Port isolated beca use the requested domain ID matches another in the fabric, and assigning an alte rnative is prohibited by the domain ID Lock pa rameter . Action: Disable the domain ID lock p arameter or rec[...]

2–Event Messages Alarm Events 2-16 59060-07 D (A1004.0013) (Eport Isolating due to all switches incap able of becoming Princip al Switch) Meaning: An E_Port isolated beca use the principal priority on all switches is set to 254. Action: Configure one of the switches to be the p rincipal switch by changing the principal priority . (A1004.0014) (Ep[...]

2–Event Messages Alarm Events 59060-07 D 2-17 (A1004.0026) (Configured Domain ID domain_ID not ava ilable and Domain ID is locked on this switch) Meaning: An attempt was made to connect a switch to a fabric with a conflicting domain ID, and the dom ain ID cou ld not be reassigned. Action: Change the domain ID so that it is unique in the fabric, o[...]

2–Event Messages Alarm Events 2-18 59060-07 D (A1004.0032) (E_Port not supported on remo te port. Reconfigure remote switch to connect.) Meaning: An E_Port isolated beca use the port on the remote switch could not configure it self as an E_Port. Action: Change the port type on the remote switch to G_Port or GL_Port. (A1004.0033) (Remote switch is[...]

2–Event Messages Alarm Events 59060-07 D 2-19 (A1004.0038) (W orldWide Name (WWN) de vice_WWN assigned domain domain_I D , fabric binding indicates this domain is rese rved for device_WWN .) Meaning: The user-activated fabric bindin g conflicts with the current domain ID assignment. Action: Change the domain ID of the device. (A1004.0039) (W orld[...]

2–Event Messages Alarm Events 2-20 59060-07 D (A1004.0049) (Eport Isolating due to Re mote inactive) Meaning: The remote switch is unrespo nsive, and the link has not been brought up. The port will be isolated beca use the remote switch failed to respond. Action: Investigate the remote switch for connection problems. (A1004.0050) (Maximum hard zo[...]

2–Event Messages Alarm Events 59060-07 D 2-21 (A1004.0056) (Blade compromised due to i nternal dat a link failure (SET)) Meaning: An I/O blade has been compro mised due to failure of its inte rnal data link to the CPU b lade. Action: Contact your autho rized maintenance provider . (A1004.0057) (Blade no longer compro mised due to internal dat a l[...]

2–Event Messages Alarm Events 2-22 59060-07 D (A1005.000E) (Configuration error , can't extend credit on loop cap able port s. Extended credit not granted for port: port_number ) Meaning: Loop port s cannot borrow credit s from the credit pool. Action: Change the port type to G_Port or F_Port. (A1005.0013) (Hot swap procedure failed - must h[...]

2–Event Messages Alarm Events 59060-07 D 2-23 (A1005.0039) (Fabric Login (FLOGI) from address FC_address failed) Meaning: The pa yload of the FLOGI was no t valid. Action: Check the device connection or repla ce the device. If the problem persists, cont act your authorized maintenance pro vider . (A1005.003A) (Fabric Login (FLOGI) from address FC[...]

2–Event Messages Alarm Events 2-24 59060-07 D (A1005.0042) (T arget device port_address att ached to port port_numb er with IOStreamGuard Enabled) Meaning: The ta rget device is attach ed to a port with IO S treamGuard enabled. Action: Disable I/O S treamGuard on the port. (A1005.0045) (Configured port dat a conflicting within hardware cap abilit[...]

2–Event Messages Alarm Events 59060-07 D 2-25 (A1005.004E) (Attempt s to login backend s witch fail because backend switch does n ot support NPIV .) Meaning: The backend fabric switch does not support N_Port ID Virtualizat ion (NPIV), which in turn brings down the TF_Port. Action: Ensure that the backend fabric switch support s NPIV . (A1005.004F[...]

2–Event Messages Alarm Events 2-26 59060-07 D (A1005.0055) (Canceling TFTP operati on as a result of a CPU switchover) Meaning: A CPU blade switchover occu rred while a T rivial File T ransfer Protocol (TFTP) operation was in progress. The operation was canceled. Action: Retry the operation. (A1005.0057) (Canceling the unp acking of a firmware im[...]

2–Event Messages Alarm Events 59060-07 D 2-27 (A1005.005E) (Canceling Services edit mode a s a result of a CPU switchover) Meaning: A CPU blade switchover occu rred while a services edit sessio n was in progress. The edit session was canceled . Action: Reopen the services edit se ssion. (A1005.005F) (Canceling Ni cknames edit mode as a result of [...]

2–Event Messages Alarm Events 2-28 59060-07 D (A1005.0066) (Switch is not fault -tolerant. Fault T olerant license is inst alled, but secondary CPU is faulted) Meaning: The QLogic 9000 switch is not fa ult tolerant because of a fault on the secondary CPU blade. Action: Replace the secondary CPU blade. (A1005.0067) (HyperS t ack(tm) license inst a[...]

2–Event Messages Alarm Events 59060-07 D 2-29 (A1005.006D) (Unable to synchronize with NT P server) Meaning: The switch was unable to sync hronize its time clock with the Network T ime Protocol (NTP) server . Action: Confirm that the NTP service and NTP client are enabled. Confirm that the NTP server IP address is correct and that the server is o[...]

2–Event Messages Alarm Events 2-30 59060-07 D (A1005.0074) (Blade seating is question able) Meaning: A QLogic 9000 blade is improperly installed. Action: Examine the switch and reinst all blades as needed. (A1005.0075) (Blade seating problem was resolv ed) Meaning: The QLogic 9000 blade seating problem as resolved. Action: None (A1005.0076) (Extr[...]

2–Event Messages Alarm Events 59060-07 D 2-31 (A1005.0082) (Blade fault (FW_APP_F AIL) - Internal application failure) Meaning: Internal application failure. Action: Contact your autho rized maintenance provider . (A1005.008E) (Blade fault (FW_APP_PEER_F AUL T) - Application declared error communicating with another CPU) Meaning: An application d[...]

2–Event Messages Alarm Events 2-32 59060-07 D (A1005.0106) (Fabric translation setup error , PLOGI from fc_id to fc_id OX_ID ox_id rejected) Meaning: A Port Login (PLOGI) from one transp arent route end point to another was rejected because o f hardware resource limit ations on the TR_Port or the F/FL port involved in the mapping. Action: If ther[...]

2–Event Messages Alarm Events 59060-07 D 2-33 (A1005.010C) (IPSec configuration error: IKE Pol icy policy_name : error_description ) Meaning: An error occurred while processing the specified p olicy in a saved IKE configuration. None of the configuration m odifications have been applied to the switch's active database . Action: Correct the c[...]

2–Event Messages Alarm Events 2-34 59060-07 D (A1005.01 13) (TR Port removing Proxy for port_wwn logged in at FC-ID fc_id , duplicate port name logged in at FC-ID fc_id ) Meaning: A device is logged in on another switch in the local fabric with the same port WWN as a proxy for a device in a remote fabric. The proxy created on the local switch has[...]

2–Event Messages Alarm Events 59060-07 D 2-35 ( A1005.01 1A) (DCBX_PEER_FE A TURE_E RROR error: Policy policy_name : reason ) Meaning: Peer on link has detect e d an error during DCBX [Priority Group|Priority Flow Control] exchange . Action: An error has occurred during the configuration exchange of the specified feature. The local and remo te co[...]

2–Event Messages Alarm Events 2-36 59060-07 D ( A1005.0121) (PT_P ARTNER_OFFLINE_NOTIFICA TION error: Policy policy_name : reason ) Meaning: PT port being downed because partner cannot go online . Action: Confirm that the PT p artners are configured for the same spee d. Confirm that the correct Ethernet media is inst alled. Confirm that the attac[...]

2–Event Messages Alarm Events 59060-07 D 2-37 (A1007.0002) (Security: Remote Switch wit h WorldW ide Name (WWN) wwn configured for chap, no chap configured for local swi tch. 2-way Authentication Failure) Meaning: The device WWN is either not c onf igured in t he security d at abase, or it is not configured for C hallenge Handsh ake Authenticatio[...]

2–Event Messages Alarm Events 2-38 59060-07 D (A1007.000A) (Security: Dropping loc k held by domain domain_id for number seconds) Meaning: A remote switch has held the fabric lock for too long. The local switch is dropping the lock in order t o send out a Exchange Fabric Membership Data (EFMD) fra me. Action: None (A1007.000B) (Security: EFMD Rej[...]

2–Event Messages Alarm Events 59060-07 D 2-39 (A1007.0010) (Security: Chap session Receive Chall enge indicates bad st ate, chap una ble to authenticate) Meaning: The Challenge Handsha ke Au thentication Protocol (CHAP) session state is not in the correct state for a challenge message. The port will isolate. Action: Check the remote device for a [...]

2–Event Messages Alarm Events 2-40 59060-07 D (A1007.001C) (Security: Bad Authentication F lags) Meaning: The received AUTH frame did not meet the st andard format for the frame payload. Within the header portion of the p ayload, there are some flags that are supposed to be set to zero (0). This fra me has the flags set to something other t han z[...]

2–Event Messages Alarm Events 59060-07 D 2-41 (A1007.0023) (Invalid response authenticator from RADIUS server IP_address:port , check shared secret Meaning: There is a Remote Authentication Dial In Service (RADIUS) configuration problem. Action: Confirm that the shared secret conf igured on the switch is identical to the shared secret configur ed[...]

2–Event Messages Alarm Events 2-42 59060-07 D (A1007.0029) (Security protocol not using cha p, unable to authenticate.) Meaning: A Challenge Handshake Authen tication Protocol (CHAP) negotiate frame that specifies an unsupported au thentication protocol was received. Action: Check the remote device for a possible error conditio n. Reset the port [...]

2–Event Messages Alarm Events 59060-07 D 2-43 (A1007.002D) (Ignoring RADIUS Server RADIUS_server , invalid UDP port configured) Meaning: A Remote Authentication Dial In Service (RADIUS) se rver was configured with invalid dat a for the User Data gram Protocol (UDP) port. This configuration field is requ ired to use the RADIUS server . Action: Set[...]

2–Event Messages Alarm Events 2-44 59060-07 D (A1007.0032) (Fabric conditions or configuratio ns do not currently allow for changing fabric binding.) Meaning: An attempt to change t he fabr ic binding setting was rejected due to current fabric binding configuration settings within th e active security set. Action: Check fabric binding settings an[...]

2–Event Messages Alarm Events 59060-07 D 2-45 (A1007.0039) (Ignoring RADIUS Server server , no shared secret configured) Meaning: An attempt was made to authenticate a switch login through a Remote Authentication Dial In Service (RADIUS) server , but no shared secret exists. Action: Configure a shared secret. (A1007.003A) (Using local user authen[...]

2–Event Messages Alarm Events 2-46 59060-07 D (A2001.0003) ( blade_id ) (Blade fau lt (SENSOR_F AUL T) - CLEARED) Meaning: The internal fault o n the specified Power Supply blade has been cleared. Action: None (A2001.0004) ( blade_id ) (Blade fau lt (AC_F AUL T) - ALARM CLEARED) Meaning: The specified Power Supp ly blade is rece iving power . Act[...]

2–Event Messages Alarm Events 59060-07 D 2-47 (A2004.0002) (Secondary cpu_ blade assuming control of syste m due to an administrative switchover) Meaning: Control is transferring from the prima ry CPU blade to the secondary CPU blade on a QLogic 9000 switch. Action: None (A2004.0003) (Secondary cpu_ blade assuming control of syste m due to an ope[...]

2–Event Messages Alarm Events 2-48 59060-07 D (A3003.0001) (IO n ) (Hardware error detected. Use 'show switch' for more info.) Meaning: A fatal hardware error was discovered during the Power-On-Self-T est (POST) phase of st artup. This switch is not currently operational. Action: Enter the Show Post Log command to investigate. (A3003.00[...]

2–Event Messages Alarm Events 59060-07 D 2-49 (A3005.0001-000D) (Blade fault ( value HIGH_PS_1_2V_ 2 - The [value]V volt age supply is out of range, it is too high) Meaning: A high voltage b lade fault has occurred on an fo r IBM ® BladeCenter ® Module. Action: Contact your autho rized maintenance provider . (A3005.0001-000E) (Blade fault ( val[...]

2–Event Messages Alarm Events 2-50 59060-07 D (A3007.0001-000C) (Blade fault ( blade_fault - CLEARED) Meaning: The high or low volt age IBM BladeCenter Module blade fault has cleared. Action: None (A3007.0001-000D) (Blade fault ( value NORMAL_PS_1_2V_2 - CLEARED) Meaning: The high or low volt age IBM BladeCenter Module blade fault has cleared. Ac[...]

2–Event Messages Alarm Events 59060-07 D 2-51 (A4000.0001) (t hreshold of value hit rising trigger trigger_number in value second wind ow on port port_number - ALARM SET Meaning: The switch exceeded the specified thresh old for the rising trigger in the specified sample window . Action: Investigate the specified port for problems or ad just the r[...]

2–Event Messages Alarm Events 2-52 59060-07 D (A6001.0001) (cmon: insufficient mem ory) Meaning: The Hotreset comma nd has failed due to insuf ficient memory on the switch. The switch has been return ed to its st ate before the Hotreset command was entered. Action: If accept able, enter the Reset Switch command to reboot the switch. Contact techn[...]

2–Event Messages Critical Events 59060-07 D 2-53 Critical Event s Critical events are event s tha t disrupt the ad ministration or operation of the fabric, but do not require any action before y ou can pro ceed. The following list s each critical event and the event id number and message displayed, and provides a n explanation of the message. (C)[...]

2–Event Messages Critical Events 2-54 59060-07 D (C) (8300.0018) (ZoneSet zone_set has been activated by user user_name ) Meaning: A zone set in the zoni ng dat abase has been activated (C) (8300.0019)(ZoneSet zone_set has been deactivated by user user_name ) Meaning: A zone set in the zoni ng dat abase has been deactivated. (C) (8300.001A) (A Zo[...]

2–Event Messages Critical Events 59060-07 D 2-55 (C) (8400.000E) (Switch) (Upg rading Licensed Port s to number_of_port s ) Meaning: The number of licensed port s on the switch has been upgraded. (C) (8400.000F) (Switch) (Attempted License d Port upgrade of port s that are already licensed) Meaning: The switch has already been upgraded to th e nu[...]

2–Event Messages Critical Events 2-56 59060-07 D (C) (8400.0029) (Switch) (User account_name attempted to log into switc h with an incorrect p assword) Meaning: Invalid user login attempt. (C) (8400.002A) (Switch) (User account_name attempted to log into switch with an incorrect p assword) Meaning: Invalid user login attempt. (C) (8400.002E) (Swi[...]

2–Event Messages Critical Events 59060-07 D 2-57 (C) (8400.0044) (Switch) (A reset is re quired since a Power On Self T est (POST) has never run on these port s) Meaning: After upg rading ports, it may be necessary to reset the switch so that the POST can run on the newly lice nsed ports. (C) (8400.0045) (Switch) (Upgrading License for 4G cap abi[...]

2–Event Messages Critical Events 2-58 59060-07 D (C) (8400.0053) (Switch) (The switch WWN is being upgraded) Meaning: The license upgrade was successful. (C) (8400.0054) (Switch) (radius: All RADIUS servers fa iled to respond) Meaning: None of the Remote Authentic ation Dial In Service (RADIUS) servers configured responded. Check the RADIUS serve[...]

2–Event Messages Critical Events 59060-07 D 2-59 (C) (8400.0061) (Switch) (W arning-Illegal transp arent mode configuration, Either the primary or backup map for port port_number was set to a port whose type is not TF . The mapping for this port has bee n cleared. Meaning: An attempt was made to map a TH port to a port that was not of type TF . ([...]

2–Event Messages Critical Events 2-60 59060-07 D (C) (8400.006A) (Switch) (Upgrading Lice nse for Fabric Security) Meaning: The Fabric Security Bundle license was appli ed successfully . (C) (8400.006B) (Switch) (Upgrading Lice nse for CLI Extended Credit s cap ability) Meaning: The CLI Extended Cred its li cense was applied successfully . (C) (8[...]

2–Event Messages Critical Events 59060-07 D 2-61 (C) (8400.007E) ( blade_id ) (Blade fault (FW_APP_F AIL) processing in progress, gathering support information...) Meaning: There has been an internal appl ication failure on the specified blade. (C) (8400.007F) ( blade_id ) (Blade fa ult (FW_APP_F AIL) processing in progress, shutting down port s.[...]

2–Event Messages Critical Events 2-62 59060-07 D (C) (8500.00A2) (Switch) (MSG_ID_SWITCH_ LLDPD_REST ARTED) Meaning: The LLDPD daemon has been rest arted. (C) (8600.0009) (PortApp) (Port: port_number ) (Link reset (LR) to be performed on port port_number .) Meaning: The port will perform a lin k reset (LR) due to a loss of credit problem. (C) (86[...]

2–Event Messages Critical Events 59060-07 D 2-63 (C) (8600.0018) (PortApp) (External port license became available, re-st arting downed external port s) Meaning: An external port that was prev iously down because of insu fficient port licenses is now online. (C) (8600.0019) (PortApp) (Internal port licens e count exceeded, downing internal port p[...]

2–Event Messages Critical Events 2-64 59060-07 D (C) (8700.0010) (EPort) (Port: port_number ) (Inter-Switch Link (ISL) unst able. ISL init will be held back until ISL up time is 5 seco nds) Meaning: The ISL is unstab le, indicating that the media module or the cable is bad. (C) (8700.001 1) (Eport) (Port: port_number ) (Connection failure, re mot[...]

2–Event Messages Critical Events 59060-07 D 2-65 (C) (8B00.000A) (Unable to provide profile processing in formation, the CallHome service is up dating configuration) Meaning: Profile status informatio n is not available while the Call Home service configuration is being updated. (C) (8B00.000B) (Unable to change SMTP servers beca use the CallHome[...]

2–Event Messages Critical Events 2-66 59060-07 D (C) (8F00:000E) Link S t atus status Meaning: The severity level of the lin k status has ch anged. The description field will show the reason for the link st atus.[...]

2–Event Messages Wa r n in g E v e n t s 59060-07 D 2-67 W arning Event s W arning event s are generally not disruptive, but are more significant t han Informative-level event s. The following list s the W arning event s and the event ID number and message displayed, and pr ovides an explanation of the messa ge. (W) (8300.0000) (User) (Releasing [...]

2–Event Messages Wa r n in g E v e n t s 2-68 59060-07 D (W) (8400.0018) (Switch) (User account_name login rejected - maximum logins already in use) Meaning: The attempted login was reje cted be cause there are too many sessions. There may be switch managemen t sessions open on the switch that are no longer in use. (W) (8400.001F) (Switch) (User [...]

2–Event Messages Wa r n in g E v e n t s 59060-07 D 2-69 (W) (8400.0092) (IPSec association associat ion_name has expired) Meaning: The configured lifetime for the sp ecified IPSec association has expired, and the association has been deleted from the switch's active database. (W) (8400.0093) (IPSec policy p olicy_name has expired) Meaning: [...]

2–Event Messages Wa r n in g E v e n t s 2-70 59060-07 D (W) (8B00.0010) (W ill retry sending via SMTP server ip_ad dress , port port_number ) Meaning: After receiving a transient e rror from the Simple Mail T ransfer Protocol (SMTP) server on a e-mail message se nt to a recipient, the Call Home service will attempt to resend th e e-mail message.[...]

2–Event Messages Wa r n in g E v e n t s 59060-07 D 2-71 (W) (8B00.0019) (CallHome messag e send for profile prof ile to recipient email_address failed on SMTP server ip_address , port port_n umber . Retry will not be attempted, ignoring recipient.) Meaning: The Call Home service faile d to send an e-mail message to the recipient in the named pro[...]

2–Event Messages Informative Events 2-72 59060-07 D Informative Event s Informative event s are events t hat occur in the normal activities of a fabric. The following lists th e event ID and text of the message along with an explanation of the message. (I) (8200.0001) (mserver) (Hotreset is not permitte d at this time, try again later) Meaning: T[...]

2–Event Messages Informative Events 59060-07 D 2-73 (I) (8200.0202) (mserver) (Rejecting request (GZS) for zone set zone _set_name cont aining unsupported alias member(s)) Meaning: The fabric zone server command GZS (Get Zone Set) was rejected because the requested zone set contain s one or more members that are aliases. Since aliases are not def[...]

2–Event Messages Informative Events 2-74 59060-07 D (I) (8400.0001) (Switch) (Modifying configured Dom ainID domain_ID to negotiated value domain_ID ) Meaning: The configuration is chang ing. The configured domain ID is changed to the negotiated value. (I) (8400.0006) (Switch) (Admin mode for user account_ name was canceled by user account_name )[...]

2–Event Messages Informative Events 59060-07 D 2-75 (I) (8400.0037) (Switch) (VIEnable automatically set to False since MFSEnable has be en set to T rue) Meaning: Setting the Set Config Port p arameter MFSEnable to T rue automatically set s the Set Config Port p arameters VIEnable and LCFEnable to False. (I) (8400.0038) (Switch) (LCFEnable automa[...]

2–Event Messages Informative Events 2-76 59060-07 D (I) (8400.0091) (IKE configuration modified by user_name at address session_id ) Meaning: The IKE configuration was modified by the spe cified user , who was logged in with the specified session identif ier . (I) (8400.0094) (IPSec configuration applied - number errors detected) Meaning: The sav[...]

2–Event Messages Informative Events 59060-07 D 2-77 (I) (8700.0004) (EPort) (Port: port_number ) (Remote Switch World W ide Name (WWN) is switch_WWN) Meaning: A switch with the given dom ain ID has been discovered on the given port. (I) (8700.0005) (EPort) (Port: port_number ) (Inter-Switch Link (ISL) Offline) Meaning: The specified E_Port is of [...]

2–Event Messages Informative Events 2-78 59060-07 D (I) (8F00.000A) Link Removed Meaning: A link has been removed from t he disp lay . This is either because the fabric discovery process has discovered that the lin k is no longer in the fabric, or because th e user has deleted the link manually . (I) (8F00.000B) Login Changed Meaning: The login t[...]

[...]

Corporate Headquarters QLogic Corporation 26650 Aliso V iejo Parkway Aliso V iejo, CA 92656 949 .389.6000 www .qlogic.com International Office s UK | Ireland | Germany | France | India | Japan | China | Hong Kong | Singapore | T aiwan © 201 1 QLogic Corporation. Specifications are subject to change without notice. All ri ghts reserved worldwide. Q[...]