Precor S3.25 инструкция обслуживания

Assembly Instructions S3.25 Leg Press Option[...]

S3.25 Leg Press Option Assembly Instructions page 2 IMPOR T ANT SAFETY INSTRUCTIONS Impor tant Safety Instructions Impor tant Safety Instructions Before beginning any fitness program, you should obtain a complete physical examination from your physician. Il est conseillé de subir un examen médical complet avant d’entreprendre tout programme d?[...]

S3.25 Leg Press Option Assembly Instructions page 3 T able of Contents T able of Contents Important Safety Instructions ............................................................... 2 Personal Safety Duri ng Assembly .................................................................................. 2 Obtaining S ervice ...........................[...]

S3.25 Leg Press Option Assembly Instructions page 4 1 Before Y ou Begin Before Y ou Begin Thank you for purchasing the Leg Press Option for your Precor equipment. This option will add a new dimension to your strength-training regimen. For proper installation, please read this guide thoroughly and follow the assembly instructions. Unpacking the Equi[...]

S3.25 Leg Press Option Assembly Instructions page 5 2 Preparations Preparations CAUTION: T o set up this equipment, you will need assistance. Do not attempt assembly by yourself. Y ou must review and follow the instructions in this guide. If you do not assemble and use the Leg Press Option according to the following guidelines, you could void the P[...]

S3.25 Leg Press Option Assembly Instructions page 6 1 2 3 4 5 6 3 Assembly Instructions Assembly Instructions Assembly of the Leg Press Option takes professional installers about 1 hour to complete. If this is the first time you have assembled this type of equipment, plan on significantly more time. Professional installers are highly recommended! C[...]

S3.25 Leg Press Option Assembly Instructions page 7 1 2 3 4 5 6 1. Remove the Shroud Important: For ease of assembly , the fasteners and hardware for each step are labeled and packaged in separate bags. Note: If you are assembling the Leg Press Option along with your S3.25, go directly to Step 2. Before you can attach the Leg Press Option to the u [...]

S3.25 Leg Press Option Assembly Instructions page 8 1 2 3 4 5 6 2 . Attach the C r oss Brace t o t h e S3.25 Note: If you are assembling the Leg Press Option along with the S3.25, you should complete Step 10 in the S3.25 Assembly and Maintenance Guide before attaching the Cross Brace. A. Align the Cross Brace to the S3.25 Rear Upright and secure it[...]

S3.25 Leg Press Option Assembly Instructions page 9 1 2 3 4 5 6 3. Assemble the Frame A. With someone helping you, lift the Seat Frame upright. Have your assistant hold it in place while you attach the Cross Brace in the next step. B . Attach the Cross Brace to the holes found at the front of the Seat Frame using two 3-inch bolts four washers two l[...]

S3.25 Leg Press Option Assembly Instructions page 10 1 2 3 4 5 6 D . Assemble the Footrest by resting the Pivot Arm on the Rubber Bumper . Make sure that the red arrow on the back of the Footrest points toward the ceiling. E. Attach the Footrest to the Pivot Arm and Pivot T ube using two large ½-inch by 3-¼-inch bolts four ½-inch-diameter washer[...]

S3.25 Leg Press Option Assembly Instructions page 11 1 2 3 4 5 6 4. Assemble the Seat Pads A. Attach one of the Seat Pads to the Seat Bracket Support using two 1¼-inch bolts two washers Wrench tighten. B . Lift the Pop Pin and slide the Seat Pad out of the way to assemble the other Seat Pad. C. Attach the rem aining Seat P ad to the Seat F rame us[...]

S3.25 Leg Press Option Assembly Instructions page 12 1 2 3 4 5 6 Step 5. Route the Cable 5. Route the Cable As you route the Cable through the pulleys on the Leg Press Option, wrench tighten the fasteners on each pulley as you go. Make sure that the Cable slides freely along the pulley (and beneath the cable retainer). Make sure that you are using [...]

S3.25 Leg Press Option Assembly Instructions page 13 1 2 3 4 5 6 Step 6. Assemble the Cable and Pulleys 3½" Pulley A 1 - 2" bolt 2 - washers 1 - locknut Attach this end to the Cable T ree Cable Retainer Lower Pulley Bracket This end is attached to the Leg Press Rear Upright B Discard 1 - 3¼" bolt 1 - 1" barrel spacer 2 - washe[...]

S3.25 Leg Press Option Assembly Instructions page 14 1 2 3 4 5 6 C . Reattach the end of the original Surgical T ube from the Cable T re e to its prior location and place the new Sur gic al Tube that came with the Leg Press Option to the outside of the T op Beam using one 4-inch bolt two washers two ½-inch barrel spacers one locknut Wrench tighten[...]

S3.25 Leg Press Option Assembly Instructions page 15 1 2 3 4 5 6 7. Replace the Shroud A. Pick up the Shroud and fasteners from the location where you left them in Step 4B. B . Replace the Shroud by realigning the mounting holes and inserting six 2¾-inch bolts six washers six locknuts Wrench tighten. Step 7. Replace the Shroud B 6 - 2¾" bolt[...]

S3.25 Leg Press Option Assembly Instructions page 16 1 2 3 4 5 6 4 Adjustments Adjustments B A T op Cap Weight C Chest Press Arms Weight Pin T op Cap Weight T op Weight After the Leg Press Option is assembled, you should check the Cables for proper tension. These are some obvious signs that cable problems exist: ✔ Excess slack exists in the Cable[...]

S3.25 Leg Press Option Assembly Instructions page 17 1 2 3 4 5 6 B Rotate the Cam Washer T op Cap Weight Weight Pin A T op Cap Weight C T op Weight Weight then further adjustments are needed. Continue with steps 2 and 3. 2. Rotate the Cam W asher If the T op Cap Weight does not rest on the T op Weight, you must make further adjustments. A. Remove e[...]

S3.25 Leg Press Option Assembly Instructions page 18 1 2 3 4 5 6 A B Adjust the Rubber Bumper Push the Pivot Arm up to adjust the Rubber Bumper Rubber Bumper Locknut Bracket C Weight Pin 3. Adjust the Rubber Bumper on the Leg Press Option If the T op Cap Weight still does not rest on the T op Weight, you can make one final adjustment. A. If the Cab[...]

Effective 01 August 2001 P/N 36287-108 Residential Equipment Limited Warranty Precor Incorporated warrants that all new Precor products are free of manufacturing defects in workmanship and materials. Parts repaired or replaced under the terms of this warranty will be warranted for the remainder of the original warranty period only . This warranty b[...]

Precor Incorporated 20031 142nd Avenue NE P .O. Box 7202 Woodinville, W A USA 98072-4002 PLACE ST AMP HERE W arranty Registration Card Please fill out the W arranty Registration and mail it to Precor . ▼ S3.25 Leg Press Option Specifications Length: 60 inches (152 cm) Height: 33 inches (84 cm) Width: 30 inches (76 cm) Shipping weight: 125 lb (57 [...]