PYLE Audio PLMR440PA инструкция обслуживания

PYLE® HYDRA PLMR440PA Marine Public Address System Controller Remote Control Included OWNER'S MANUAL[...]

Congratulations on your purchase of a PYLE PLMR440PA Marine Public Address System Controller. It has been designed, engineered and manufactured to bring you the highest level of performance and quality, and will afford you years of listening pleasure. Thank you for making a PYLE your choice for marine audio entertainment! PLMR440PA 4-Channel Marine[...]

Introduction An important member of the PYLE marine MOSFET amplifier series, we are pleased to introduce the unique PLMR440PA, a powerful amplifier with public address capabilities. This PYLE marine models features both high pass and low pass crossovers. For further flexibility in the use of a subwoofer, a variable bass boost control has been inclu[...]

Installation precautions Before you drill or cut any holes, investigate your vessel's layout very carefully. Take special care when you work near the gas tank, fuel lines, hydraulic lines and electrical wiring. Never operate the amplifier when it is unmounted. Attach all audio system components securely within the amplifier to prevent damage, [...]

Low Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same timel 4-Channel Amplifier with 4-ChannelAudio Input Source PLMR440PA Remote $Ubwo~[...]

High Level Input Wiring The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems. NOTE: Do not connect BOTH the high level and low l[...]

High Level Input Wiring The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems. NOTE: Do not connect BOTH the high level and low l[...]

Microphone Input Wiring If you wish to use the public address feature in the PLMR440PA, all you need to do is to connect the custom microphone included with the amp. When you press the button on the microphone, it automatically cuts off the input to Channels 1-4 from your audio source and presents the microphone signal to the amplifier. You can use[...]

Power and Speaker Wiring 4 Channel Mode Four Channel Mode RED """'" CONNECnONS Chassis ground point PYLE" H""RA PLMR440PA. RlURCIWINELI'CIWER"'-"'_ PIIKJCADIIIIEIISa'IalEM to REMOTE TURN-()N ORANGE term",,1 a head urn FUSE (provided) o D D I Battery I WHITE GREY CH1 Speaker [...]

Power and Speaker Wiring Bridged Mode Bridged Mode RED P<ME. CONNEcnONS Chassis ground point PYLE" HYDRA PLMR440M _"='m"=~ER ID REMOlE lURN'()N ORANGE IenTinai of head un~ FUSE (provided) {} D D I Battery I ........ """'''''' Connect the CH1J+) Isad to the Subwoofer 1 (+) tarm[...]

Speaker Wiring Tri-Mode Tir-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO. To set the amplifier to run in this mode, put the crossover switch In the FULL posifion. Insert high[...]

Troubleshooting Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. Amplifier will not power up. Check for good ground connection. Check that remote DC terminal has at least 13.8v DC. Check that there is battery power on the +terminal. Check all fuses. Check th[...]